When running 'bridge fdb dump' on Felix, sometimes learnt and static MAC
addresses would appear, sometimes they wouldn't.
Turns out, the MAC table has 4096 entries on VSC7514 (Ocelot) and 8192
entries on VSC9959 (Felix), so the existing code from the Ocelot common
library only dumped half of Felix's MAC table. They are both organized
as a 4-way set-associative TCAM, so we just need a single variable
indicating the correct number of rows.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM SoC fixes from Arnd Bergmann:
"A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I
found after restarting my randconfig build testing that had been
dormant for a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: imx8: select SOC_BUS
soc: tegra: fix tegra_pmc_get_suspend_mode definition
soc: fsl: dpio: avoid stack usage warning
soc: fsl: dpio: fix incorrect pointer conversions
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: bcm283x: Disable dsi0 node
firmware: xilinx: make firmware_debugfs_root static
drivers: soc: xilinx: fix firmware driver Kconfig dependency
ARM: dts: bcm283x: Add cells encoding format to firmware bus
ARM: dts: OMAP3: disable RNG on N950/N9
Support 4 PTP programmable pins with only PTP_PF_PEROUT function
for now. The PTP_PF_EXTTS function will be supported in the
future, and it should be implemented separately for Felix and
Ocelot, because of different hardware interrupt implementation
in them.
Since the hardware is not able to support absolute start time,
the periodic clock request only allows start time 0 0. But nsec
could be accepted for PPS case for phase adjustment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 5 PTP_PINS register groups on Ocelot switch.
Except the one used for TOD operations, there are still
4 register groups for programmable pins. So redefine the
4 programmable pins.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.
This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP is disabled, the function is not defined,
causing a link failure:
arm-linux-gnueabi-ld: drivers/cpuidle/cpuidle-tegra.o: in function `tegra_cpuidle_probe':
cpuidle-tegra.c:(.text+0x24): undefined reference to `tegra_pmc_get_suspend_mode'
Change the #ifdef check according to the definition.
Fixes: 382ac8e22b ("cpuidle: tegra: Disable CC6 state if LP2 unavailable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
To rehash a previous explanation given in commit 1c44ce560b ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.
The configuration for this native VLAN is driven in 2 ways:
- Set the egress port rewriter to strip the VLAN tag for the native
VID (as it is egress-untagged, after all).
- Configure the ingress port to drop untagged and priority-tagged
traffic, if there is no native VLAN. The intention of this setting is
that a trunk port with no native VLAN should not accept untagged
traffic.
Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.
But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
- Native VLAN of the port - its value is held in port->vid.
- VLAN awareness state of the port - currently there are some issues
here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
0. The driver configures a pvid of zero for each port, when in
standalone mode. While the bridge configures a default_pvid of 1 for
each port that gets added as a slave to it.
1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
The VLAN-filtering-dependent portion of the native VLAN
configuration is done, considering that the native VLAN is 0.
2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
untagged=true. The native VLAN changes to 1 (change which gets
propagated to hardware).
3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
VLAN-filtering-dependent portion of the native VLAN configuration,
for the new native VLAN of 1. One can notice that after toggling "ip
link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
type bridge vlan_filtering 1", the new native VLAN finally makes it
through and untagged traffic finally starts flowing again. But
obviously that shouldn't be needed.
So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.
*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
- Ocelot: ocelot_port_private->vlan_aware
- Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.
Fixes: 97bb69e1e3 ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
Pull ARM SoC updates from Arnd Bergmann:
"The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including cpuidle,
pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms"
* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
ARM: qcom: Add support for IPQ40xx
ARM: mmp: replace setup_irq() by request_irq()
ARM: cns3xxx: replace setup_irq() by request_irq()
ARM: spear: replace setup_irq() by request_irq()
ARM: ep93xx: Replace setup_irq() by request_irq()
ARM: iop32x: replace setup_irq() by request_irq()
arm: mach-dove: Mark dove_io_desc as __maybe_unused
ARM: orion: replace setup_irq() by request_irq()
ARM: debug: stm32: add UART early console support for STM32MP1
ARM: debug: stm32: add UART early console support for STM32H7
ARM: debug: stm32: add UART early console configuration for STM32F7
ARM: debug: stm32: add UART early console configuration for STM32F4
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
...
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
This patch is a trivial passthrough towards the ocelot library, which
support port policers since commit 2c1d029a01 ("net: mscc: ocelot:
Implement port policers via tc command").
Some data structure conversion between the DSA core and the Ocelot
library is necessary, for policer parameters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has 384 policers that can be allocated to ingress ports,
QoS classes per port, and VCAP IS2 entries. ocelot_police.c
supports to set policers which can be allocated to police action
of VCAP IS2. We allocate policers from maximum pol_id, and
decrease the pol_id when add a new vcap_is2 entry which is
police action.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.
Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpuidle: tegra: Changes for v5.7-rc1
These changes unify CPU idle support for Tegra20, Tegra30 and Tegra114.
* tag 'tegra-for-5.7-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
Link: https://lore.kernel.org/r/20200313165848.2915133-9-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: tegra: Core changes for v5.7-rc1
These patches a preparatory work to move the CPU idle drivers into
drivers/cpuidle.
* tag 'tegra-for-5.7-arm-core' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
ARM: tegra: Rename some of the newly exposed PM functions
ARM: tegra: Expose PM functions required for new cpuidle driver
ARM: tegra: Propagate error from tegra_idle_lp2_last()
ARM: tegra: Change tegra_set_cpu_in_lp2() type to void
ARM: tegra: Remove pen-locking from cpuidle-tegra20
ARM: tegra: Add tegra_pm_park_secondary_cpu()
ARM: tegra: Compile sleep-tegra20/30.S unconditionally
Link: https://lore.kernel.org/r/20200313165848.2915133-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The driver's code is refactored in a way that will make it easy to
support Tegra30/114/124 SoCs by this unified driver later on. The
current functionality is equal to the old Tegra20 driver, only the
code's structure changed a tad. This is also a proper platform driver
now.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The upcoming unified CPUIDLE driver will be added to the drivers/cpuidle/
directory and it will require all these exposed Tegra PM-core functions.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[treding@nvidia.com: fixup missing include rename]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Extend the Tegra194 IO pad table with additional information such as pin
names and 1.8/3.3 V settings to allow a table of voltage control pins to
generated from it. This is similar to what's done for older chips and is
needed to support high-speed modes for SDHCI where switching the pins to
1.8V or 3.3V is necessary.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
David S. Miller
Vladimir Oltean
Linus Torvalds
Yangbo Lu
Arnd Bergmann
Xiaoliang Yang
Li Yang
Dmitry Osipenko
Venkat Reddy Talla