target configure -work-area-xxx calls target_free_all_working_areas()
and sets the desired new parameter. Without this change the working area
does not get reallocated if it has been allocated before.
target_free_all_working_areas() results in work area containing one block
marked as free.
Completely free working area in target_free_all_working_areas()
Change-Id: I79c681082f32f2a96a2b40eb3b8751e427549693
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4797
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The block of code moved without any changes
Change-Id: I70b82dc3315dcc3f34de0537b362bee230007d02
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4796
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove option 'srst' which is not recognized from on-line help and texi.
Check parameter and return syntax error if wrong option is entered.
Change-Id: I87daa423a9f53193a0b015080594820b933628f5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4795
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Cortex-M0, M0+ and M1 do not support VECTRESET bit in AIRCR.
Without this change the 'reset' command silently fails if VECTRESET
is requested.
Detect these cores, show warning if VECTRESET is about to use
and use SYSRESETREQ instead.
Change-Id: Ief174373e3ef0e6b287c57911c0aca4dfa8209f2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4794
Tested-by: jenkins
Reviewed-by: Jean-Christian de Rivaz <jcamdr70@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This commit adds TARGET_HALTED check in armv8_get_core_reg32()
and armv8_set_core_reg32() to void a crash issue when gdb connects
but fails to halt the ARM core. Similar logic can be found in
armv8_get_core_reg() and armv8_set_core_reg().
Below is the call stack information of this case when gdb connects.
(gdb) bt
regnum=regnum@entry=0, dpm=0x990110) at src/target/armv8_dpm.c:657
r=0x9c7240, regnum=0, mode=<optimized out>) at src/target/armv8_dpm.c:974
at src/target/armv8.c:1487
packet=0x8ec8e0 <gdb_packet_buffer.9962> "g",
packet_size=<optimized out>, connection=<optimized out>)
at src/server/gdb_server.c:1200
at src/server/gdb_server.c:3180
command_context=command_context@entry=0x935010)
at src/server/server.c:566
...
Change-Id: I159837b533f110998184f910a0abe48409bd58f1
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/4758
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Arm architecture reference manual DDI0406C reports at page 2024 in
table C3-1 the processor behaviour on debug events depending on
the debug-mode (none, monitor or halt), mode selected through the
bits MDBGen and HDBGen in DSCR register.
The halt request is served independently from the debug-mode. Thus
it's useless to enable the halt debug-mode in cortex_a_halt() by
setting the bit HDBGen (macro DSCR_HALT_DBG_MODE).
On the other side, halting for a breakpoint, a watchpoint or a
vector catch requires being in halt debug-mode.
Today HDBGen is set only in cortex_a_halt(), so we are forced to
halt the core at least once before it can be halted for hitting a
breakpoint/watchpoint/vector-catch. This is annoying since there
is no need to halt the target to set a HW breakpoint.
Move in cortex_a_init_debug_access() the selection of the halt
debug-mode, so the mode is set during examine.
To prevent a misconfigured hardware breakpoint/watchpoint/vector
catch to halt the target when OpenOCD has already quit, return to
debug-mode none at OpenOCD exit.
Change-Id: I68a1c51de3572ca1b89e90caf7eb20374268e926
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4783
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
DEBUG_WAIT is useful to debug adi_jtag issue,
and the WCR register is replaced by DLCR for DP registers update
in commit 150b7d26f2.
Change-Id: I3faa9ea8a6adacd3d5275e40382801da731db32f
Signed-off-by: YanLin Zhu <zhuyanlin@pinecone.net>
Reviewed-on: http://openocd.zylin.com/4804
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
The OpenOCD commands that have been wrapped with 'ocd_bouncer' are
executed within two levels of nested proc's:
# see register_command_handler() in src/helper/command.c
proc my_command {args} {eval ocd_bouncer my_command $args}
# see ocd_bouncer in src/helper/startup.tcl
proc ocd_bouncer {name args} {
... [eval ocd_my_command $args] ...
}
This causes the stack frame of 'ocd_my_command' to be the same one
of proc 'ocd_bouncer', thus two levels below the stack frame of the
caller of 'my_command'. This is an issue with commands that receive
a variable by name and have to resolve them to access the value.
E.g. the command
<target> mem2array arrayname bitwidth address count
is wrapped; it receives the name of the array but fails to resolve
it in the current stack frame. Instead, the commands
mem2array arrayname bitwidth address count
ocd_<target> mem2array arrayname bitwidth address count
are not wrapped and can directly access the array because they share
the same stack frame of the caller.
Same situation with the symmetric commands 'array2mem'.
How to test:
within a telnet connection, run the following set of commands,
eventually replacing the address 0x08000000 with a valid readable
address of your <target>,
unset -nocomplain v1 v2 v3
info vars v?
mem2array v1 32 0x08000000 1
<target> mem2array v2 32 0x08000000 1
ocd_<target> mem2array v3 32 0x08000000 1
info vars v?
and notice that only v1 and v3 are now allocated. The array v2 has
been allocated in the temporarily stack frame of proc ocd_bouncer,
together with its local variables, and then lost when proc ended.
Fixed by executing the wrapped commands with the command 'uplevel'
instead of 'eval'. The amount of levels to skip is checked to avoid
errors in the unusual case 'ocd_bouncer' is called directly without
the first level of wrapper.
Change-Id: Iff90fb8921faf9b5ab04f61062a530578cc20d78
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4731
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Slow version of blank check procedure reads target memory sector-by-sector
using 1 KB chunks. Due to bug in chunk size calculation algorithm the actual
size of the chunk is always 1 KB even if sector size is smaller.
This causes out-of-boundary read of the last sector.
Steps to reproduce:
1) Use target with small sectors (e.g. psoc6 with 512-byte sectors)
2) set WORKAREASIZE_CM0 0
3) flash erase_check 1
Running slow fallback erase check - add working memory
Info : SWD DPIDR 0x6ba02477
Error: Failed to read memory at 0x14008000
unknown error when checking erase state of flash bank #1 at 0x14000000
Bank is erased
Change-Id: I03d0d5fb3a1950ae6aac425f5e24c7fd94b38325
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4785
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch removes use of register write protection in protect() and
protect_check() now that Change 4765 has merged.
Change-Id: I42c429dc283c5b53989a6b98ebfc58214274ff16
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4791
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds support for instruction tracing to eSi-RISC targets. The
command interface is borrowed heavily from ETM; eSi-Trace uses a less
sophisticated model for tracing, however the setup and usage is similar.
This patch also cleans up the command interfaces of the other esirisc
command groups and adds additional debugging information to log messages
when dealing with CSRs.
This patch "finalizes" support for 32-bit eSi-RISC targets.
Change-Id: Ia2a9de79a3c7c066240b5212721fb1b7584a9a45
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4780
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
original CC3200 launchpad works only with ti-icdi driver
which stopped to work after merging to master commit
d02de3a8a9
Change-Id: I247b5d99831fa744de1fdc5b8a7cffdf49fe953c
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-on: http://openocd.zylin.com/4792
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When GDB analyses the status of the target it try to guess the
current stack frame and issues few memory read.
E.g. on ARM targets GDB uses R11 value as a potential frame-pointer
and reads at the address pointed by R11.
The address of such memory read is not always valid and can trigger
an address translation failure.
Replace LOG_ERROR with LOG_WARNING in case the virtual address does
not have a hit in TTB; print the virtual address in the warning
message and discriminate the two identical messages with [1]/[2].
Change-Id: I288b8cd26bec2543c4f1c16b7c06dc47d5d843d1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4602
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
For compatibility with libusb1, define LIBUSB_TRANSFER_TYPE_BULK
in libusb0.
Remove the #ifdef HAVE_LIBUSB1 in jtag/driver/aice
This also fixes a compile error in jtag/drivers/openjtag with
libusb0.
Change-Id: I827b77eac10216759eb31aab461b2b63cabaf195
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4700
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Updates support for L4+ device id: 0x470 added by #4310
Extends #4641 to account for L4+ use of multiple DBANK option bits
Enables L4+ 1M and 2M devices to be programmed using sector erase
Change-Id: I42bb379d7d97986f4506423e3da503d07c787c6b
Signed-off-by: bob <rea952@gmail.com>
Reviewed-on: http://openocd.zylin.com/4777
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove inappropriate use of bank_number.
Change-Id: I11be1f2540cb09a3ccede35312f90bc8276af338
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4788
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Added fixes found in additional code reviews.
Remove inappropriate use of bank_number field and updated
documentation to reflect the change.
Restored functionality to cc2538.cfg file because previous
change removed the cc26xx.cfg file because the flash support
changes made it obsolete. Rolled the previous cc26xx.cfg
file into cc2538.cfg and updated it to work with other
recent changes. Tested using a SmartRF06 Evaluation
board with embedded XDS100v3 and external XDs110.
Change-Id: Ia19d00cf8055c5c0f1acc53aa23fd06a80fd2ebc
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4787
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit f1be0e6af2 ("HELPER/LOG:
review unused symbols") removed a set of unused functions and,
as consequence, there is no code anymore that sets the variable
"log_forward_count". But, the commit above did not removed the
code (now dead) that depends on "log_forward_count" set.
Remove the code dependant on "log_forward_count" set and the
variable itself.
Change-Id: I6efe93d1dccbe13c409c5bc55ba47a2684c0e3ac
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4779
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
