The rtos hwthread has been merged in 2019 with commit 85ba2dc4c6
("rtos/hwthread: add hardware-thread pseudo rtos").
During review in patchset 19 the name of the rtos has been changed
from 'hawt' to 'hwthread'.
Some target config file was already merged ready for hwthread, but
keeping the relevant lines commented and still reporting the old
name.
Enable rtos hwtread to the target that were supposed to use it.
Fix the name of the rtos.
Change-Id: I877862dcdba39f26462bb542bac06d1a5f5f222d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7384
Tested-by: jenkins
This patch is picked from the tcl part of OpenOCD-Nuvoton's commit
("flash: supported Nuvoton M4 series. jtag: Used HW reset instead of
auto reset. tcl: added a configuration file for Nuvoton M4 series.") [1]
to support the communication with Nuvoton's Cortex-M4 chips: M541 &
NUC442/472 series.
This patch has been tested with Nuvoton's NuTiny-SDK-NUC472 development
board [2].
The code comes from the commit basically. Jian-Hong Pan tweaked for the
compatibility with current OpenOCD. So, leave the author as Zale Yu.
[1]: https://github.com/OpenNuvoton/OpenOCD-Nuvoton/commit/c2d5b8bfc705
[2]: https://www.nuvoton.com/export/resource-files/UM_NuTiny-SDK-
NUC472_EN_Rev1.02.pdf
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I27ac58dd1c98a76e791a4f1117c31060cf5522e8
Reviewed-on: https://review.openocd.org/c/openocd/+/7330
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
rp2040-core0.cfg configuration file was intended for a special adapter
which selects a SWD multidrop target on its own. This means
that rp2040-core0.cfg is totally unusable with a standard SWD
adapter. The file was marked as deprecated in 0.12 release.
The reworked rp2040.cfg can be restricted to use just one core:
openocd ... -c 'set USE_CORE 0' -f target/rp2040.cfg
Remove the obsoleted config.
Change-Id: Id886471622bb4a8cb83f5c4c3660657407aaaf74
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7326
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add the variable selected configuration for SMP debug with rtos hwthread.
Use SMP by default.
Change-Id: I1c37d91688a3ab58d65c15686737892965711adc
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7242
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The nds32 code triggers ~50 errors/warnings with scan-build.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
For all the reasons above, this code has been deprecated with
commit 2e5df83de7 ("nds32: deprecate it, together with aice
adapter driver") and tagged to be dropped before v0.13.0.
Let it r.i.p. in OpenOCD git history.
While there, drop from checkpatch list the camelcase symbols that
where only used in this code.
Change-Id: Ide52a217f2228e9da2f1cc5036c48f3536f26952
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7382
Tested-by: jenkins
The speed coefficient for Raspberry Pi 2 was probably calibrated
for a scaled down clock frequency.
To prevent JTAG/SWD overclocking, use the value corresponding
to the 'official' maximum CPU clock.
Change-Id: Iaff58b092198dce6d6552c9d31d6a3ba4aaaa2d5
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7305
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
The existing rp2040-core0.cfg configuration file was intended
for a special adapter which selects a SWD multidrop target on its own.
This means that rp2040-core0.cfg is totally unusable with a standard SWD
adapter.
To fix the problem, mark rp2040-core0.cfg as deprecated and
add rp2040.cfg, a basic config file with multidrop target selection.
Change-Id: I5194e42f529a2d9645481424b7c66ab61efa44ee
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7275
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The work area should be backed up.
The flash probe runs an algorithm on the target CPU.
The flash is probed during gdb connect if gdb_memory_map is enabled
(is enabled by default).
Without backup the target memory gets corrupted on gdb connect.
Change-Id: I3344b9dc6cbf904d49f3b05ab104b541d1d63422
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7257
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Since all the device definition when accessing device from jtag is also
valid when accessing from swd, lets make sure the configuration can
handle the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I5af071137fd8c3b52cc4ef72401f8eba952f9cad
Reviewed-on: https://review.openocd.org/c/openocd/+/7090
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Still some config file uses deprecated commands.
Replace them with the new commands.
Change-Id: I6ccbfb832e0ad2012e9af160bd2d92ad104af2bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7181
Tested-by: jenkins
- Config files for DAP/JTAG and DAP/SWD systems
- Xtensa core config definitions for NXP RT685 with Xtensa HiFi DSP
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I9c3280052073d86e09c7553de661eb8662a95c4a
Reviewed-on: https://review.openocd.org/c/openocd/+/7145
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
