ESP32-S3 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I44e17088030c96a9be9809f6579a4f16dbfc5794
Reviewed-on: https://review.openocd.org/c/openocd/+/6990
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750
Reviewed-on: https://review.openocd.org/c/openocd/+/6989
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
On ADIv6 the system root ROM table is found by reading the DAP DP
registers BASEPTR0 and BASEPTR1.
Add option 'root' to the commands 'dap info' to let it retrieve
the system root ROM table's AP from DAP DP, then use such AP for
following dump.
Change-Id: I1789457a005faa3870c5d14f763378d2f6a5f095
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6462
Tested-by: jenkins
ADIv5 DAP can only have 256 AP, while ADIv6 can provide till
2**40 (1,099,511,627,776) AP per DAP.
Reuse the field ap_num in struct adiv5_ap, currently used on ADIv5
to hold the ADIv5 AP number (apsel), to contain the ADIv6 AP base
address.
Convert struct adiv5_ap->ap_num to 64 bit and initialize it to
DP_APSEL_INVALID for unused AP.
Restrict dap_find_get_ap() to ADIv5 only. To be enhanced.
On ADIv6, let dap_get_ap() return an already allocated AP, or
allocate and return an unused AP.
Add function is_ap_num_valid() and use it.
Change-Id: Ib2fe8c7ec0d08393cd91c29fdac5d632dfc1e438
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6461
Reviewed-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Tested-by: jenkins
It is a common requirement to automatically execute some command
after "init".
This can be achieved, either in scripts or through OpenOCD command
line, by explicitly calling "init" followed by the commands.
But this approach fails if the request for post-init commands is
spread across configuration files; only one of the files can split
pre-init and post-init status by calling "init".
The common workaround is to "rename" the command "init" and
replace it with a TCL proc that calls the original "init" and the
post-init commands. E.g. in Zephyr script [1].
To simplify and formalize the post-init execution, use a TCL list
that contains the list of commands to be executed. Every script
can contribute adding new commands, e.g. using "lappend".
In the same way, formalize the pre-shutdown execution with a TCL
list of user commands to be executed before OpenOCD exit.
Document them and add trivial examples.
Drop from documentation the suggestion to rename "shutdown".
Change-Id: I9464fb40ccede3e7760d425873adca363b49a64f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Link: [1] https://github.com/zephyrproject-rtos/zephyr/blob/zephyr-v2.7.1/boards/arm/nucleo_h743zi/support/openocd.cfg#L15
Reviewed-on: https://review.openocd.org/c/openocd/+/6851
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Added bluenrg-lps support
Added file for the board steval-idb012v1
Fixed size_info information using a mask
Changed the if condition in bluenrg-x.cfg to be valid only for bluenrg-1 and bluenrg-2
Signed-off-by: Salvatore Giorgio PECORINO <salvatore-giorgio.pecorino@st.com>
Change-Id: Ic0777ec0811ee6fac7d5e1d065c4629e47d84a1f
Reviewed-on: https://review.openocd.org/c/openocd/+/6928
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The deprecation was already in the documentation since v0.11.0
through commit 85ba2dc4c6 ("rtos/hwthread: add hardware-thread
pseudo rtos") but OpenOCD was not informing the user printing a
runtime message.
Remove the deprecated method from the documentation and print a
deprecated message at runtime.
There is no reliable way to print the same message in GDB console,
so we have to rely on user noticing it in the OpenOCD log.
Target is to remove the functionality after v0.12.0.
Change-Id: Idd2d9e3b6eccc92dcf0432c3c7de2f8a0fcabe9f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6862
Tested-by: jenkins
The device has compatible flash macro with STM32F1 family, reuse
stm32f1x driver code.
Detect non-ARM target - for simplicy test target type name 'riscv'
and the address has 32 bits.
In case of RISC-V CPU use simple chunked write algo - async algo
cannot be used as the core implemented in this device doesn't
allow memory access while running.
Change-Id: Ie3886fbd8573652691f91a02335812a7300689f7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6704
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
The target nds32 and its companion adapter aice have not received
any real improvement since 2013.
It has been hard to keep them aligned during the evolution of
OpenOCD code, with no way for maintainers to really check if they
are still working.
No real documentation is present for them in OpenOCD.
The arch nds32 has been dropped from Linux kernel v5.18-rc1.
Deprecate both nds32 target and aice adapter with the target of
dropping them for v0.13.0.
Remove automatic build of aice, forcing user to select it.
Change-Id: Ib465d676246fa3b4e95c3d399ba9a5cf1f8b3baf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6887
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
This command permits the usage of a TCP port to perform debug and stdio
operations:
- debug : READC, WRITEC and WRITE0
- stdio : READ, WRITE
This will permit the separation of semihosting message from OpenOCD log,
and separate semihosting messages per core.
syntax: arm semihosting_redirect (disable | tcp <port> [debug|stdio|all])
this allows to select which operations to be performed via TCP (debug,
stdio or all (default)).
Note: for stdio operations, only I/O from/to ':tt' file descriptors are
redirected.
tested using netcat on ubuntu
Change-Id: I37053463667ba109d52429d4f98bc98d0ede298d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5562
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace 'mem2array' and 'array2mem' with a Tcl wrapper that
internally uses 'read_memory' and 'write_memory'.
The target-specific 'mem2array' and 'array2mem' functions
remain for now.
Change-Id: If24c22a76ac72d4c26916a95f7f17902b41b6d9e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6308
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
These functions are meant as replacement for 'mem2array' and
'array2mem'.
The main benefits of these new functions are:
* They do not use Tcl arrays but lists which makes it easier
to parse (generate) the data. See the Python Tcl RPC code
in contrib as a negative example.
* They do not operate on Tcl variables but instead return (accept)
the Tcl list directly. This makes the C and Tcl code base
smaller and cleaner.
* The code is slightly more performant when reading / writing
large amount of data. Tested with a simple Python Tcl RPC
benchmark.
Change-Id: Ibd6ece3360c0d002abaadc37f078b10a8bb606f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6307
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Enabling a portion (0x100 - 0x107) of the user defined semihosting
operation number range (0x100 - 0x1FF) to be processed with the help of
the existing target event mechanism, to implement a general-purpose Tcl
interface for the target available on the host, via semihosting
interface.
Example usage:
- The user configures a Tcl command as a callback for one of the newly
defined events (semihosting-user-cmd-0x10X) in the configuration
file.
- The target can make a semihosting call with <opnum>, passing optional
parameters for the call.
If there is no callback registered to the user defined operation number,
nothing happens.
Example usage: Configure RTT automatically with the exact, linked
control block location from target.
Signed-off-by: Zoltán Dudás <zedudi@gmail.com>
Change-Id: I10e1784b1fecd4e630d78df81cb44bf1aa2fc247
Reviewed-on: https://review.openocd.org/c/openocd/+/6748
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some CPU wrongly indicate the bypas bit in the codeid.
It's the case of the NanoXplore NG-ULTRA chip that export a
configurable (and potentially invalid) ID for one of
its component.
Add an option to ignore it.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Change-Id: Ic59743f23bfc4d4e23da0e8535fec8ca9e87ff1a
Reviewed-on: https://review.openocd.org/c/openocd/+/6802
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
With jimtcl 0.81 the syntax of the TCL command 'expr' requires the
multiple arguments to be within curly brackets.
Update the examples in the documentation to follow the new syntax.
While there, split one example to avoid it to exceed the line size
during pdf document generation.
Change-Id: I91cca419f8273415ccb0c2ce369fc6ac476e34e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6809
Tested-by: jenkins
