Rename the "armv4_5" command prefix to straight "arm" so it makes
more sense for newer cores. Add a simple compatibility script.
Make sure all the commands give the same "not an ARM" diagnostic
message (and fail properly) when called against non-ARM targets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Kick in ETM (and ETB) support for ARM11. Tested on OMAP 2420,
so update that configuration. (That's an ARM1136ejs, ETB,
OpenGL ES1.1, C55x DSP, etc.)
Also update the other ARM11 ETM + ETB targets in the tree
to set up these modules. (Not tested.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Various cores with an ETB have its TAP misnamed ... either as a
boundary scan TAP or as the iMX "Secure JTAG Controller" (which
is, among other things, a JRC that could be used to shorten
scan chains).
Use the correct name for these TAPs, which we can recognize since
their IDs were assigned by ARM and these chips all document the
presence of an ETB. The 0x2b900f0f is ETB11; the 0x1b900f0f
is an older module, just called "ETB".
Also shrink the ETB's IR configuration; the default IR-Capture
value is fine, and the mask can specify that all four bits are
safe to check (per ARM documentation).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
General rule, this is all board-specific and doesn't belong
in target config files. Some of these were just cosmetic.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Here's a patch for the double-reset problem on STM32. I've tested
downloading and debugging with GDB and Eclipse, and everything seems
to work fine.
This effectively sets reset_config to none. trst_only would also
be ok, but that's better left to a board configuration file since
not all boards wire it up.
The NVIC is used to trigger reset, which at least on this chip also
pulses nSRST so the whole system does get rest -- exactly once.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's been about a year since these were deprecated and, in most
cases, removed. There's no point in carrying that documentation,
or backwards compatibility for "jtag_device" and "jtag_speed",
around forever. (Or a few remnants of obsolete code...)
Removed a few obsolete uses of "jtag_speed":
- The Calao stuff hasn't worked since July 2008. (Those Atmel
targets need to work with a 32KHz core clock after reset until
board-specific init-reset code sets up the PLL and enables a
faster JTAg clock.)
- Parport speed controls don't actually work (tops out at about
1 MHz on typical HW).
- In general, speed controls need to live in board.cfg files (or
sometimes target.cfg files), not interface.cfg ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The semantics of "-work-area-virt 0" (or phys) changed with
the patch to require specifying physical or virtrual work
area addresses. Specifying zero was previously a NOP. Now
it means that address zero is valid.
This patch addresses three related issues:
- MMU-less processors should never specify work-area-virt;
remove those specifications. Such processors include
ARM7TDMI, Cortex-M3, and ARM966.
- MMU-equipped processors *can* specify work-area-virt...
but zero won't be appropriate, except in mischievous
contexts (which hide null pointer exceptions).
Remove those specs from those processors too. If any of
those mappings is valid, someone will need to submit a
patch adding it ... along with a comment saying what OS
provides the mapping, and in which context. Example,
say "works with Linux 2.6.30+, in kernel mode". (Note
that ARM Linux doesn't map kernel memory to zero ...)
- Clarify docs on that "-virt" and other work area stuff.
Seems to me work-area-virt is quite problematic; not every
operating system provides such static mappings; if they do,
they're not in every MMU context...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Config for Intel's "Lubbock" PXA255 development board. Even more
so than the PXA255 itself, this is obsolete. AFAIK this was the
first generally available development platform for PXA255. Intel
stopped providing these after other devel boards became available.
One interesting thing about this board from the OpenOCD perspective
is probably its flash configuration. Each bank is 32 bits wide,
built from two 16-bit StrataFlash chips wired in parallel. This
doubles throughput ... it reads/writes 32 bits in the time a single
chip takes to write just 16 bits.
This conf mostly works, given XScale bugfixes, but has some issues
(notably: no access to the on-board SDRAM) flagged by FIXMEs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Gets rid of the runtime warning "stm32.bs: nonstandard IR mask"
[dbrownell@users.sourceforge.net: line lengths, note issue, section ref]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This gets rid of runtime warnings from the use of numbers.
STM32 and LPC2103 were tested. Other LPC updates are the
same, and so are safe. The CFI updates match other tested
changes now in the tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add interface configs for two new high speed JTAG
adapters from Olimex. They need some other speed
related tweaks to work well at high speed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
