Driver for DesignWare SPI controller, found on many SoCs (see compatible
list in Linux device tree bindings
Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml). This
implementation only supports MIPS as it was the only one available for the
tests, however, adding support for other architectures should require only
few adjustments. Driver relies on flash/nor/spi.h to find Flash chip info.
Driver internal functions support 24bit addressing mode, but due to
limitations of flash/nor/spi.h, it is not used. The reported writing speed
is about 60kb/s.
Lint, sanitizer and valgrind reported warnings were not related to the
driver.
Change-Id: Id3df5626ab88055f034f74f274823051dedefeb1
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8400
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This updates the flash driver to support more than one bank.
This is required to support the cc1352p7 which has two banks.
This only have been tested on a cc1352p7.
The loader has been built using a gcc-arm-none-eabi-4_8-2014q3
toolchain.
Change-Id: Ia813421ececd96d6e2fd4dae910ad60fcc3d3c88
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8192
Tested-by: jenkins
Reviewed-by: Vaishnav M A <vaishnav@beagleboard.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Simply move numicro M0 flash write assembly to contrib/loaders. Also,
modify corresponding Makefile and generated numicro_m0.inc.
To make the path more general, this patch rename the path
"contrib/loaders/flash/numicro_m4" to "contrib/loaders/flash/numicro" as
well.
Signed-off-by: Jian-Hong Pan <chienhung.pan@gmail.com>
Change-Id: I9adea24c2b3c97319a9b015cf50257f3d131dc26
Reviewed-on: https://review.openocd.org/c/openocd/+/7346
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
With the old checkpatch we cannot use the correct format for the
SPDX tags in the file .c, in fact the C99 comments are not allowed
and we had to use the block comment.
With the new checkpatch, let's switch to the correct SPDX format.
Change created automatically through the command:
sed -i \
's,^/\* *\(SPDX-License-Identifier: .*[^ ]\) *\*/$,// \1,' \
$(find src/ contrib/ -name \*.c)
Change-Id: I6da16506baa7af718947562505dd49606d124171
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7153
Tested-by: jenkins
Some file miss completely the license tag.
Add the SPDX tag, using the same GPL-2.0-or-later license of the
OpenOCD project.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I24bd362eeb6b74f09aceb9b757d45cbfa4afe334
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7160
Tested-by: jenkins
Replace the GPLv2-or-later boilerplate with the SPDX tag.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I380d552940f1c405309a3346454251c0e80b5a45
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7159
Tested-by: jenkins
Replace the BSD-3-Clause boilerplate with the SPDX tag.
Add the SPDX tag and the copyright to two makefiles that were
added by TI with the other files in their respective folder.
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: I3ad1b2dbdb6054b74dcc26e394c9223ba0427caf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7158
Tested-by: jenkins
Put the SPDX tag alone in a comment in the first line of the file.
Replace the obsolete GPL-2.0+ tag
The SPDX tag on files *.c is incorrect, as it should use the C99
single line comment using '//'. But current checkpatch doesn't
allow C99 comments, so keep using standard C comments, by now.
Change-Id: Ia91b0f7da42c439b6340bbe81983b86b68f6d65c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7156
Tested-by: jenkins
ESP32-S3 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I44e17088030c96a9be9809f6579a4f16dbfc5794
Reviewed-on: https://review.openocd.org/c/openocd/+/6990
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
ESP32 is a dual core Xtensa SoC
Not full featured yet. Some of the missing functionality:
-Semihosting
-Flash breakpoints
-Flash loader
-Apptrace
-FreeRTOS
Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Change-Id: I76fb184aa38ab9f4e30290c038b5ff8850060750
Reviewed-on: https://review.openocd.org/c/openocd/+/6989
Tested-by: jenkins
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The device has compatible flash macro with STM32F1 family, reuse
stm32f1x driver code.
Detect non-ARM target - for simplicy test target type name 'riscv'
and the address has 32 bits.
In case of RISC-V CPU use simple chunked write algo - async algo
cannot be used as the core implemented in this device doesn't
allow memory access while running.
Change-Id: Ie3886fbd8573652691f91a02335812a7300689f7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6704
Tested-by: jenkins
Reviewed-by: Tim Newsome <tim@sifive.com>
* Move more smarts into the target algorithm code, and rewrite that in C
so it's easier to understand/maintain.
* Support >24-bit addresses.
* Check for errors.
Change-Id: I3b1a143589fe6defafb8f95820aa682acc9646e7
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6679
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The busy flag must be polled after each half-page write.
At low clock speeds, no issue is observed when the poll
is omitted, because the writes complete before the next
write begins. But at high clock speeds the subsequent
writes would overlap and cause the operation to fail.
The status polls are done on the target for efficiency,
since the half-pages are very small.
Change-Id: Ia1e9b4a6a71930549b3d84a902744ce6e596301b
Signed-off-by: Jimmy <nhminus@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5598
Tested-by: jenkins
Reviewed-by: Jelle De Vleeschouwer
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andrzej Sierżęga <asier70@gmail.com>
stm32l4_work_area struct is shared between the loader and stm32l4x flash driver
'*wp' and '*rp' pointers' size is 4 bytes each since stm32l4x devices have
32-bit processors.
however when used in openocd code, their size depends on the host
if the host is 32-bit, then the size is 4 bytes each.
if the host is 64-bit, then the size is 8 bytes each.
to avoid this size difference, change their types depending on the
usage (pointers for the loader, and 32-bit integers in openocd code).
Change-Id: I0a3df4bb4bf872b01cdb9357eb28307868d7d469
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6556
Tested-by: jenkins
Reviewed-by: Yestin Sun <sunyi0804@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
switching to C loader instead of the assembly version will enhance readability
will reduce the maintenance effort.
besides the switch to C loader, we added a new parameters to the loader
like flash_word_size and flash_sr_bsy_mask in order to support properly
STM32U5x and STM32G0Bx/G0Cx in dual-bank mode.
Change-Id: I24cafc2ba637a065593a0506eae787b21080a0ba
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6109
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
