If max_length is equal or greater than cmdline length all trailing non-printable
characters are dropped. If max_length is 0 it should do the same.
This should also fix cmdline truncation if the last character is not '\0'.
Fixes#3469.
Previously, we checked only for the various SetLinkXYZ() calls on the Manager
object exposed on the bus if the specified interface is managed/unmanaged by
networkd (as we don't permit overriding DNS configuration via bus calls if
networkd owns the device), but the equivalent SetXYZ() calls on the Link object
did not have such a check. Fix that by moving the appropriate check into the
latter, as the former just calls that anyway.
Reloading or reexecuting PID 1 means the unit generators are rerun, which are
timed out at 90s. Make sure the method call asking for the reload is timed out
at twice that, so that the generators have 90s and the reload operation has 90s
too.
This reworks the daemon_reload() call in systemctl, and makes it exclusively
about reloading/reexecing. Previously it was used for other trivial method
calls too, which didn't really help readability. As the code paths are now
sufficiently different, split out the old code into a new function
trivial_method().
This call also does a similar change as
c8ad4efb277c3235d58789170af11bb3c847d655 but for the reload/reexec operation.
Fixes: #3353
For legacy commands such as /sbin/halt or /sbin/poweroff we support legacy
fallbacks that talk via traditional SysV way with PID 1 to issue the desired
operation. We do this on any kind of error if the primary method of operation
fails. When this is the case we suppress any error message that is normally
generated, in order to not confuse the user. When suppressing this log message,
don't suppress the original error code, because there's really no reason to.
This patch implements the new magic character '!'. By putting '!' in front
of a command, systemd executes it with full privileges ignoring paramters
such as User, Group, SupplementaryGroups, CapabilityBoundingSet,
AmbientCapabilities, SecureBits, SystemCallFilter, SELinuxContext,
AppArmorProfile, SmackProcessLabel, and RestrictAddressFamilies.
Fixes partially https://github.com/systemd/systemd/issues/3414
Related to https://github.com/coreos/rkt/issues/2482
Testing:
1. Create a user 'bob'
2. Create the unit file /etc/systemd/system/exec-perm.service
(You can use the example below)
3. sudo systemctl start ext-perm.service
4. Verify that the commands starting with '!' were not executed as bob,
4.1 Looking to the output of ls -l /tmp/exec-perm
4.2 Each file contains the result of the id command.
`````````````````````````````````````````````````````````````````
[Unit]
Description=ext-perm
[Service]
Type=oneshot
TimeoutStartSec=0
User=bob
ExecStartPre=!/usr/bin/sh -c "/usr/bin/rm /tmp/exec-perm*" ;
/usr/bin/sh -c "/usr/bin/id > /tmp/exec-perm-start-pre"
ExecStart=/usr/bin/sh -c "/usr/bin/id > /tmp/exec-perm-start" ;
!/usr/bin/sh -c "/usr/bin/id > /tmp/exec-perm-star-2"
ExecStartPost=/usr/bin/sh -c "/usr/bin/id > /tmp/exec-perm-start-post"
ExecReload=/usr/bin/sh -c "/usr/bin/id > /tmp/exec-perm-reload"
ExecStop=!/usr/bin/sh -c "/usr/bin/id > /tmp/exec-perm-stop"
ExecStopPost=/usr/bin/sh -c "/usr/bin/id > /tmp/exec-perm-stop-post"
[Install]
WantedBy=multi-user.target]
`````````````````````````````````````````````````````````````````
Since the introduction of the whitelist in 60-persistent-storage.rules
block device symlinks are no longer created for scm block devices.
Add scm to the whitelist.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
This the patch implements a notificaiton mechanism from the init process
in the container to systemd-nspawn.
The switch --notify-ready=yes configures systemd-nspawn to wait the "READY=1"
message from the init process in the container to send its own to systemd.
--notify-ready=no is equivalent to the previous behavior before this patch,
systemd-nspawn notifies systemd with a "READY=1" message when the container is
created. This notificaiton mechanism uses socket file with path relative to the contanier
"/run/systemd/nspawn/notify". The default values it --notify-ready=no.
It is also possible to configure this mechanism from the .nspawn files using
NotifyReady. This parameter takes the same options of the command line switch.
Before this patch, systemd-nspawn notifies "ready" after the inner child was created,
regardless the status of the service running inside it. Now, with --notify-ready=yes,
systemd-nspawn notifies when the service is ready. This is really useful when
there are dependencies between different contaniers.
Fixes https://github.com/systemd/systemd/issues/1369
Based on the work from https://github.com/systemd/systemd/pull/3022
Testing:
Boot a OS inside a container with systemd-nspawn.
Note: modify the commands accordingly with your filesystem.
1. Create a filesystem where you can boot an OS.
2. sudo systemd-nspawn -D ${HOME}/distros/fedora-23/ sh
2.1. Create the unit file /etc/systemd/system/sleep.service inside the container
(You can use the example below)
2.2. systemdctl enable sleep
2.3 exit
3. sudo systemd-run --service-type=notify --unit=notify-test
${HOME}/systemd/systemd-nspawn --notify-ready=yes
-D ${HOME}/distros/fedora-23/ -b
4. In a different shell run "systemctl status notify-test"
When using --notify-ready=yes the service status is "activating" for 20 seconds
before being set to "active (running)". Instead, using --notify-ready=no
the service status is marked "active (running)" quickly, without waiting for
the 20 seconds.
This patch was also test with --private-users=yes, you can test it just adding it
at the end of the command at point 3.
------ sleep.service ------
[Unit]
Description=sleep
After=network.target
[Service]
Type=oneshot
ExecStart=/bin/sleep 20
[Install]
WantedBy=multi-user.target
------------ end ------------
