IP27 configuration isn't the only NUMA system - it just happens to be
the currently only supported MIPS NUMA system. So move the necessary
options back into the main MIPS Kconfig file.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mark au1xxx_timer_setup() __init, just because it is. Get rid of
unneeded extern's (note that (*do_gettimeoffset)() is already declared by
<asm/time.c>) and an unused variable. Kill some whitespace...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The struct mips_fpu_soft_struct and mips_fpu_hard_struct are
completely same now and the kernel fpu emulator assumes that. This
patch unifies them to mips_fpu_struct and get rid of mips_fpu_union.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert sizeof/sizeof use to use of ARRAY_SIZE macro, and annotate
irqmap structures as __initdata.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I found that NPTL's pthread_cond_signal() does not work properly on
kernels compiled by gcc 4.1.x. I suppose inline asm for
__futex_atomic_op() was wrong. I suppose:
1. "=&r" constraint should be used for oldval.
2. Instead of "r" (uaddr), "=R" (*uaddr) for output and "R" (*uaddr)
for input should be used.
3. "memory" should be added to the clobber list.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Running a UP kernel on a bcm1480 board, I get nonsensical timing
results, like this:
release@unknown:~/tmp$ time ./a.out
real 0m22.906s
user 0m45.792s
sys 0m0.010s
According to my watch, this program took 23 seconds to run, so the real
time clock is OK. It is process accounting that is broken.
I tracked this down to a problem with the function
bcm1480_timer_interrupt in the file sibyte/bcm1480/time.c. This
function calls ll_timer_interrupt for cpu0, and ll_local_timer_interrupt
for all cpus. However, both of these functions do process accounting.
Thus processes running on cpu0 end up with doubled times. This is very
obvious in a UP kernel where all processes run on cpu0.
The correct way to do this is to only call ll_local_timer interrupt if
this is not cpu0. This can be seen in the mips-board/generic/time.c
file, and also in the sibyte/sb1250/time.c file, both of which handle
this correctly. I fixed the bcm1480/time.c file by copying over the
correct code from the sb1250/time.c file.
With this fix, I now get sensible results.
release@unknown:~/tmp$ time ./a.out
real 0m22.903s
user 0m22.894s
sys 0m0.006s
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle
Rodolfo Giometti
Yoichi Yuasa
Sergei Shtylyov
Thiemo Seufer
Atsushi Nemoto
Mark.Zhan
Herbert Valerio Riedel
[MIPS] James E Wilson