Sudarsana Reddy Kalluru says:
====================
qed*: Add support for pcie advanced error recovery.
The patch series adds qed/qede driver changes for PCIe Advanced Error
Recovery (AER) support.
Patch (1) adds qed changes to enable the device to send error messages
to root port when detected.
Patch (2) adds qede support for handling the detected errors (AERs).
Changes from previous version:
-------------------------------
v2: use pci_num_vf() instead of caching the value in edev.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The error recovery is handled by management firmware (MFW) with the help of
qed/qede drivers. Upon detecting the errors, driver informs MFW about this
event which in turn starts a recovery process. MFW sends ERROR_RECOVERY
notification to the driver which performs the required cleanup/recovery
from the driver side.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gro_cells lib is used by different encapsulating netdevices, such as
geneve, macsec, vxlan etc. to speed up decapsulated traffic processing.
CPU tag is a sort of "encapsulation", and we can use the same mechs to
greatly improve overall DSA performance.
skbs are passed to the GRO layer after removing CPU tags, so we don't
need any new packet offload types as it was firstly proposed by me in
the first GRO-over-DSA variant [1].
The size of struct gro_cells is sizeof(void *), so hot struct
dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields
remain in one 32-byte cacheline.
The other positive side effect is that drivers for network devices
that can be shipped as CPU ports of DSA-driven switches can now use
napi_gro_frags() to pass skbs to kernel. Packets built that way are
completely non-linear and are likely being dropped without GRO.
This was tested on to-be-mainlined-soon Ethernet driver that uses
napi_gro_frags(), and the overall performance was on par with the
variant from [1], sometimes even better due to minimal overhead.
net.core.gro_normal_batch tuning may help to push it to the limit
on particular setups and platforms.
iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup
on 1.2 GHz MIPS board:
5.7-rc2 baseline:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender
[ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver
Iface RX packets TX packets
eth0 7097731 7097702
port0 426050 6671829
port1 6671681 425862
port1.218 6671677 425851
With this patch:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender
[ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver
Iface RX packets TX packets
eth0 9474792 9474777
port0 455200 353288
port1 9019592 455035
port1.218 353144 455024
v2:
- Add some performance examples in the commit message;
- No functional changes.
[1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/
Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4862 5.5.3 e) prevents received Router Advertisements from reducing
the Valid Lifetime of configured addresses to less than two hours, thus
preventing hosts from reacting to the information provided by a router
that has positive knowledge that a prefix has become invalid.
This patch makes hosts honor all Valid Lifetime values, as per
draft-gont-6man-slaac-renum-06, Section 4.2. This is meant to help
mitigate the problem discussed in draft-ietf-v6ops-slaac-renum.
Note: Attacks aiming at disabling an advertised prefix via a Valid
Lifetime of 0 are not really more harmful than other attacks
that can be performed via forged RA messages, such as those
aiming at completely disabling a next-hop router via an RA that
advertises a Router Lifetime of 0, or performing a Denial of
Service (DoS) attack by advertising illegitimate prefixes via
forged PIOs. In scenarios where RA-based attacks are of concern,
proper mitigations such as RA-Guard [RFC6105] [RFC7113] should
be implemented.
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei says:
====================
dpaa2-eth: add support for xdp bulk enqueue
The first patch moves the DEV_MAP_BULK_SIZE macro into the xdp.h header
file so that drivers can take advantage of it and use it.
The following 3 patches are there to setup the scene for using the bulk
enqueue feature. First of all, the prototype of the enqueue function is
changed so that it returns the number of enqueued frames. Second, the
bulk enqueue interface is used but without any functional changes, still
one frame at a time is enqueued. Third, the .ndo_xdp_xmit callback is
split into two stages, create all FDs for the xdp_frames received and
then enqueue them.
The last patch of the series builds on top of the others and instead of
issuing an enqueue operation for each FD it issues a bulk enqueue call
for as many frames as possible. This is repeated until all frames are
enqueued or the maximum number of retries is hit. We do not use the
XDP_XMIT_FLUSH flag since the architecture is not capable to store all
frames dequeued in a NAPI cycle, instead we send out right away all
frames received in a .ndo_xdp_xmit call.
Changes in v2:
- statically allocate an array of dpaa2_fd by frame queue
- use the DEV_MAP_BULK_SIZE as the maximum number of xdp_frames
received in .ndo_xdp_xmit()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the bulk enqueue feature in .ndo_xdp_xmit.
We cannot use the XDP_XMIT_FLUSH since the architecture is not capable
to store all the frames dequeued in a NAPI cycle so we instead are
enqueueing all the frames received in a ndo_xdp_xmit call right away.
After setting up all FDs for the xdp_frames received, enqueue multiple
frames at a time until all are sent or the maximum number of retries is
hit.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having a function that both creates a frame descriptor from
an xdp_frame and enqueues it, split this into two stages.
Add the dpaa2_eth_xdp_create_fd that just transforms an xdp_frame into a
FD while the actual enqueue callback is called directly from the ndo for
each frame.
This is particulary useful in conjunction with bulk enqueue.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dpaa2-eth driver to use the bulk enqueue function introduced
with the change to QBMAN ring mode. At the moment, no functional changes
are made but rather the driver just transitions to the new interface
while still enqueuing just one frame at a time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enqueue dpaa2-eth callback now returns the number of successfully
enqueued frames. This is a preliminary patch necessary for adding
support for bulk ring mode enqueue.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the DEV_MAP_BULK_SIZE macro to the header file so that drivers
can directly use it as the maximum number of xdp_frames received in the
.ndo_xdp_xmit() callback.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nodad when adding IPv6 addresses and remove the sleep.
A recent change to iproute2 moved the 'pref medium' to the prefix
(where it belongs). Change the expected route check to strip
'pref medium' to be compatible with old and new iproute2.
Add IPv4 runtime test with an IPv6 address as the gateway in
the default route.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
Add selftests for pedit ex munge ip6 dsfield
Patch #1 extends the existing generic forwarding selftests to cover pedit
ex munge ip6 traffic_class as well. Patch #2 adds TDC test coverage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a self-test for the IPv6 dsfield munge that iproute2 will support.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the pedit_dsfield forwarding selftest with coverage of "pedit ex
munge ip6 dsfield set".
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel says:
====================
add TJA1102 support
changes v5:
- rename __of_mdiobus_register_phy() to of_mdiobus_phy_device_register()
changes v4:
- remove unused phy_id variable
changes v3:
- export part of of_mdiobus_register_phy() and reuse it in tja11xx
driver
- coding style fixes
changes v2:
- use .match_phy_device
- add irq support
- add add delayed registration for PHY1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1
having no ID. On one hand it is possible to for PHY detection by
compatible, on other hand we should be able to reset complete chip
before PHY1 configured it, and we need to define dependencies for proper
power management.
We can solve it by defining PHY1 as child of PHY0:
tja1102_phy0: ethernet-phy@4 {
reg = <0x4>;
interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
reset-assert-us = <20>;
reset-deassert-us = <2000>;
tja1102_phy1: ethernet-phy@5 {
reg = <0x5>;
interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
};
};
The PHY1 should be a subnode of PHY0 and registered only after PHY0 was
completely reset and initialized.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be needed in tja11xx driver for secondary PHY
support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable.
Both PHYs are similar but have different amount of functionality. For
example PHY 1 has no PHY ID and no health monitor.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for following phy-modes: rgmii, rgmii-id, rgmii-txid, rgmii-rxid.
This PHY has an internal RX delay of 1.2ns and no delay for TX.
The pad skew registers allow to set the total TX delay to max 1.38ns and
the total RX delay to max of 2.58ns (configurable 1.38ns + build in
1.2ns) and a minimal delay of 0ns.
According to the RGMII v1.3 specification the delay provided by PCB traces
should be between 1.5ns and 2.0ns. The RGMII v2.0 allows to provide this
delay by MAC or PHY. So, we configure this PHY to the best values we can
get by this HW: TX delay to 1.38ns (max supported value) and RX delay to
1.80ns (best calculated delay)
The phy-modes can still be fine tuned/overwritten by *-skew-ps
device tree properties described in:
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
net/caif/caif_dev.c:410:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:445:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:145:1-12: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:223:1-12: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan_hash_lookup() uses list_for_each_entry_rcu() for traversing
should either under RCU in fast path or the protection of rtnl_mutex.
In the case of holding RTNL, we should add the corresponding lockdep
expression to silence the following false-positive warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc1-next-20200416-00003-ga3b8d28bc #1 Not tainted
-----------------------------
drivers/net/macvlan.c:126 RCU-list traversed in non-reader section!!
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Sudarsana Reddy Kalluru
Alexander Lobakin
Fernando Gont
Ioana Ciornei
David Ahern
Petr Machata
Oleksij Rempel
Tang Bin
Jason Yan
Chuah, Kim Tatt
Wei Yongjun