Setting the vibrator enable_mask is not implemented correctly:
For regmap_update_bits(map, reg, mask, val) we give in either
regs->enable_mask or 0 (= no-op) as mask and "val" as value.
But "val" actually refers to the vibrator voltage control register,
which has nothing to do with the enable_mask.
So we usually end up doing nothing when we really wanted
to enable the vibrator.
We want to set or clear the enable_mask (to enable/disable the vibrator).
Therefore, change the call to always modify the enable_mask
and set the bits only if we want to enable the vibrator.
Fixes: d4c7c5c96c ("Input: pm8xxx-vib - handle separate enable register")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200114183442.45720-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 99f83c9c9a ("[PATCH] USB: add driver for Keyspan Digital Remote")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 2.6.13
Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the onkey driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.
This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.
This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 162f98dea4 ("Input: gtco - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-5-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-3-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.
Fixes: e28d0c9cd3 ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We observed a large(order-3) allocation in evdev_open() and it may
cause an OOM kernel panic in kzalloc(), before we getting to the
vzalloc() fallback.
Fix it by converting kzalloc()/vzalloc() to kvzalloc() to avoid the
OOM killer logic as we have a vmalloc fallback.
InputReader invoked oom-killer: gfp_mask=0x240c2c0
(GFP_KERNEL|__GFP_NOWARN|__GFP_COMP|__GFP_ZERO), nodemask=0, order=3,
oom_score_adj=-900
...
(dump_backtrace) from (show_stack+0x18/0x1c)
(show_stack) from (dump_stack+0x94/0xa8)
(dump_stack) from (dump_header+0x7c/0xe4)
(dump_header) from (out_of_memory+0x334/0x348)
(out_of_memory) from (__alloc_pages_nodemask+0xe9c/0xeb8)
(__alloc_pages_nodemask) from (kmalloc_order_trace+0x34/0x128)
(kmalloc_order_trace) from (__kmalloc+0x258/0x36c)
(__kmalloc) from (evdev_open+0x5c/0x17c)
(evdev_open) from (chrdev_open+0x100/0x204)
(chrdev_open) from (do_dentry_open+0x21c/0x354)
(do_dentry_open) from (vfs_open+0x58/0x84)
(vfs_open) from (path_openat+0x640/0xc98)
(path_openat) from (do_filp_open+0x78/0x11c)
(do_filp_open) from (do_sys_open+0x130/0x244)
(do_sys_open) from (SyS_openat+0x14/0x18)
(SyS_openat) from (__sys_trace_return+0x0/0x10)
...
Normal: 12488*4kB (UMEH) 6984*8kB (UMEH) 2101*16kB (UMEH) 0*32kB
0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 139440kB
HighMem: 206*4kB (H) 131*8kB (H) 42*16kB (H) 2*32kB (H) 0*64kB
0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2608kB
...
Kernel panic - not syncing: Out of memory and no killable processes...
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Just a few small fixups here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_sc_key - only take the valid data from SCU firmware as key state
Input: add safety guards to input_set_keycode()
Input: input_event - fix struct padding on sparc64
Input: uinput - always report EPOLLOUT
When reading key state from SCU, the response data from SCU firmware
is 4 bytes due to MU message protocol, but ONLY the first byte is the
key state, other 3 bytes could be some dirty data, so we should ONLY
take the first byte as key state to avoid reporting incorrect state.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Fixes: 688f1dfb69 ("Input: keyboard - imx_sc: Add i.MX system controller key support")
Link: https://lore.kernel.org/r/1576202909-1661-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Going through all uses of timeval, I noticed that we screwed up
input_event in the previous attempts to fix it:
The time fields now match between kernel and user space, but all following
fields are in the wrong place.
Add the required padding that is implied by the glibc timeval definition
to fix the layout, and use a struct initializer to avoid leaking kernel
stack data.
Fixes: 141e5dcaa7 ("Input: input_event - fix the CONFIG_SPARC64 mixup")
Fixes: 2e746942eb ("Input: input_event - provide override for sparc64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191213204936.3643476-2-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
- fixups for Synaptics RMI4 driver
- a quirk for Goodinx touchscreen on Teclast tablet
- a new keycode definition for activating privacy screen feature found
on a few "enterprise" laptops
- updates to snvs_pwrkey driver
- polling uinput device for writing (which is always allowed) now works
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
Input: goodix - add upside-down quirk for Teclast X89 tablet
Input: add privacy screen toggle keycode
Input: uinput - fix returning EPOLLOUT from uinput_poll
Input: snvs_pwrkey - remove gratuitous NULL initializers
Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q
This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.
The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.
I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.
It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.
With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/8dd22e21-4933-8e9c-a696-d281872c8de7@xs4all.nl
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.
The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.
Fixes: 363c53875a (Input: synaptics-rmi4 - avoid processing unknown IRQs)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191129133514.23224-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
