Currently the link state is initialized to "up" when the phy_device is
being created. This is not consistent with the phy state being
initialized to PHY_DOWN.
Usually this doen't do any harm because the link state is updated
once the PHY reaches state PHY_AN. However e.g. if a LAN port isn't
used and the PHY remains down this inconsistency remains and calls
to functions like phy_print_status() give false results.
Therefore change the initialization to link being down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-03-12
This series contains updates to ixgbe and ixgbevf only.
Shannon Nelson provides three fixes to the ipsec portion of ixgbe. Make
sure we are using 128-bit authentication, since it is the only size
supported for hardware offload. Fixed the transmit trailer length
calculation for ipsec by finding the padding value and adding it to the
authentication length, then save it off so that we can put it in the
transmit descriptor to tell the device where to stop the checksum
calculation. Lastly, cleaned up useless and dead code.
Tonghao Zhang adds a ethtool stat for receive length errors, since the
driver was already collecting this counter.
Arnd Bergmann fixed a warning about an used variable by "rephrasing" the
code so that the compiler can see the use of the variable in question.
Paul fixes an issue where "HIDE_VLAN" was being cleared on VF reset, so
ensure to set "HIDE_VLAN" when port VLAN is enabled after a VF reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new ixgbevf_set_rx_buffer_len() function causes a harmless warnings
in configurations with large page size:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c: In function 'ixgbevf_set_rx_buffer_len':
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1758:15: error: unused variable 'max_frame' [-Werror=unused-variable]
This rephrases the code so that the compiler can see the use of that
variable, making it slightly easier to read in the process.
Fixes: f15c5ba5b6 ("ixgbevf: add support for using order 1 pages to receive large frames")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up the Tx trailer length calculation. We can't believe the
trailer len from the xstate information because it was calculated
before the packet was put together and padding added. This bit
of code finds the padding value in the trailer, adds it to the
authentication length, and saves it so later we can put it into
the Tx descriptor to tell the device where to stop the checksum
calculation.
Fixes: 5925947047 ("ixgbe: process the Tx ipsec offload")
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:371:5: warning:
symbol 'mlxsw_sp_kvdl_single_occ_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:384:5: warning:
symbol 'mlxsw_sp_kvdl_chunks_occ_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:397:5: warning:
symbol 'mlxsw_sp_kvdl_large_chunks_occ_get' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as LRO, hardware GRO cannot be enabled with RX-FCS.
When both are requested, hardware GRO will be dropped.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a VLA[1] by using a real constant expression instead of a variable.
The compiler should be able to optimize the original code and avoid using
an actual VLA. Anyway this change is useful because it will avoid a false
positive with -Wvla, it might also help the compiler generating better
code.
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Salvatore Mesoraca <s.mesoraca16@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions lan743x_csr_read and lan743x_csr_read are local to the source
and do not need to be in global scope, so make them static.
Cleans up sparse warning:
drivers/net/ethernet/microchip/lan743x_main.c:56:5: warning: symbol
lan743x_csr_read' was not declared. Should it be static?
drivers/net/ethernet/microchip/lan743x_main.c:61:6: warning: symbol
'lan743x_csr_write' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function lan743x_phy_init assigns pointer 'netdev' but this is never read
and hence it can be removed. The return error code handling can also be
cleaned up to remove the variable 'ret'.
Function lan743x_phy_link_status_change assigns pointer 'phy' twice and
this is never read, so it also can be removed.
Finally, function lan743x_tx_napi_poll initializes pointer 'adapter'
and then re-assigns the same value into this pointer a little later on
so this second assignment is redundant and can be also removed.
Cleans up clang warnings:
drivers/net/ethernet/microchip/lan743x_main.c:951:2: warning: Value
stored to 'netdev' is never read
drivers/net/ethernet/microchip/lan743x_main.c:971:3: warning: Value
stored to 'phy' is never read
drivers/net/ethernet/microchip/lan743x_main.c:1583:26: warning: Value
stored to 'adapter' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable sg_off is assigned a value but it is never read, hence it is
redundant and can be removed.
Cleans up clang warning:
net/rds/message.c:373:2: warning: Value stored to 'sg_off' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Removing dependency of mlxsw on GRE
Petr says:
mlxsw_spectrum supports offloading of a tc action mirred egress mirror
to a gretap or ip6gretap netdevice, which necessitates calls to
functions defined in ip_gre, ip6_gre and ip6_tunnel modules. Previously
this was enabled by introducing a hard dependency of MLXSW_SPECTRUM on
NET_IPGRE and IPV6_GRE. However the rest of mlxsw is careful about
picking which modules are absolutely required, and therefore the better
approach is to make mlxsw_spectrum tolerant of absence of one or both of
the GRE flavors.
One way this might be resolved is by keeping the code in mlxsw_spectrum
intact, and defining defaults for functions that mlxsw_spectrum depends
on. The downsides are that other modules end up littered with these
do-nothing defaults; that the driver ends up carrying quite a bit of
dead code; and that the driver ends up having to explicitly depend on
IPV6_TUNNEL to prevent configurations where mlxsw_spectrum is compiled
in and and ip6_tunnel is a module, something that it currently can treat
as an implementation detail of the IPV6_GRE dependency.
Alternatively, the driver should just bite the bullet and ifdef-out the
code that handles configurations that are not supported. Since that's
what we are doing for IPv6 dependency, let's do the same for the GRE
flavors.
Patch #1 introduces a wrapper function for determining the value of
ipv6.sysctl.multipath_hash_policy, which defaults to 0 on non-IPv6
builds. That function is then used from spectrum_router.c, instead of
the direct variable reference that was introduced there during the short
window when the Spectrum driver had a hard dependency on IPv6.
Patch #2 moves one function to keep together in one block all the
callbacks for handling (IPv4) gretap mirroring.
Patch #3 then introduces the ifdefs to hide the irrelevant code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw_spectrum supports offloading of a tc action mirred egress mirror
to a gretap or an ip6gretap netdevice, which necessitates calls to
functions defined in ip_gre, ip6_gre and ip6_tunnel modules. Previously
this was enabled by introducing a hard dependency of MLXSW_SPECTRUM on
NET_IPGRE and IPV6_GRE. However the rest of mlxsw is careful about
picking which modules are absolutely required, and therefore the better
approach is to make mlxsw_spectrum tolerant of absence of one or both of
the GRE flavors.
Hence rework the NET_IPGRE and IPV6_GRE dependencies to just guard
matching modularity, and hide the corresponding code in spectrum_span.c
in an #if IS_ENABLED. Mark mlxsw_sp_span_entry_tunnel_parms_common as
maybe unused, to muffle warnings if neither GRE flavor is selected,
which seems cleaner than introducing a composite #if.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the function next to the rest of gretap4 functions. Thus the
generic functions shared between gretap4 and gretap6 are in one block at
the beginning, followed by a gretap4 block, followed by a gretap6 block.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to abstract away access to the
ipv6.sysctl.multipath_hash_policy variable, which is not available on
systems compiled without IPv6 support, introduce a wrapper function
ip6_multipath_hash_policy() that falls back to 0 on non-IPv6 systems.
Use this wrapper from mlxsw/spectrum_router instead of a direct
reference.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check firmware capabilities before setting ethtool
link mode mask, also add few missing speeds.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
50Gbps is a supported speed, Stop reporting it as
unsupported speed.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
