So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.
The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial core does not use tty_port_open() or tty_port_close(); serial
core defines and extends it's own tty open() and close() methods
(uart_open() and uart_close(), respectively).
Remove the tty_port activate() and shutdown() initializations, and
the uart_port_activate() function, which is never called.
NB: uart_port_shutdown() is used by uart_close() => uart_shutdown()
call chain (but not via the tty_port methods).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_close() runs in non-atomic context only; use
spin_lock/unlock_irq instead of saving the interrupt state (which
== on).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "ti,dra742-uart" to the compatible list so the driver
workaround for UART module disable errata is enabled.
This does not break backward compatibility as existing DTBs
should continue to work with newer kernels albeit without the
capability to idle the UART module when DMA is used.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.
Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When system goes into low power states like SUSPEND_MEM and
HIBERNATION, the hardware IP block may be powered off to reduce
the power consumption. This power down may cause problems on
some imx platforms, because the hardware settings are reset to
its power on default values which may differ from the ones when
it power off. This patch added the dev_pm_ops and implemented
two callbacks: suspend_noirq and resume_noirq, which will save
the necessory hardware parameters right before power down and
recover them before system uses the hardware.
Because added the dev_pm_ops, the old suspend/resume callbacks
under platform_driver will not be called any more. Changed their
prototypes and moved those two callbacks into dev_pm_ops too.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RS485 control for Fintek F81504/508/512
F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.
When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.
When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.
When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.
We will force 0x01 on pci_fintek_setup().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other serial driver work wants to build on patches now in 4.2-rc4 so
merge the branch so this can properly happen.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull perf fix from Thomas Gleixner:
"A single fix for the intel cqm perf facility to prevent IPIs from
interrupt context"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/cqm: Return cached counter value from IRQ context
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- the manual revert of the SYSCALL32 changes which caused a
regression
- a fix for the MPX vma handling
- three fixes for the ioremap 'is ram' checks.
- PAT warning fixes
- a trivial fix for the size calculation of TLB tracepoints
- handle old EFI structures gracefully
This also contains a PAT fix from Jan plus a revert thereof. Toshi
explained why the code is correct"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Revert 'Adjust default caching mode translation tables'
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
x86/mm: Fix newly introduced printk format warnings
mm: Fix bugs in region_is_ram()
x86/mm: Remove region_is_ram() call from ioremap
x86/mm: Move warning from __ioremap_check_ram() to the call site
x86/mm/pat, drivers/media/ivtv: Move the PAT warning and replace WARN() with pr_warn()
x86/mm/pat, drivers/infiniband/ipath: Replace WARN() with pr_warn()
x86/mm/pat: Adjust default caching mode translation tables
x86/fpu: Disable dependent CPU features on "noxsave"
x86/mpx: Do not set ->vm_ops on MPX VMAs
x86/mm: Add parenthesis for TLB tracepoint size calculation
efi: Handle memory error structures produced based on old versions of standard
Toshi explains:
"No, the default values need to be set to the fallback types,
i.e. minimal supported mode. For WC and WT, UC is the fallback type.
When PAT is disabled, pat_init() does update the tables below to
enable WT per the default BIOS setup. However, when PAT is enabled,
but CPU has PAT -errata, WT falls back to UC per the default values."
Revert: ca1fec58bc 'x86/mm/pat: Adjust default caching mode translation tables'
Requested-by: Toshi Kani <toshi.kani@hp.com>
Cc: Jan Beulich <jbeulich@suse.de>
Link: http://lkml.kernel.org/r/1437577776.3214.252.camel@hp.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull USB fixes from Greg KH:
"Here's a few USB and PHY fixes for 4.2-rc4.
Nothing major, the shortlog has the full details.
All of these have been in linux-next successfully"
* tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
USB: OHCI: fix bad #define in ohci-tmio.c
cdc-acm: Destroy acm_minors IDR on module exit
usb-storage: Add ignore-device quirk for gm12u320 based usb mini projectors
usb-storage: ignore ZTE MF 823 card reader in mode 0x1225
USB: OHCI: Fix race between ED unlink and URB submission
usb: core: lpm: set lpm_capable for root hub device
xhci: do not report PLC when link is in internal resume state
xhci: prevent bus_suspend if SS port resuming in phase 1
xhci: report U3 when link is in resume state
xhci: Calculate old endpoints correctly on device reset
usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function
xhci: Workaround to get D3 working in Intel xHCI
xhci: call BIOS workaround to enable runtime suspend on Intel Braswell
usb: dwc3: Reset the transfer resource index on SET_INTERFACE
usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU
usb: gadget: mv_udc_core: fix phy_regs I/O memory leak
usb: ulpi: ulpi_init should be executed in subsys_initcall
phy: berlin-usb: fix divider for BG2
phy: berlin-usb: fix divider for BG2CD
phy/pxa: add HAS_IOMEM dependency
...
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small serial and tty fixes for reported issues.
All have been in linux-next successfully"
* tag 'tty-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: vt: Fix !TASK_RUNNING diagnostic warning from paste_selection()
serial: core: Fix crashes while echoing when closing
m32r: Add ioreadXX/iowriteXX big-endian mmio accessors
Revert "serial: imx: initialized DMA w/o HW flow enabled"
sc16is7xx: fix FIFO address of secondary UART
sc16is7xx: fix Kconfig dependencies
serial: etraxfs-uart: Fix release etraxfs_uart_ports
tty/vt: Fix the memory leak in visual_init
serial: amba-pl011: Fix devm_ioremap_resource return value check
n_tty: signal and flush atomically
Pull staging driver fixes from Greg KH:
"Here are a number of iio and staging driver fixes for reported issues
for 4.2-rc4.
All have been in linux-next for a while with no problems"
* tag 'staging-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
iio:light:stk3310: make endianness independent of host
iio:light:stk3310: move device register to end of probe
iio: mma8452: use iio event type IIO_EV_TYPE_MAG
iio: mcp320x: Fix NULL pointer dereference
iio: adc: vf610: fix the adc register read fail issue
iio: mlx96014: Replace offset sign
iio: magnetometer: mmc35240: fix SET/RESET sequence
iio: magnetometer: mmc35240: Fix SET/RESET mask
iio: magnetometer: mmc35240: Fix crash in pm suspend
iio:magnetometer:bmc150_magn: output intended variable
iio:magnetometer:bmc150_magn: add regmap dependency
staging: vt6656: check ieee80211_bss_conf bssid not NULL
staging: vt6655: check ieee80211_bss_conf bssid not NULL
iio: tmp006: Check channel info on write
iio: sx9500: Add missing init in sx9500_buffer_pre{en,dis}able()
iio:light:ltr501: fix regmap dependency
iio:light:ltr501: fix variable in ltr501_init
iio: sx9500: fix bug in compensation code
iio: sx9500: rework error handling of raw readings
iio: magnetometer: mmc35240: fix available sampling frequencies
...
