There are set of configurations to be done at MCS port level like
bringing port out of reset, making port as operational or bypass.
This patch adds all the port related mailbox message handlers
so that AF consumers can use them.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K-B and CNF10K-B has macsec block(MCS) to encrypt and
decrypt packets at MAC level. This block is a global resource
with hardware resources like SecYs, SCs and SAs and is in
between NIX block and RPM LMAC. CN10K-B silicon has only one MCS
block which receives packets from all LMACS whereas CNF10K-B has
seven MCS blocks for seven LMACs. Both MCS blocks are
similar in operation except for few register offsets and some
configurations require writing to different registers. Those
differences between IPs are handled using separate ops.
This patch adds basic driver and does the initial hardware
calibration and parser configuration.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur says:
====================
net: lan966x: Add police and mirror using tc-matchall
Add tc-matchall classifier offload support both for ingress and egress.
For this add support for the port police and port mirroring action support.
Port police can happen only on ingress while port mirroring is supported
both on ingress and egress
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for port mirroring. It is possible to mirror only one port
at a time and it is possible to have both ingress and egress mirroring.
Frames injected by the CPU don't get egress mirrored because they are
bypassing the analyzer module.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for port police. It is possible to police only on the
ingress side. To be able to add police support also it was required to
add tc-matchall classifier offload support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DECnet was removed by commit 1202cdd665 ("Remove DECnet support from
kernel"). Let's also revome its flow structure.
Compile-tested only (allmodconfig).
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current GRO stack only supports incoming packets containing
one frame/MSS.
This patch changes GRO to accept packets that are already GRO.
HW-GRO (aka RSC for some vendors) is very often limited in presence
of interleaved packets. Linux SW GRO stack can complete the job
and provide larger GRO packets, thus reducing rate of ACK packets
and cpu overhead.
This also means BIG TCP can still be used, even if HW-GRO/RSC was
able to cook ~64 KB GRO packets.
v2: fix logic in tcp_gro_receive()
Only support TCP for the moment (Paolo)
Co-Developed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Coco Li <lixiaoyan@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: Fastclose edge cases and error handling
MPTCP has existing code to use the MP_FASTCLOSE option header, which
works like a RST for the MPTCP-level connection (regular RSTs only
affect specific subflows in MPTCP). This series has some improvements
for fastclose.
Patch 1 aligns fastclose socket error handling with TCP RST behavior on
TCP sockets.
Patch 2 adds use of MP_FASTCLOSE in some more edge cases, like file
descriptor close, FIN_WAIT timeout, and when the socket has unread data.
Patch 3 updates the fastclose self tests.
Patch 4 does not change any code, just fixes some outdated comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPTCP data path is quite complex and hard to understend even
without some foggy comments referring to modified code and/or
completely misleading from the beginning.
Update a few of them to more accurately describing the current
status.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patches, the MPTCP protocol can generate
fast-closes on both ends of the connection. Rework the relevant
test-case to carefully trigger the fast-close code-path on a
single end at the time, while ensuring than a predictable amount
of data is spooled on both ends.
Additionally add another test-cases for the passive socket
fast-close.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daire reported a user-space application hang-up when the
peer is forcibly closed before the data transfer completion.
The relevant application expects the peer to either
do an application-level clean shutdown or a transport-level
connection reset.
We can accommodate a such user by extending the fastclose
usage: at fd close time, if the msk socket has some unread
data, and at FIN_WAIT timeout.
Note that at MPTCP close time we must ensure that the TCP
subflows will reset: set the linger socket option to a suitable
value.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an mptcp socket is closed due to an incoming FASTCLOSE
option, so specific sk_err is set and later syscall will
fail usually with EPIPE.
Align the current fastclose error handling with TCP reset,
properly setting the socket error according to the current
msk state and propagating such error.
Additionally sendmsg() is currently not handling properly
the sk_err, always returning EPIPE.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún says:
====================
RollBall / Hilink / Turris 10G copper SFP support
I am resurrecting my attempt to add support for RollBall / Hilink /
Turris 10G copper SFPs modules.
The modules contain Marvell 88X3310 PHY, which can communicate with
the system via sgmii, 2500base-x, 5gbase-r, 10gbase-r or usxgmii mode.
Some of the patches I've taken from Russell King's net-queue [1]
(with some rebasing).
The important change from my previous attempts are:
- I am including the changes needed to phylink and marvell10g driver,
so that the 88X3310 PHY is configured to use PHY modes supported by
the host (the PHY defaults to use 10gbase-r only on host's side)
- I have changed the patch that informs phylib about the interfaces
supported by the host (patch 5 of this series): it now fills in the
phydev->host_interfaces member only when connecting a PHY that is
inside a SFP module. This may change in the future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for multigig copper SFP modules from RollBall/Hilink.
These modules have a specific way to access clause 45 registers of the
internal PHY.
We also need to wait at least 22 seconds after deasserting TX disable
before accessing the PHY. The code waits for 25 seconds just to be sure.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some multigig SFPs from RollBall and Hilink do not expose functional
MDIO access to the internal PHY of the SFP via I2C address 0x56
(although there seems to be read-only clause 22 access on this address).
Instead these SFPs PHY can be accessed via I2C via the SFP Enhanced
Digital Diagnostic Interface - I2C address 0x51. The SFP_PAGE has to be
selected to 3 and the password must be filled with 0xff bytes for this
PHY communication to work.
This extends the mdio-i2c driver to support this protocol by adding a
special parameter to mdio_i2c_alloc function via which this RollBall
protocol can be selected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of configuring the I2C mdiobus when SFP driver is probed,
create/destroy the mdiobus before the PHY is probed for/after it is
released.
This way we can tell the mdio-i2c code which protocol to use for each
SFP transceiver.
Move the code that determines MDIO I2C protocol from
sfp_sm_probe_for_phy() to sfp_sm_mod_probe(), where most of the SFP ID
parsing is done. Don't allocate I2C bus if no PHY is expected.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macros SFP_QUIRK(), SFP_QUIRK_M() and SFP_QUIRK_F() for defining SFP
quirk table entries. Use them to deduplicate the code a little bit.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFPs may contain an internal PHY which may in some cases want to
connect with the host interface in 1000base-x/2500base-x mode.
Do not fail if such PHY is being attached in one of these PHY interface
modes.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select the host interface configuration according to the capabilities of
the host if the host provided them. This is currently provided only when
connecting PHY that is inside a SFP.
The PHY supports several configurations of host communication:
- always communicate with host in 10gbase-r, even if copper speed is
lower (rate matching mode),
- the same as above but use xaui/rxaui instead of 10gbase-r,
- switch host SerDes mode between 10gbase-r, 5gbase-r, 2500base-x and
sgmii according to copper speed,
- the same as above but use xaui/rxaui instead of 10gbase-r.
This mode of host communication, called MACTYPE, is by default selected
by strapping pins, but it can be changed in software.
This adds support for selecting this mode according to which modes are
supported by the host.
This allows the kernel to:
- support SFP modules with 88X33X0 or 88E21X0 inside them
Note: we use mv3310_select_mactype() for both 88X3310 and 88X3340,
although 88X3340 does not support XAUI. This is not a problem because
88X3340 does not declare XAUI in it's supported_interfaces, and so this
function will never choose that MACTYPE.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[ rebase, updated, also added support for 88E21X0 ]
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some register definitions were defined with spaces used for indentation.
Change them to tabs.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the supported PHY interface types to phylib if the PHY we are
connecting is inside a SFP, so that the PHY driver can select an
appropriate host configuration mode for their interface according to
the host capabilities.
For example the Marvell 88X3310 PHY inside RollBall SFP modules
defaults to 10gbase-r mode on host's side, and the marvell10g
driver currently does not change this setting. But a host may not
support 10gbase-r. For example Turris Omnia only supports sgmii,
1000base-x and 2500base-x modes. The PHY can be configured to use
those modes, but in order for the PHY driver to do that, it needs
to know which modes are supported.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink_sfp_config() now only deals with configuring the MAC for a
SFP containing a PHY. Rename it to be specific.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where a MAC provides a phy_interface_t bitmap, use these bitmaps to
select the operating interface mode for optical SFP modules, rather
than using the linkmode bitmaps.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently parse the SFP EEPROM to a bitmap of ethtool link modes,
and then attempt to convert the link modes to a PHY interface mode.
While this works at present, there are cases where this is sub-optimal.
For example, where a module can operate with several different PHY
interface modes.
To start addressing this, arrange for the SFP EEPROM parsing to also
provide a bitmap of the possible PHY interface modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geetha sowjanya
David S. Miller
Horatiu Vultur
Shenwei Wang
Guillaume Nault
Coco Li
Paolo Abeni
Marek Behún
Russell King