Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7df ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2020-03-11
please apply the following patch series for qeth to netdev's net tree.
Just one fix to get the RX buffer pool resizing right, with two
preparatory cleanups.
This is on the larger side given where we are in the -rc cycle, but a
big chunk of the delta is just refactoring to make the fix look nice.
I intentionally split these off from yesterday's series. No objections
if you'd rather punt them to net-next, the series should apply cleanly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer pool is allocated in qeth_alloc_qdio_queues().
A subsequent pool resizing is then handled in a very simple way:
first free the current pool, then allocate a new pool of the requested
size.
There's two ways where this can go wrong:
1. if the resize action happens _before_ the initial pool was allocated,
then a subsequent initialization will call qeth_alloc_qdio_queues()
and fill the pool with a second(!) set of pages. We consume twice the
planned amount of memory.
This is easy to fix - just skip the resizing if the queues haven't
been allocated yet.
2. if the initial pool was created by qeth_alloc_qdio_queues() but a
subsequent resizing fails, then the device has no(!) RX buffer pool.
The next initialization will _not_ call qeth_alloc_qdio_queues(), and
attempting to back the RX buffers with pages in
qeth_init_qdio_queues() will fail.
Not very difficult to fix either - instead of re-allocating the whole
pool, just allocate/free as many entries to match the desired size.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for a subsequent fix, split out helpers to allocate/free
individual pool entries.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer elements are always backed with full pages, reflect this
in the pointer type.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Internet Assigned Numbers Authority (IANA) has recently assigned
a protocol number value of 143 for Ethernet [1].
Before this assignment, encapsulation mechanisms such as Segment Routing
used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated
payload is an Ethernet frame.
In this patch, we add the definition of the Ethernet protocol number to the
kernel headers and update the SRv6 L2 tunnels to use it.
[1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Acked-by: Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, DSA drivers should configure CPU and DSA ports to their
maximum speed. In many configurations this is sufficient to make the
link work.
In some cases it is necessary to configure the link to run slower,
e.g. because of limitations of the SoC it is connected to. Or back to
back PHYs are used and the PHY needs to be driven in order to
establish link. In this case, phylink is used.
Only instantiate phylink if it is required. If there is no PHY, or no
fixed link properties, phylink can upset a link which works in the
default configuration.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one error case, tpacket_rcv drops packets after incrementing the
ring producer index.
If this happens, it does not update tp_status to TP_STATUS_USER and
thus the reader is stalled for an iteration of the ring, causing out
of order arrival.
The only such error path is when virtio_net_hdr_from_skb fails due
to encountering an unknown GSO type.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an off-by-one error in strncpy size argument in
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in:
strncmp(opt, "eee_timer:", 6)
the passed string literal: "eee_timer:" has 10 bytes (without the NULL
byte) and the passed size argument is 6. As a result, the logic will
also accept other, malformed strings, e.g. "eee_tiXXX:".
This bug doesn't seem to have any security impact since its present in
module's cmdline parsing code.
Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
caifdevs->list is traversed using list_for_each_entry_rcu()
outside an RCU read-side critical section but under the
protection of rtnl_mutex. Hence, add the corresponding lockdep
expression to silence the following false-positive warning:
[ 10.868467] =============================
[ 10.869082] WARNING: suspicious RCU usage
[ 10.869817] 5.6.0-rc1-00177-g06ec0a154aae4 #1 Not tainted
[ 10.870804] -----------------------------
[ 10.871557] net/caif/caif_dev.c:115 RCU-list traversed in non-reader section!!
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_set_coalesce() validates the previously set params
and if they are within range proceeds to apply the new ones.
The new ones, however, are not validated. This seems backwards,
probably a copy-paste error?
Compile tested only.
Fixes: d851b47b22 ("net: fec: add interrupt coalescence feature support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2860:9: warning:
converting the result of '?:' with integer constants to a boolean always
evaluates to 'true' [-Wtautological-constant-compare]
return DPAA_FD_DATA_ALIGNMENT ? ALIGN(headroom,
^
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:131:34: note: expanded
from macro 'DPAA_FD_DATA_ALIGNMENT'
\#define DPAA_FD_DATA_ALIGNMENT (fman_has_errata_a050385() ? 64 : 16)
^
1 warning generated.
This was exposed by commit 3c68b8fffb ("dpaa_eth: FMan erratum A050385
workaround") even though it appears to have been an issue since the
introductory commit 9ad1a37493 ("dpaa_eth: add support for DPAA
Ethernet") since DPAA_FD_DATA_ALIGNMENT has never been able to be zero.
Just replace the whole boolean expression with the true branch, as it is
always been true.
Link: https://github.com/ClangBuiltLinux/linux/issues/928
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
A couple of fixes:
* three netlink validation fixes
* a mesh path selection fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2020-03-10
This fixes three minor issues:
1) a setup parameter gets cleared unnecessarily when the HW config
changes,
2) insufficient error handling when initially filling the RX ring, and
3) a rarely used worker that needs to be cancelled during tear down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth's napi poll code fails to refill an entirely empty RX ring, it
kicks off buffer_reclaim_work to try again later.
Make sure that this worker is cancelled when setting the qeth device
offline. Otherwise a RX refill action can unexpectedly end up running
concurrently to bigger re-configurations (eg. resizing the buffer pool),
without any locking.
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_init_qdio_queues() fills the RX ring with an initial set of
RX buffers. If qeth_init_input_buffer() fails to back one of the RX
buffers with memory, we need to bail out and report the error.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an OSA device in prio-queue setup is reduced to 1 TX queue due to
HW restrictions, we reset its the default_out_queue to 0.
In the old code this was needed so that qeth_get_priority_queue() gets
the queue selection right. But with proper multiqueue support we already
reduced dev->real_num_tx_queues to 1, and so the stack puts all traffic
on txq 0 without even calling .ndo_select_queue.
Thus we can preserve the user's configuration, and apply it if the OSA
device later re-gains support for multiple TX queues.
Fixes: 73dc2daf11 ("s390/qeth: add TX multiqueue support for OSA devices")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh says:
====================
MACSec bugfixes related to MAC address change
We found out that there's an issue in MACSec code when the MAC address
is changed.
Both s/w and offloaded implementations don't update SCI when the MAC
address changes at the moment, but they should do so, because SCI contains
MAC in its first 6 octets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn
Eric Dumazet
David S. Miller
Julian Wiedmann
Paolo Lungaroni
Willem de Bruijn
Dominik Czarnota
Amol Grover
Jakub Kicinski
Nathan Chancellor
Nicolas Cavallari
Dmitry Bogdanov