The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 1.8V GPIO pins.
As the register names for both controllers are the same and the 36 1.8V
GPIOs and the first 36 of the 3.3V GPIOs are all bidirectional, we can
use the same configuration struct and use the ngpio property to
differentiate between the two sets of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906063737.15428-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the ngpio property from the device tree if it exists. If it doesn't
then fallback to the hardcoded value in the config.
This is in preparation for adding ast2600 support. The ast2600 SoC has
two GPIO controllers and so requires two instances of the GPIO driver.
We use the ngpio property to different between them as they have
different numbers of GPIOs.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062727.13521-1-rashmica.g@gmail.com
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.3V GPIO pins.
Additionally, it has a GPIO controller for 36 1.8V GPIO pins. We use
the ngpio property to differentiate between these controllers.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Link: https://lore.kernel.org/r/20190906062547.13264-1-rashmica.g@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After changing the valid_mask for the struct gpio_chip
to detect the need and presence of a valid mask with the
presence of a .init_valid_mask() callback to fill it in,
we augment the gpio_irq_chip to use the same logic.
Switch all driver using the gpio_irq_chio valid_mask
over to this new method.
This makes sure the valid_mask for the gpio_irq_chip gets
filled in when we add the gpio_chip, which makes it a
little easier to switch over drivers using the old
way of setting up gpio_irq_chip over to the new method
of passing the gpio_irq_chip along with the gpio_chip.
(See drivers/gpio/TODO for details.)
Cc: Joel Stanley <joel@jms.id.au>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
intel-gpio for v5.4-1
The clean up of IRQ chip initialization has been done in few drivers.
Stale record in MAINTAINERS database is removed.
The following is an automated git shortlog grouped by driver:
intel-mid:
- Pass irqchip when adding gpiochip
- MAINTAINERS: Remove stale record for gpio-intel-mid.c
lynxpoint:
- Pass irqchip when adding gpiochip
merrifield:
- Pass irqchip when adding gpiochip
pch:
- Use dev_get_drvdata
The previous merge of v5.3-rc7 was struggle enough, now it
gave rise to new errors and now I fix those too.
Fixes: 151a41014b ("Merge tag 'v5.3-rc7' into devel")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The merge of two different patch sets cleaning around in the
main driver include file collided making the function
declarations for gpiochip_[un]lock_as_irq() be defined twice
when gpiolib was unselected. Fix it up.
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: updates for v5.4
- use a helper variable for &pdev->dev in gpio-em
- tweak the ifdefs in GPIO headers
- fix function links in HTML docs
- remove an unneeded error message from ixp4xx
- use the optional clk_get in gpio-mxc instead of checking the return value
- a couple improvements in pca953x
- allow to build gpio-lpc32xx on non-lpc32xx targets
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for reported issues for
5.3-rc7
Also included in here is the documentation for how we are handling
hardware issues under embargo that everyone has finally agreed on, as
well as a MAINTAINERS update for the suckers who agreed to handle the
LICENSES/ files.
All of these have been in linux-next last week with no reported
issues"
* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fsi: scom: Don't abort operations for minor errors
vmw_balloon: Fix offline page marking with compaction
VMCI: Release resource if the work is already queued
Documentation/process: Embargoed hardware security issues
lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
mei: me: add Tiger Lake point LP device ID
intel_th: pci: Add Tiger Lake support
intel_th: pci: Add support for another Lewisburg PCH
stm class: Fix a double free of stm_source_device
MAINTAINERS: add entry for LICENSES and SPDX stuff
fpga: altera-ps-spi: Fix getting of optional confd gpio
Pull USB fixes from Greg KH:
"Here are some small USB fixes that have been in linux-next this past
week for 5.3-rc7
They fix the usual xhci, syzbot reports, and other small issues that
have come up last week.
All have been in linux-next with no reported issues"
* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-wdm: fix race between write and disconnect due to flag abuse
usb: host: xhci: rcar: Fix typo in compatible string matching
usb: host: xhci-tegra: Set DMA mask correctly
USB: storage: ums-realtek: Whitelist auto-delink support
USB: storage: ums-realtek: Update module parameter description for auto_delink_en
usb: host: ohci: fix a race condition between shutdown and irq
usb: hcd: use managed device resources
typec: tcpm: fix a typo in the comparison of pdo_max_voltage
usb-storage: Add new JMS567 revision to unusual_devs
usb: chipidea: udc: don't do hardware access if gadget has stopped
usbtmc: more sanity checking for packet size
usb: udc: lpc32xx: silence fall-through warning
Pull networking fixes from David Miller:
1) Fix some length checks during OGM processing in batman-adv, from
Sven Eckelmann.
2) Fix regression that caused netfilter conntrack sysctls to not be
per-netns any more. From Florian Westphal.
3) Use after free in netpoll, from Feng Sun.
4) Guard destruction of pfifo_fast per-cpu qdisc stats with
qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
in pfifo_fast_enqueue().
5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.
6) Handle neigh events on internal ports correctly in nfp, from John
Hurley.
7) Clear SKB timestamp in NF flow table code so that it does not
confuse fq scheduler. From Florian Westphal.
8) taprio destroy can crash if it is invoked in a failure path of
taprio_init(), because the list head isn't setup properly yet and
the list del is unconditional. Perform the list add earlier to
address this. From Vladimir Oltean.
9) Make sure to reapply vlan filters on device up, in aquantia driver.
From Dmitry Bogdanov.
10) sgiseeq driver releases DMA memory using free_page() instead of
dma_free_attrs(). From Christophe JAILLET.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
net: seeq: Fix the function used to release some memory in an error handling path
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
net: bcmgenet: use ethtool_op_get_ts_info()
tc-testing: don't hardcode 'ip' in nsPlugin.py
net: dsa: microchip: add KSZ8563 compatibility string
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
net: aquantia: fix out of memory condition on rx side
net: aquantia: linkstate irq should be oneshot
net: aquantia: reapply vlan filters on up
net: aquantia: fix limit of vlan filters
net: aquantia: fix removal of vlan 0
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
taprio: Fix kernel panic in taprio_destroy
net: dsa: microchip: fill regmap_config name
rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
amd-xgbe: Fix error path in xgbe_mod_init()
netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
mac80211: Correctly set noencrypt for PAE frames
...
In commit 99cd149efe ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe ("sgiseeq: replace use of dma_cache_wback_inv")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the bogus detection of 32bit user mode for uretprobes which
caused corruption of the user return address resulting in
application crashes. In the uprobes handler in_ia32_syscall() is
obviously always returning false on a 64bit kernel. Use
user_64bit_mode() instead which works correctly.
- Prevent large page splitting when ftrace flips RW/RO on the kernel
text which caused iTLB performance issues. Ftrace wants to be
converted to text_poke() which avoids the problem, but for now
allow large page preservation in the static protections check when
the change request spawns a full large page.
- Prevent arch_dynirq_lower_bound() from returning 0 when the IOAPIC
is configured via device tree. In the device tree case the GSI 1:1
mapping is meaningless therefore the lower bound which protects the
GSI range on ACPI machines is irrelevant. Return the lower bound
which the core hands to the function instead of blindly returning 0
which causes the core to allocate the invalid virtual interupt
number 0 which in turn prevents all drivers from allocating and
requesting an interrupt.
- Remove the bogus initialization of LDR and DFR in the 32bit bigsmp
APIC driver. That uses physical destination mode where LDR/DFR are
ignored, but the initialization and the missing clear of LDR caused
the APIC to be left in a inconsistent state on kexec/reboot.
- Clear LDR when clearing the APIC registers so the APIC is in a well
defined state.
- Initialize variables proper in the find_trampoline_placement()
code.
- Silence GCC( build warning for the real mode part of the build"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/cpa: Prevent large page split when ftrace flips RW on kernel text
x86/build: Add -Wnoaddress-of-packed-member to REALMODE_CFLAGS, to silence GCC9 build warning
x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
x86/apic: Include the LDR when clearing out APIC registers
x86/apic: Do not initialize LDR and DFR for bigsmp
uprobes/x86: Fix detection of 32-bit user mode
x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines
Pull perf fixes from Thomas Gleixner:
"Two fixes for perf x86 hardware implementations:
- Restrict the period on Nehalem machines to prevent perf from
hogging the CPU
- Prevent the AMD IBS driver from overwriting the hardwre controlled
and pre-seeded reserved bits (0-6) in the count register which
caused a sample bias for dispatched micro-ops"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd/ibs: Fix sample bias for dispatched micro-ops
perf/x86/intel: Restrict period on Nehalem
Pull turbostat updates from Len Brown:
"User-space turbostat (and x86_energy_perf_policy) patches.
They are primarily bug fixes from users"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: update version number
tools/power turbostat: Add support for Hygon Fam 18h (Dhyana) RAPL
tools/power turbostat: Fix caller parameter of get_tdp_amd()
tools/power turbostat: Fix CPU%C1 display value
tools/power turbostat: do not enforce 1ms
tools/power turbostat: read from pipes too
tools/power turbostat: Add Ice Lake NNPI support
tools/power turbostat: rename has_hsw_msrs()
tools/power turbostat: Fix Haswell Core systems
tools/power turbostat: add Jacobsville support
tools/power turbostat: fix buffer overrun
tools/power turbostat: fix file descriptor leaks
tools/power turbostat: fix leak of file descriptor on error return path
tools/power turbostat: Make interval calculation per thread to reduce jitter
tools/power turbostat: remove duplicate pc10 column
tools/power x86_energy_perf_policy: Fix argument parsing
tools/power: Fix typo in man page
tools/power/x86: Enable compiler optimisations and Fortify by default
tools/power x86_energy_perf_policy: Fix "uninitialized variable" warnings at -O2
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes: 19971f5ea0 ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>