The CONFIG_TEGRA_VDE has been deprecated and replaced with the new V4L
options after de-staging of the tegra-vde driver. Update the config entry.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TODO of tegra-vde driver has been completed, driver now supports
V4L2 stateless video decoding API. Relocate driver to drivers/media.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
BSEV DMA timeouts if VDE is downclocked by x10. Bump the timeout to allow
DMA to complete. We don't support freq scaling yet, this is just a minor
improvement which may become useful sometime later.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The legacy UAPI became unnecessary with the V4L stateless decoder API
support addition to the Tegra decoder driver. Remove legacy UAPI support.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Expose Tegra video decoder as a generic V4L M2M stateless video decoder.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Factor out H.264 hardware programming code into separate source file in a
preparation to support V4L API by the Tegra video decoder driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add new V4L2_H264_DECODE_PARAM_FLAG_P/BFRAME flags that are needed by
NVIDIA Tegra video decoder. Userspace will have to set these flags in
accordance to the type of a decoded frame.
Reviewed-by: Nicolas Dufresne <nicolas@collabora.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
All device drivers got runtime PM and OPP support. Flip the core domain
support status for Tegra20 and Tegra30 SoCs.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Replace dev_printk() with a generic dev_err_probe() helper which silences
noisy error messages about deferred probe and makes easy to debug failing
deferred probe by printing notification about the failure to KMSG in the
end of kernel booting process and by adding failing device and the reason
of deferred probe to devices_deferred of debugfs. This was proven to be
useful in the case of eDP driver regression by immediately showing why
display driver was failing when user asked for help, otherwise it would've
been much more difficult to debug such problems on a third party device
that doesn't have developer setup.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add MMC aliases to ensure that the /dev/mmcblk IDs won't change depending
on the probe order of the MMC drivers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename DSI bridge node to match the requirement of the DSI DT schema.
This silences DTB-check warning about the incorrect name.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable S/PDIF controller to enable HDMI audio support on ASUS TF101.
Use nvidia,fixed-parent-rate property that prevents audio rate conflict
between S/PDIF and I2S.
Tested-by: Robert Eckelmann <longnoserob@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186+ hangs if host1x hardware is disabled at a kernel boot time
because we touch hardware before runtime PM is resumed. Move sync point
assignment initialization to the RPM-resume callback. Older SoCs were
unaffected because they skip that sync point initialization.
Tested-by: Jon Hunter <jonathanh@nvidia.com> # T186
Reported-by: Jon Hunter <jonathanh@nvidia.com> # T186
Fixes: 6b6776e2ab ("gpu: host1x: Add initial runtime PM and OPP support")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove non-existent properties from the example of the binding. These
properties were borrower from the old txt binding, but they were never
used in practice and aren't documented in the new binding. They aren't
reported by the binding checker because dtschema needs extra patch that
hasn't been upstreamed yet to make unevaluatedProperties work properly.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211216160229.17049-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Memory Client should be blocked before hardware reset is asserted in order
to prevent memory corruption and hanging of memory controller.
Document Memory Client resets of Host1x, GR2D and GR3D hardware units.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Document new DVFS OPP table and power domain properties of the Host1x bus
and devices sitting on the bus.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Document sub-nodes which describe Tegra SoC clocks that require a higher
voltage of the core power domain in order to operate properly on a higher
clock rates. Each node contains a phandle to OPP table and power domain.
The root PLLs and system clocks don't have any specific device dedicated
to them, clock controller is in charge of managing power for them.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Support new nvidia,fixed-parent-rate device-tree property which instructs
I2S that board wants parent clock rate to stay at a fixed rate. This allows
to play audio over S/PDIF and I2S simultaneously. The root of the problem
is that audio components on Tegra share the same audio PLL, and thus, only
a subset of rates can be supported if we want to play audio simultaneously.
Filter out audio rates that don't match parent clock rate if device-tree
has the nvidia,fixed-parent-rate property.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-14-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPDIF and other SoC components share audio PLL on Tegra, thus only one
component may set the desired base clock rate. This creates problem for
HDMI audio because it uses SPDIF and audio may not work if SPDIF's clock
doesn't exactly match standard audio rate since some receivers may reject
audio in that case. Filter out audio rates which SPDIF output can't
support, assuming that other components won't change rate at runtime.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-13-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Clean up whitespaces, defines and variables.
- Remove obsolete code.
- Adhere to upstream coding style.
- Don't override returned error code.
- Replace pr_err with dev_err.
No functional changes are made by this patch. This is a minor code's
refactoring that will ease further maintenance of the driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211204143725.31646-9-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Document new nvidia,fixed-parent-rate property which instructs that this
board wants parent clock to stay at a fixed rate. It allows to prevent
conflicts between audio components that share same parent PLL. For
instance, this property allows to have HDMI audio, speaker and headphones
in the system playing audio simultaneously, which is a common pattern for
consumer devices.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211204143725.31646-4-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable S/PDIF controller to enable HDMI audio support on Toshiba AC100.
Use nvidia,fixed-parent-rate property that prevents audio rate conflict
between S/PDIF and I2S.
Tested-by: Agneli <poczt@protonmail.ch>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable S/PDIF controller to enable HDMI audio support on Acer A500.
Use nvidia,fixed-parent-rate property that prevents audio rate conflict
between S/PDIF and I2S.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
MPE, VI, EPP and ISP were never used and we don't have drivers for them.
Since these modules are enabled by default in a device-tree, a device is
created for them, blocking voltage scaling because there is no driver to
bind, and thus, state of PMC driver is never synced. Disable them.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Memory access must be blocked before hardware reset is asserted and before
power is gated, otherwise a serious hardware fault is inevitable. Add
reset for memory clients to the GR2D, GR3D and Host1x nodes.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Memory access must be blocked before hardware reset is asserted and before
power is gated, otherwise a serious hardware fault is inevitable. Add
reset for memory clients to the GR2D, GR3D and Host1x nodes.
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add OPP tables and power domains to all peripheral devices which
support power management on Tegra30 SoC.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All Tegra20/30/114 serial and audio drivers depend on the Tegra20 APB DMA
driver, enable this DMA driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable Tegra20 S/PDIF driver that is a part of HDMI audio subsystem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
DMA buffers of 2D/3D engines aren't mapped properly when
CONFIG_ARM_DMA_USE_IOMMU=y. The memory management code of Tegra DRM driver
has a longstanding overhaul overdue and it's not obvious where the problem
is in this case. Hence let's add back the old workaround which we already
had sometime before. It explicitly detaches DRM devices from the offending
implicit IOMMU domain. This fixes a completely broken 2d/3d drivers in
case of ARM32 multiplatform kernel config.
Cc: stable@vger.kernel.org
Fixes: fa6661b7aa ("drm/tegra: Optionally attach clients to the IOMMU")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Host1x DMA buffer isn't mapped properly when CONFIG_ARM_DMA_USE_IOMMU=y.
The memory management code of Host1x driver has a longstanding overhaul
overdue and it's not obvious where the problem is in this case. Hence
let's add back the old workaround which we already had sometime before.
It explicitly detaches Host1x device from the offending implicit IOMMU
domain. This fixes a completely broken Host1x DMA in case of ARM32
multiplatform kernel config.
Cc: stable@vger.kernel.org
Fixes: af1cbfb9bf ("gpu: host1x: Support DMA mapping of buffers")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add OPP tables and power domains to all peripheral devices which
support power management on Tegra20 SoC.
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Extend memory OPPs with 500 MHz entry. This clock rate is used by ASUS
Transformer tablets.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move runtime PM management of older UAPI code paths into the common place.
This removes boilerplate code from client drivers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Runtime PM is now universally available, make it mandatory by removing
the pm_runtime_enabled() checks.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CDMA must be stopped before hardware is suspended. Add channel stopping
to RPM suspend callback. Add system level suspend-resume callbacks.
Runtime PM initialization is moved to host1x client init phase because
RPM callback now uses host1x channel that is available only when host1x
client is registered.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CDMA must be stopped before hardware is suspended. Add channel stopping
to RPM suspend callback. Add system level suspend-resume callbacks.
Runtime PM initialization is moved to host1x client init phase because
RPM callback now uses host1x channel that is available only when host1x
client is registered.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HDMI on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now HDMI driver must use
OPP API for driving the controller's clock rate because OPP API takes
care of reconfiguring the domain's performance state based on HDMI clock
rate. Add OPP support to the HDMI driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add OPP and SoC core voltage scaling support to the display controller
driver. This is required for enabling system-wide DVFS on pre-Tegra186
SoCs.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add host1x_channel_stop() which waits till channel becomes idle and then
stops the channel hardware. This is needed for supporting suspend/resume
by host1x drivers since the hardware state is lost after power-gating,
thus the channel needs to be stopped before client enters into suspend.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add runtime PM and OPP support to the Host1x driver. For the starter we
will keep host1x always-on because dynamic power management require a major
refactoring of the driver code since lot's of code paths are missing the
RPM handling and we're going to remove some of these paths in the future.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra20 SoC supports only S/PDIF source for HDMI audio. Register ASoC HDMI
S/PDIF CODEC for Tegra20, it will be linked with the S/PDIF CPU DAI.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Asus Transformer TF700T is a Tegra30 tablet device which uses RGB->DSI
bridge that requires a precise clock rate in order to operate properly.
Tegra30 has a dedicated PLL for each display controller, hence the PLL
rate can be changed freely. Allow PLL rate changes on Tegra30+ for RGB
output. Configure the clock rate before display controller is enabled
since DC itself may be running off this PLL and it's not okay to change
the rate of the active PLL that doesn't support dynamic frequency
switching since hardware will hang.
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> #TF700T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Asus TF700T tablet uses TC358768 DPI->DSI bridge that sits between Tegra's
DPI output and display panel input. Bridge requires to have stable PCLK
output before RGB encoder is enabled because it uses PCLK by itself to
clock internal logic and bridge is programmed before Tegra's encoder is
enabled. Hence the PCLK clock shifter must be programmed when CRTC is
enabled, otherwise clock is unstable and bridge hangs because of it.
Move the shifter programming from RGB encoder into CRTC.
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> #TF700T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SPI on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now SPI driver must use OPP
API for driving the controller's clock rate because OPP API takes care
of reconfiguring the domain's performance state in accordance to the
rate. Add OPP support to the driver.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NAND on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now NAND must be resumed using
runtime PM API in order to initialize the NAND power state. Add runtime PM
and OPP support to the NAND driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SDHCI on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now SDHCI must be resumed using
runtime PM API in order to initialize the SDHCI power state. The SDHCI
clock rate must be changed using OPP API that will reconfigure the power
domain performance state in accordance to the rate. Add runtime PM and OPP
support to the SDHCI driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PWM on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now PWM must be resumed using
runtime PM API in order to initialize the PWM power state. The PWM clock
rate must be changed using OPP API that will reconfigure the power domain
performance state in accordance to the rate. Add runtime PM and OPP
support to the PWM driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The GMI bus on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now GMI must be resumed using
runtime PM API in order to initialize the GMI power state. Add runtime PM
and OPP support to the GMI driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra USB controller belongs to the core power domain and we're going
to enable GENPD support for the core domain. Now USB controller must be
resumed using runtime PM API in order to initialize the USB power state.
We already support runtime PM for the CI device, but CI's PM is separated
from the RPM managed by tegra-usb driver. Add runtime PM and OPP support
to the driver.
Acked-by: Peter Chen <peter.chen@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CORE power domain uses name of device-tree node, which is inconsistent with
the names of PMC domains. Set the name to "core" to make it consistent.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Only couple drivers need to get the -ENODEV error code and majority of
drivers need to explicitly initialize the performance state. Add new
common helper which sets up OPP table for these drivers.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Device-tree schema doesn't allow domain name to start with a number.
We don't use 3d domain yet in device-trees, so rename it to the name
used by Tegra TRMs: TD, TD2.
Reported-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
GENPD core now can set up domain's performance state properly while device
is RPM-suspended. Runtime PM of a device must be enabled during setup
because GENPD checks whether device is suspended and check doesn't work
while RPM is disabled. Instead of replicating the boilerplate RPM-enable
code around OPP helper for each driver, let's make OPP helper to take care
of enabling it.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use resource-managed helpers to make code cleaner and more correct,
properly releasing all resources in case of driver probe error.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The FUSE controller is enabled at a boot time. Reset it in order to put
hardware and clock into clean and disabled state.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously we assumed that devm_tegra_core_dev_init_opp_table() will
be used only by drivers that will always have device with OPP table,
but this is not true anymore. For example now Tegra30 will have OPP table
for PWM, but Tegra20 not and both use the same driver. Hence let's not
print the error message about missing OPP table in the common helper,
we can print it elsewhere.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Clock-and-Reset controller resides in a core power domain on NVIDIA
Tegra SoCs. In order to support voltage scaling of the core power domain,
we hook up DVFS-capable clocks to the core GENPD for managing of the
GENPD's performance state based on the clock changes.
Some clocks don't have any specific physical hardware unit that backs
them, like root PLLs and system clock and they have theirs own voltage
requirements. This patch adds new clk-device driver that backs the clocks
and provides runtime PM functionality for them. A virtual clk-device is
created for each such DVFS-capable clock at the clock's registration time
by the new tegra_clk_register() helper. Driver changes clock's device
GENPD performance state based on clk-rate notifications.
In result we have this sequence of events:
1. Clock driver creates virtual device for selective clocks, enables
runtime PM for the created device and registers the clock.
2. Clk-device driver starts to listen to clock rate changes.
3. Something changes clk rate or enables/disables clk.
4. CCF core propagates the change through the clk tree.
5. Clk-device driver gets clock rate-change notification or GENPD core
handles prepare/unprepare of the clock.
6. Clk-device driver changes GENPD performance state on clock rate
change.
7. GENPD driver changes voltage regulator state change.
8. The regulator state is committed to hardware via I2C.
We rely on fact that DVFS is not needed for Tegra I2C and that Tegra I2C
driver already keeps clock always-prepared. Hence I2C subsystem stays
independent from the clk power management and there are no deadlock spots
in the sequence.
Currently all clocks are registered very early during kernel boot when the
device driver core isn't available yet. The clk-device can't be created
at that time. This patch splits the registration of the clocks in two
phases:
1. Register all essential clocks which don't use RPM and are needed
during early boot.
2. Register at a later boot time the rest of clocks.
This patch adds power management support for Tegra20 and Tegra30 clocks.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CPU of Nyan Chromebooks is overheating badly because apparently hardware
soctherm controller doesn't work well. Add CPU thermal zones to enable
software thermal control over CPU and fix the overheat trouble.
Tested-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable CPU DFLL node on Nyan Chromebooks. DFLL was previously disabled due
to Linux kernel CPUFreq driver which didn't support suspend-resume. That
problem was fixed years ago, but DFLL was never re-enabled.
Tested-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add dedicated device-tree for 1080p version of Nyan Big in order to
describe display panel properly. FHD panel doesn't support modes other
than 1080p, hence it's wrong to use incompatible lower resolution panel
in device-tree.
Tested-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable charger, touchpad and EC drivers found on Acer Tegra124 (Nyan)
Chromebooks, display bridge found on ASUS TF700T and audio codecs
found on ASUS tablets.
Suggested-by: Thomas Graichen <thomas.graichen@gmail.com> # Nyan options
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The current default is to leave the VDE clock's parent at the default,
which is clk_m. However, that is not a configuration that will allow the
VDE to function. Reparent it to pll_p instead to make sure the hardware
can actually decode video content.
Tested-by: Anton Bambura <jenneron@protonmail.com> # ASUS TF701T
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
OPP table name now should start with "opp-table" and OPP entries
shouldn't contain commas and @ signs in accordance to the new schema
requirement. Reorganize CPU and EMC OPP table device-tree nodes.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Regulators defined at the top level in device tree are no longer part of
a simple bus and therefore don't have a reg property. Nodes without a
reg property shouldn't have a unit-address either, so drop the unit
address from the node names. To ensure nodes aren't duplicated (in which
case they would end up merged in the final DTB), append the name of the
regulator to the node name.
[treding@nvidia.com: factored out patch and wrote commit message]
Signed-off-by: David Heidelberg <david@ixit.cz>
Co-developed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Vendor prefix shouldn't start with capital letter. The Elpida Memory
compatible was never used in practice, hence just correct the compatible.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register misc device in the end of driver's probing since device should
become visible to userspace once driver is fully prepared. Do the opposite
in case of driver removal. This is a minor improvement that doesn't solve
any problem, but makes code more consistent.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Not all OPP entries fit into a single word. In particular NVIDIA Tegra OPP
tables use multi-word names. Allow OPP entry to have multi-worded name
separated by hyphen. This silences DT checker warnings about wrong naming
scheme.
Reviewed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tegra I2C device isn't guaranteed to be suspended after removal of
the driver since driver uses pm_runtime_put() that is asynchronous and
pm_runtime_disable() cancels pending power-change requests. This means
that potentially refcount of the clocks may become unbalanced after
removal of the driver. This a very minor problem which unlikely to
happen in practice and won't cause any visible problems, nevertheless
let's replace pm_runtime_disable() with pm_runtime_force_suspend() and
use pm_runtime_put_sync() which disables RPM of the device and puts it
into suspend before driver is removed.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
pm_runtime_disable() cancels all pending power requests, while they
should be completed for the Tegra SPI driver. Otherwise SPI clock won't
be disabled ever again because clk refcount will become unbalanced.
Enforce runtime PM suspension to put device into expected state before
driver is unbound and device's RPM state is reset by driver's core.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211023225951.14253-2-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_disable() cancels all pending power requests, while they
should be completed for the Tegra SPI driver. Otherwise SPI clock won't
be disabled ever again because clk refcount will become unbalanced.
Enforce runtime PM suspension to put device into expected state before
driver is unbound and device's RPM state is reset by driver's core.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211023225951.14253-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Osipenko