START_SEC was changed in e0905e85a7.
Also, update the error message to mention how to format the partition at
the REPL, and make the total message shorter to save a bit of flash.
Signed-off-by: Damien George <damien@micropython.org>
For certain operands to mpn_div, the existing code path for
`DIG_SIZE == MPZ_DBL_DIG_SIZE / 2` had a bug in it where borrow could still
overflow in the `(x >= *n || *n - x <= borrow)` branch, ie
`borrow + x - (mpz_dbl_dig_t)*n` overflows the borrow variable. In such
cases the subsequent right-shift of borrow would not bring in the overflow
bit, leading to an error in the result. An example division that had
overflow when MPZ_DIG_SIZE = 16 is `(2 ** 48 - 1) ** 2 // (2 ** 48 - 1)`.
This is fixed in this commit by simplifying the code and handling the low
digits of borrow first, and then the upper bits (to shift down) separately.
There is no longer a distinction between `DIG_SIZE < MPZ_DBL_DIG_SIZE / 2`
and `DIG_SIZE == MPZ_DBL_DIG_SIZE / 2`.
This commit also simplifies the second part of the calculation so that
borrow does not need to be negated (instead the code just works knowing
that borrow is negative and using + instead of - in calculations involving
borrow).
Fixes#6777.
Signed-off-by: Damien George <damien@micropython.org>
In particular the firmware can now be built in a build directory that lives
outside the source tree, and the py/modarray.c file will still be found.
See issue #6837.
Signed-off-by: Damien George <damien@micropython.org>
The "word" referred to by BYTES_PER_WORD is actually the size of mp_obj_t
which is not always the same as the size of a pointer on the target
architecture. So rename this config value to better reflect what it
measures, and also prefix it with MP_.
For uses of BYTES_PER_WORD in setting the stack limit this has been
changed to sizeof(void *), because the stack usually grows with
machine-word sized values (eg an nlr_buf_t has many machine words in it).
Signed-off-by: Damien George <damien@micropython.org>
It's only used in one location, to test if << or >> will overflow when
shifting mp_uint_t. For such a test it's clearer to use sizeof(lhs_val),
which will be valid even if the type of lhs_val changes.
Signed-off-by: Damien George <damien@micropython.org>
To simplify config, there's no need to specify MP_PLAT_PRINT_STRN if it's
the same as the default definition in py/mpconfig.h.
Signed-off-by: Damien George <damien@micropython.org>
Otherwise it resets the ADC peripheral each time a new ADC object is
constructed, which can reset other state that has already been set up.
See issue #6833.
Signed-off-by: Damien George <damien@micropython.org>
Default to just calling python since that is most commonly available: the
official installer or zipfiles from python.org, anaconda, nupkg all result
in python being available but not python3. In other words: the default
used so far is wrong. Note that os.name is 'posix' when running the python
version which comes with Cygwin or MSys2 so they are not affected by this.
However of all possible ways to get Python on Windows, only Cygwin provides
no python command so update the default way for running tests in the
README.
With mboot encrpytion and fsload enabled, the DEBUG build -O0 compiler
settings result in mboot no longer fitting in the 32k sector. This commit
changes this to -Og which also brings it into line with the regular stm32
build.
MCUs with device-only USB peripherals (eg L0, WB) do not implement (at
least not in the ST HAL) the HAL_PCD_DisconnectCallback event. So if a USB
cable is disconnected the USB driver does not deinitialise itself
(usbd_cdc_deinit is not called) and the CDC driver can stay in the
USBD_CDC_CONNECT_STATE_CONNECTED state. Then if the USB was attached to
the REPL, output can become very slow waiting in usbd_cdc_tx_always for
500ms for each character.
The disconnect event is not implemented on these MCUs but the suspend event
is. And in the situation where the USB cable is disconnected the suspend
event is raised because SOF packets are no longer received.
The issue of very slow output on these MCUs is fixed in this commit (really
worked around) by adding a check in usbd_cdc_tx_always to see if the USB
device state is suspended, and, if so, breaking out of the 500ms wait loop.
This should also help all MCUs for a real USB suspend.
A proper fix for MCUs with device-only USB would be to implement or somehow
synthesise the HAL_PCD_DisconnectCallback event.
See issue #6672.
Signed-off-by: Damien George <damien@micropython.org>
PIO state machines can make a conditional jump on the state of a pin: the
`JMP PIN` command. This requires the pin to be configured with
`sm_config_set_jmp_pin`, but until now we didn't have a way of doing that
in MicroPython.
This commit adds a new `jmp_pin=None` argument to `StateMachine`. If it is
not `None` then we try to interpret it as a Pin, and pass its value to
`sm_config_set_jmp_pin`.
Signed-off-by: Tim Radvan <tim@tjvr.org>
Damien George
Xiang Xiao
stijn
Andrew Leech
Tim Radvan