The hidapi cmsis-dap backend is using a packet_size of
64+1: 64 is the bMaxPacketSize0 and 1 is the hid Report-Id.
In hidapi::hid_write(), the packet_size is decremented by 1 and
stored for the next transfer.
The packet_size is now valid bMaxPacketSize0=64,
so when hid_read() is called, libusb_bulk_transfer() finishes w/o timeout.
For the libusb bulk backend, the same packet_size of 64+1 is used,
but there's no hid_write() to decrement and store it for the next read.
So the next time a read is done, it will try to read 64+1 bytes.
Fix this by putting the packet logic within each backend.
Use calloc() to allocate the struct cmsis_dap to be on safer side.
Change-Id: I0c450adbc7674d5fcd8208dd23062d5cdd209efd
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5920
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Now that the old drivers have been converted to libusb1, there is
no need to keep the build dependency from libusb0.
Drop libusb0 from configure and makefiles, remove the libusb0
helper and remove libusb0 and libusb-compat from the README files.
Change-Id: Icc05be74ae5971ba6cbb67d39107c709a4d826e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5993
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: Idef0b6cf10fab583bc8d13b3b4fadd5cc368c090
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5990
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: I3f334f2d02515d612097955e714910a587169990
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5992
Tested-by: jenkins
All Altera USB Blaster devices require a dedicated line in the
udev rules, but some USB VID/PID present in interface and board
config file is missing in udev rules.
Add the missing Altera USB Blaster devices in udev rules.
While there, fix an incorrect pair VID/PID that are reported
swapped inside a comment.
Change-Id: I2d67e90b10db99ef2638405585859c1393456f65
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6102
Tested-by: jenkins
All ftdi devices require a dedicated line in the udev rules, but
some USB VID/PID present in interface and board config file is
missing in udev rules.
Add the missing ftdi devices in udev rules.
Change-Id: I850a4a95a2d4bb63b3fd09be803be8c23c4d6b49
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6101
Tested-by: jenkins
The API Jim_CreateCommand() in latest version of jimtcl leaks the
memory allocated internally by jimtcl when it converts the string
command-name to a Jim_Obj.
The fix is already merged upstream and would be available in next
jimtcl 0.81, expected in ~6 months, hopefully before the next tag
for OpenOCD v0.12.0.
OpenOCD v0.11.0 is distributed with jimtcl 0.79.
Debian distributes jimtcl as a separate library package and today
it's still on 0.79.
It make sense to keep using jimtcl 0.80 in current development
cycle to test it further. But having this background memory leak
noise hides the eventual new memory leaks that could come from the
development activity.
This patch uses the internal jimtcl API Jim_CreateCommandObj() and
correctly free the internal object, avoiding the memory leak.
Being an internal API, it is not accessible if OpenOCD is linked
with an external jimtcl library. Nevertheless, building jimtcl as
a submodule of OpenOCD makes the trick effective.
The scope of this patch is thus limited at developers that build
OpenOCD with jimtcl submodule and need to control and debug memory
leaks.
This patch is supposed to be removed as soon as jimtcl 0.81 gets
available.
The added code is located, on purpose, in an area of the file that
hopefully will not conflict other patches pending in gerrit.
Change-Id: I4d300ad21bdb6c616c3f0f14b429b4fdf360900d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6130
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
After bootstrapping build, if we want to do an out-of-tree build (ie: in the
OOT-build dir) we have a build failure because build system relies on
the OOT-build/src directory exists
```sh
./bootstrap
mkdir OOT-build
cd OOT-build
../configure --disable-dependency-tracking --<flag1> --<flag2> ...
make
$ LANG=C make
cat ../src/helper/startup.tcl ../src/jtag/startup.tcl ../src/target/startup.tcl ../src/server/startup.tcl ../src/flash/startup.tcl | ../src/helper/bin2char.sh > src/startup_tcl.inc || { rm -f src/startup_tcl.inc; false; }
/bin/bash: line 1: src/startup_tcl.inc: No such file or directory
make: *** [Makefile:6603: src/startup_tcl.inc] Error 1
```
These kind of errors are fixed indicating relevant directory creation in
Makefile.am before actually relying on it.
Change-Id: I8185fd41ef942184597dc4c0092796034572cbe1
Signed-off-by: Raúl Sánchez Siles <rasasi78@gmail.com>
Reviewed-on: http://openocd.zylin.com/6106
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
introduction of 'enum stm32l4_rdp' enumerating possible RDP levels for
devices with and without TrustZone.
also in 'stm32l4_flash_bank' structure we added and rdp and tzen members
to store read values by the helper 'stm32l4_sync_rdp_tzen'
these new members are used to display security and protection status
while probing the flash.
Change-Id: Icf883189715278a3323fe210d295047678b16592
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5541
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
instead of adding a new member into stm32l4_part_info for every relevant
feature, .flags serves as container for the devices' features.
identified features: F_HAS_DUAL_BANK, F_USE_ALL_WRPXX, F_HAS_TZ
Change-Id: I3093e54c6509dec33043ebe6f87675198bf1967a
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
stm32l4_protect: was using one WRP area per bank, without checking
if it is already protecting some sectors.
protection algo is more complicated than that, before using a WRP area
we should check if it is already used, then either reuse it for extension
(or reduction) or use a free area.
introduce a new command: stm32l4x wrp_info bank_num ['bank1'|'bank2']
this command lists the protected areas using WRP.
Note: for some devices like STM32L4R/S in single bank mode, all 4 WRP areas
are usable for that bank, to manage this case an attribute 'use_all_wrpxx'
was introduced into stm32l4_part_info and used later in protection handlers
example usage:
$ telnet localhost 4444
> flash probe 0
device idcode = 0x10036470 (STM32L4R/L4Sxx - Rev: Y)
flash size = 2048kbytes
flash mode : dual-bank
flash 'stm32l4x' found at 0x08000000
> stm32l4x wrp_info 0
no protected areas
> flash protect 0 0 4 on
set protection for sectors 0 through 4 on flash bank 0
> flash protect 0 8 9 on
set protection for sectors 8 through 9 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][8,9]
> flash protect 0 6 6 on
the device WRPxy are not enough to set the requested protection
failed setting protection for blocks 6 to 6
> flash protect 0 3 5 on
set protection for sectors 3 through 5 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,5][8,9]
> flash protect 0 6 7 on
set protection for sectors 6 through 7 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,9]
> flash protect 0 5 6 off
cleared protection for sectors 5 through 6 on flash bank 0
> stm32l4x wrp_info 0
protected areas: [0,4][7,9]
Change-Id: I42bd84fa66edd93406e18c6d89310faa5267ffa7
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/6107
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this is a rework of #5320 started by Andreas then abandoned.
same syntax as in stm32f2x driver:
enable OTP for writing
> stm32l4x otp 1 enable
write to OTP
> flash write_bank 1 foo.bin 0
> flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1
read OTP
> mdw 0x1FFF7000 4
disable OTP
> stm32l4x otp 1 disable
Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5537
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In flash/nor/cfi.c:835 struct cfi_info is allocated by malloc(). As
write-mem was uninitialized the pointer pointed to an out of range
address, which led to a segmentation fault and crashed openocd.
This happened during flash-command of an external flash-bank, using
cfi.
Use calloc() instead.
While on it check for NULL return and remove unnecessary initialzation.
Change-Id: I0e2ffb90559afe7f090837023428dcc06b2e29f6
Signed-off-by: Mischa Studer <mischa.studer@csa.ch>
Reviewed-on: http://openocd.zylin.com/6070
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit 4c00f96fc2 ("configure.ac: switch to autoconf 2.69")
changes the required minor version of autoconf.
Update the README file accordingly.
Change-Id: I98b32b888ff531300f03c4ef9ebcbf8110509e52
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6114
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
In case of some error, the USB device and firmware file are still
claimed. Make sure refcounting is properly accounted for both cases.
Change-Id: I933114f68e59280e58372c0941a0062fe96ab340
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/6115
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For Zephyr rtos support it is necessary to define general register
numbers for architecture. There were some already in arc.h file.
Let's define ARC registers numbers as a set instead of separate defines.
Change-Id: I63742b8608f9556c2ec9bd2661a0fd9cf88e9b74
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-on: http://openocd.zylin.com/6105
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This removes some warnings which prevent a successful build with -Werror
which is enabled by default. I'm using gcc 11, so maybe others are not
getting this warnings yet.
In src/flash/nor/numicro.c the debug messages were misleadingly indented.
In src/target/arm920t.c the array size where smaller than expected from
the receiving function.
Change-Id: I66f5c6a63beb9f9416e73b726299297476c884d8
Signed-off-by: Rene Kita <git@rkta.de>
Reviewed-on: http://openocd.zylin.com/6104
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Support halting the CPU directly after a reset. If halt is
requested, the CPU stops directly at the reset vector, before
any code is executed.
This functionality was implemented using the Reset Catch
debug event.
Change-Id: If90d54c088442340376f0b588ba10267ea8e7327
Signed-off-by: Christian Hoff <christian.hoff@advantest.com>
Reviewed-on: http://openocd.zylin.com/5947
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
