Kasli is an open hardware FPGA board. It is part of the Sinara family of
devices designed to control quantum physics experiments (see Sayma_AMC
for other boards already suppported by openocd).
Kasli was developed as part of the opticlock project. It features a
Xilinx Artix 7 100T FPGA, DDR3 RAM, a clock reconstruction and
distribution network, four 6 Gb/s transceiver links (three SFP and
one SATA) as well as interfaces to up to 12 Eurocard Extension Modules
(EEMs).
https://github.com/m-labs/sinara/wiki/Kaslihttp://www.opticlock.de/en/
Change-Id: I88b5e9f16b79e1e731056c45da6b5e1448d2c0e7
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4341
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The Ultrascale series is a bit more complicated to handle since with the
stacked and interconnected dies the IR gets longer. This adds support
for all currently known chips from the Ultrascale family.
Change-Id: Ibac325dd6fadc76f73cc682b1c62c1a5f39f0786
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4188
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.
Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
provide meta information for the cpsr so gdb can display the status
flags and not only a hexadecimal number
Change-Id: I9d3fb29153780adbea389d7e4175d5e19bddc256
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4460
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
and move declaration of all transport_is_xxx() functions to transport.h
Change-Id: Ib229115b5017507b49655bc43b517ab6fb32f7a6
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4469
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Since OpenOCD basically allows to perform arbitrary actions on behalf of
the running user, it makes sense to restrict the exposure by default.
If you need network connectivity and your environment is safe enough,
use "bindto 0.0.0.0" to switch to the old behaviour.
Change-Id: I4a4044b90d0ecb30118cea96fc92a7bcff0924e0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4331
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
If we enter debug state from EL0, some registers are not accessible.
Temporarily move to EL1H and back to gain access. Also, fix
armv8_dpm_modeswitch() to not immediately restore the previous state
on elevating the privilege level.
Change-Id: Ic2a92109230ff4eb6834c00ef544397a5b7ad56a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4461
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
gdb assumes that a rtos can make any thread active at will in response
to a 'Hg' packet. It further assumes that it needs to step-over after
setting a breakpoint on frame #0 of any non-current thread. Both
assumptions are not valid for an actual rtos. We fake the step-over to
not trigger an internal error in gdb. See
https://sourceware.org/bugzilla/show_bug.cgi?id=22925 for details.
Change-Id: Ida60cd134033c1d58ada77b87fe664a58f61e2c0
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4448
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Normally, when a ctrl-c is received from gdb, a SIGINT is reported back
unconditionally to tell gdb that the target has stopped in response.
However when a rtos support was configured, the rtos awareness overwrote
the signal with an actual thread state, which gdb then ignored and got
stuck without the user able to interrupt.
Change-Id: I40fd62333e020a8c4d9df0079270e84df9c77f88
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4445
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Also uses calloc() for mpsse_ctx->write_buffer to prevent a false
positive valgrind report
"Syscall param ioctl(USBDEVFS_SUBMITURB).buffer points to uninitialised bytes(s)"
Change-Id: I91963371d15c21ea0fee4c40c1da86174db44520
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4418
Tested-by: jenkins
Although the leak is negligible, the clean heap on exit will ease
valgrind testing.
Change-Id: I3a7a9c8e8dc7557aa51d0b9caa244537e5e7007d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4410
Tested-by: jenkins
If OpenOCD command line contains -c shutdown, server_quit() is not called.
Though if -c init is also on command line, gdb_server is already initialized.
Call server_quit() on both successful and failure exit from command line.
Change-Id: I6df41c5df045b61d84a5515d1abaa5dc96bc30ac
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4409
Tested-by: jenkins
Make sure the user is aware he can lock the device though unlock is not
possible without access to MDM-AP.
Change-Id: I92676530e95d19489c6739748a99c2895849f90f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4403
Tested-by: jenkins
