Directory listings are volatile and serve no purpose in the
manual. Just remove them.
Change-Id: I63d54ba209c29eafb6608cf406b8ce5d8e9ee6c8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2768
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Split TMS570 target into LS31/LS21 and LS20/LS10 targets.
Board for the TMS570LS20SUSB Kit, which uses the TMS570 Cortex-R4 MCU from TI.
Tested attaching.
Change-Id: I1a69ac1ed800d0d6b7f9860c19cbd149e3e47620
Signed-off-by: Alex Ray <a@machinaut.com>
Reviewed-on: http://openocd.zylin.com/2089
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Since mqx comes last in the list, with the auto option its
update_threads is called even though it wasn't detected.
This check should be removed from all the rtos helpers and moved to
the generic code, but better do it later all in one go.
Change-Id: If24ab42a58a468d90e9f12028d4c2fb76a9bc2e8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2741
Tested-by: jenkins
It was observed on AM437x that after every reset the target's debug
regions are unpowered. To be able to properly communicate with the
target and perform cortex_a init debug access after a reset event the
examination need to be performed every time, not just on OpenOCD
start.
Change-Id: Idf272e127ee88341e806ee00df154eade573451d
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2723
Tested-by: jenkins
Reviewed-by: Felipe Balbi <balbi@ti.com>
After intermittent connection failures or target power failures it
might be necessary to try reexamination even when polling fails. This
should make communication with Cortex-A targets more reliable.
This was runtime tested with stlink attached to an stm32l1 and an FTDI JTAG
adapter attached to an stm32f1 target.
Change-Id: I38c4db8124b7f4bbf53ddda53c13273449f49c15
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2721
Tested-by: jenkins
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Andreas Färber <afaerber@suse.de>
This adds support for the new Atmel SAML21 family of low-power Cortex
M0+ devices. Their Flash controller is essentially the SAMDxx one so
the change consists of adding the new part IDs. Unfortunately the
device ID logic had a couple of mistakes in it that did not affect
anything on SAMD2x devices (due to 0 values expected there) but that is
a problem on L21, it's therefore addressed here and things should now
match the datasheets.
Tested on Amtel SAML21 Xplained Pro development kit against the included
SAML21J18A there. Also tested for regressions on a SAMD20 and SAMD21
using their dev kits.
Change-Id: I768f75e064b8656c15148730dacaa4c3acfc4101
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2690
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This adds the mandatory Info documentation for the driver as well as
the usage field.
As a clean up, this also includes freeing of the allocated memory
which results in a memory leak if probe is invoked multiple times.
Valgrind-tested.
Reported by Dmitry Shpak.
Change-Id: I2b1d9b9e8b069c6665b11d880b40ce19a1b26ce6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2694
Tested-by: jenkins
Reviewed-by: Дмитрий Шпак <disona@yandex.ru>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* also included example for flash usage information
Change-Id: Icf9defc25d38bf24567b1708138b83a8de1e0497
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Reviewed-on: http://openocd.zylin.com/2705
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Use mmw to manipulate only selected bits of the word. msb and mwb verify the
memory location and may error on PLLRDY set as a result of PLLON written.
Change-Id: I9a4c1e58f002a1e5e99be1bd34aac27ba65d111d
Reported-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2702
Tested-by: jenkins
Currently itmdump is not a production-quality code hence this hack
seems to be appropriate.
More robust handling is possible with libswo-based swodec tool that's
available from http://git.zapb.de/ .
This adds a new command line option -d N where N is a stimulus number
you want to dump (counting from 1).
The idea here is that if you're interested to live-monitor just a
single stimulus port, you can use this utility directly. If one wants
to demultiplex the TPIU stream, the following is proposed:
1. Use https://gitorious.org/multiplex/multiplex utility that can
accept binary data from a file/pipe/stdin and arbitrary number of TCP
connections. It simply mirrors all the incoming data to all the
accepted connections;
2. Use socat to connect itmdump to the proxy mentioned in 1. and then
either dump the results to separate files or share via their dedicated
TCP ports.
Example script (inspired by http://openocd.zylin.com/#/c/1662/ ,
enables and disables specific itm ports on demand):
for i in `seq 0 31`; do
while true; do
socat -U TCP-LISTEN:$((8000+$i)),reuseaddr \
SYSTEM:"echo itm port $i on | nc -q0 localhost 4444 > /dev/null; nc localhost 7777 | stdbuf -oL itmdump -d$((i+1))"
echo itm port $i off | nc -q0 localhost 4444 > /dev/null
done < /dev/null >&0 2>&0 &
done
Change-Id: Iaeb102436eaa5b106002083f2ffe758fb7bd83e5
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2537
Tested-by: jenkins
GP and EPOS EVMs do not provide xds100v2 on board,
rather they have a pin header which can be used
to attach any debug pod the user might want.
Change-Id: I61678c50900fbe0fab500ea42f85ecde7a490ded
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-on: http://openocd.zylin.com/2618
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
