In some cases, the FILEIO_NONE access mode may be useful as a parameter
to indicate that file access should be disabled. High-level routines can
use it to skip file access calls, as 'fileio_open' will fail presently
if called to open a file using this mode.
This patch eliminates duplicated code in the the NAND 'dump' and 'write'
by using the new static helper functions.
These changes also fix a possible memory leak in nand dump command, in
the case that the dump file failed to open.
Overall, the changes should be functionally equivalent, but the
resulting code will be easier to improve and extend further.
This patch provides helpers APIs that will eliminate duplicated code in
the the NAND 'dump' and 'write' commands by factoring their common code
into static helper functions. These helpers may be useful for creating
new commands, as shown in the final patch to 'verify' flash from a file.
Several previously unreported error conditions now generate messages and
propogate the return codes, such as when the file fails to open and bad
arguments are given. These changes will fix a possible memory leak in
nand dump command, in the case that the dump file failed to open.
Overall, the changes should be functionally equivalent, but the
resulting code will be easier to improve and extend consistently.
Rewrite buf_cmp to use memcpy for bulk of comparison. Add static
helper to perform comparison of trailing byte, which uses another
static helper to perform a maksed comparison. The masked comparison
helper is used by the buf_cmp_mask to simplify its loop.
Improve types to use void *, unsigned, and return bool.
Don't include "target.h" from more headers than necessary. This
avoids needless interdependencies and duplicated include paths.
Don't needlessly include it in source files, either.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Same deal: "register.h" got needlessly included all over the
place because of being in a few widely included headers.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also, don't need that extra "types.h" inclusion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Lots of files still include it, often through needless
duplicate inclusion of "log.h"; sigh.
This cleans up the inclusion graph a bunch, so there are
fewer inclusion paths, but it doesn't change much otherwise.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
downloadable algorithms actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Also: "algorithm.h" doesn't need to include "types.h" again;
it already comes from a different header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most files in the tree seem to have ended up including this,
and *quite* needlessly ... only code implementing or using
breakpoints actually needs these declarations.
So take it out of the header files which included it, and put
it in files which use it ... reduce needless interdependencies.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Now the ARM11 cores can use the renamed arm_checksum_memory()
and arm_blank_check_memory() routines ... do so.
Sanity checked with "flash erase_check" of both NOR banks on an
OMAP2420 ... the algorithm code dumped four lines of of "poll"
status after each of almost 520 blocks (yes, *very* annoying) but
gave plausible results after producing that spam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Three changes: remove ARM11_HANDLER() in favor of normal structure
initialization syntax; fix goofy indentation in that structure; and
don't needlessly export arm11_register_commands(), it's only called
through that method table.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The arm7_9_checksum_memory() and arm7_9_blank_check_memory()
routines are not actually specific to the ARM7 and ARM9 core
generations ... they can work for any core which can run
algorithms using basic ARM (not Thumb) instructions.
Rename them; move the declarations to a more generic site;
likewise move the code (and tidy it a bit in the process).
NOTE: the blank_check() method falsely returned a success
status (0) on one error path, when the algorithm failed.
Fixed this bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Previously this flag was stored in "target_type", so that for example
if there were two ARM7TDMI targets in a scan chain, both would claim
to have been examined although only the first one actually had its
examine() method called.
Move this state to where it should have been in the first place, and
hide a method that didn't need exposure ... the flag is write-once.
Provide some doxygen. The examine() method is confusing, since it
isn't separating one-time setup from the after-each-reset stuff. And
the ARM7/ARM9 version is, somewhat undesirably, not leaving the debug
state alone after reset ... probably more of an issue for trace setup
than for watchpoints and breakpoints.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Removes unused arm_jtag_buf_* helpers from arm_jtag.[ch]. These could
reappear if patches are provided to conver the tree to use them, but
this code should not be in the master tree until that series is ready.
Purge an unused routine from the tree and remove a layering violation.
If this code is needed, it should reappear somwhere in src/jtag/,
where struct scan_field gets defined.
