The method soft_reset_halt is optional; no need to add an
empty function.
Remove mips_mips64_soft_reset_halt() and move the TODO comment
in struct target_type.
Change-Id: Id541a75e7a08645568961d59b73a120c2238701f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7184
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use the new "adapter gpio" commands to configure the GPIOs used by the
bcm2835gpio driver. The driver supports only 1 chip (gpiochip0).
The reset function now honours the srst_open_drain and trst_open_drain
options.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I5b6c68b16362000cf5141a83394549d2bf3af108
Reviewed-on: https://review.openocd.org/c/openocd/+/7123
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The /dev/mem file descriptor can be closed without invalidating the
mappings so close as soon as possible.
munmap() all memory, either on error or from quit.
Signed-off-by: Steve Marple <stevemarple@googlemail.com>
Change-Id: I2b6a8365f554e332520fa77ccf076188083a932f
Reviewed-on: https://review.openocd.org/c/openocd/+/7122
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Still some config file uses deprecated commands.
Replace them with the new commands.
Change-Id: I6ccbfb832e0ad2012e9af160bd2d92ad104af2bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7181
Tested-by: jenkins
New GCC reports 5 warning:
src/jtag/drivers/ep93xx.c: In function 'set_gonk_mode':
src/jtag/drivers/ep93xx.c:123:47: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
123 | devicecfg = *((volatile int *)(syscon + 0x80));
| ^
src/jtag/drivers/ep93xx.c:124:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
124 | *((volatile int *)(syscon + 0xc0)) = 0xaa;
| ^
src/jtag/drivers/ep93xx.c:125:35: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
125 | *((volatile int *)(syscon + 0x80)) = devicecfg | 0x08000000;
| ^
src/jtag/drivers/ep93xx.c: In function 'ep93xx_init':
src/jtag/drivers/ep93xx.c:182:46: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
182 | gpio_data_register = gpio_controller + 0x08;
| ^
src/jtag/drivers/ep93xx.c:183:56: warning: pointer of type 'void *' used in arithmetic [-Wpointer-arith]
183 | gpio_data_direction_register = gpio_controller + 0x18;
| ^
Change pointer type to allow pointer arithmetic.
Change-Id: Idd78a7156bdf99df2624043e924b8e54a0588ace
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7180
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The script configure.ac checks for the presence of system include
files required to build OpenOCD.
It incorrectly check for:
dirent.h
pthread.h
ifaddrs.h
net/if.h
that are never included by OpenOCD source code, plus the generated
macros:
HAVE_DIRENT_H
HAVE_PTHREAD_H
HAVE_IFADDRS_H
HAVE_NET_IF_H
are never used in OpenOCD source code.
It also checks for the system function:
vasprintf()
that is never called by OpenOCD source code, plus the generated
macro:
HAVE_VASPRINTF
is never used in OpenOCD source code.
Drop the checks for the unused system include files and the unused
system function.
Change-Id: I68c1b1a1be268a830247fc489f210877c32d7d23
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7175
Tested-by: jenkins
Commit c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr'
syntax change") replaces the jimtcl command "expr" with an openocd
version that detects the TCL syntax change and prints a warning.
The openocd "expr" command will be dropped after v0.12.0,
One side effect is that openocd invokes polling the target after
every openocd command, causing scripts that use several "expr"
commands to run much slower; see [1].
The proper fix would require openocd to invoke polling only at the
time period deadline, instead of at each command. Such fix is too
risky to be applied now, due to short time before v0.12.0-rc1.
As a temporarily workaround, let openocd to detect the "expr"
command and skip the polling.
This will be dropped together with the openocd "expr" command.
Change-Id: I8151aa28694817001046165a15475d64896f985e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/362/ [1]
Fixes: c7eaaf6204 ("openocd: prepare for jimtcl 0.81 'expr' syntax change")
Reviewed-on: https://review.openocd.org/c/openocd/+/7174
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Symbols that are not used outside the file should not be exported
and should be declared as static.
Change-Id: Icbe7f7bce287b903edec9dc9db3370722c51fbd5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7173
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Variables should not be declared in the include file, otherwise
multiple include will cause multiple instances.
Move the declaration in the C file and make it static.
Change-Id: I8b4884cba643a792a78df4e123aa324b19d92279
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7172
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Symbols that are not used outside the file should not be exported
and should be declared as static.
Move the existing comments to the static declarations.
Change-Id: Idf208e3fda4b3f8df789553cf03ebf5f20d811bb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7170
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Tested-by: jenkins
The function set_log_output() has never been used after the drop
of eCos build with commit 39650e2273 ("ecosboard: delete
bit-rotted eCos code") in 2012.
Drop it!
Change-Id: I070b688061776c7ced5db18f738d78a4a7623726
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7164
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
For some configurations, notably on DAP systems, resolve issue where single-stepping does not always transition into the HALTED state.
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I053f4eaffad8c3228878ba87580ada640e4bd2fe
Reviewed-on: https://review.openocd.org/c/openocd/+/7150
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Config files for DAP/JTAG and DAP/SWD systems
- Xtensa core config definitions for NXP RT685 with Xtensa HiFi DSP
Signed-off-by: Ian Thompson <ianst@cadence.com>
Change-Id: I9c3280052073d86e09c7553de661eb8662a95c4a
Reviewed-on: https://review.openocd.org/c/openocd/+/7145
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
