this device flash registers are quite similar to STM32L5
with this changes :
- flash size is up to 2MB
- 2MB variants are always dual bank
- 1MB and 512KB variants could be dual bank (contiguous addressing)
depending on DUALBANK bit(21)
- flash data width is 16 bytes (quad-word)
Change-Id: Id13c552270ce1071479ad418526e8a39ebe83cb1
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6108
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
this capability permits to program the flash if we cannot reserve a workarea.
the introduction the command 'stm32l4x flashloader <bank_id> [enable|disable]'
helps to automatically skip using the flashloader if needed.
Change-Id: Id29213c85ee5c7c487cfee21554f5a7ea50db6c9
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6273
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
this command will help to enable/disable or display the TrustZone security,
using the TZEN option bit.
Note: This command works only with devices with TrustZone, eg. STM32L5.
Note: This command will perform an OBL_Launch after modifying the TZEN.
Change-Id: I4aef15bf57d09c1658d37858143d23b1d43de1f0
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5542
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Use a command group 'ft232r' with subcommands instead of individual
commands with 'ft232r_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I0dbeb4716330c83f8ce89b0d054eb0286b887bdf
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6409
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'usb_blaster' with subcommands instead of individual
commands with 'usb_blaster_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I2ae3d96ba864c20d7db67c74677781a62bfc4eb5
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6407
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'buspirate' with subcommands instead of individual
commands with 'buspirate_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: Id999d4ba276af576fb22b76052f3c0a1f3e1b876
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6404
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'bcm2835gpio' with subcommands instead of individual
commands with 'bcm2835gpio_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I8f7b14273b1b2813ac3c9704605d175fa2053008
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6396
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'jtag_dpi' with subcommands instead of individual
commands with 'jtag_dpi_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I19271546235a3c6737f975976a0bf0a2f66cbbe7
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6394
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'xlnx_pcie_xvc' with subcommands instead of individual
commands with 'xlnx_pcie_xvc_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I0deaaa14ed14f65bf356f3c248331bfab472f08d
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6391
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'presto' with subcommands instead of individual
commands with 'presto_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I883d8d87fd457d29cee8d12cd80f2e6c405e8f42
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6390
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'remote_bitbang' with subcommands instead of individual
commands with 'remote_bitbang_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I2692320f19c8a357112a365db6ca7e13cd6ad411
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6389
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'openjtag' with subcommands instead of individual
commands with 'openjtag_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: Ie1b1bf0b7c03e7703cfb074e554288384bf7b1b9
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6387
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'parport' with subcommands instead of individual
commands with 'parport_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I4cb7096a8ba8d6cd7a6dc970862cd73c32b5c0a2
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6385
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds documentation for the bcm2835 interface configuration
parameters to the user manual. Documentation format is based on
the FTDI interface section, and was taken from the descriptions
in the driver source code.
Change-Id: I77b09b8bd44d8e8fe9cc5fb9de3c3a30550d943c
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6376
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Due to Freenode takeover it's likely that most of our users are going to
seek support on Libera in the nearest future.
Change-Id: I98db95bab51f4ef2ac854bf521468d22b2794e56
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/6297
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marc Schink <dev@zapb.de>
Use a command group 'ftdi' with subcommands instead of individual
commands with 'ftdi_' prefix.
The old commands are still available for backward compatibility but
marked as deprecated.
Change-Id: I93a0ae7070226cd2fdea566effeb14a141269de8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6332
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
- Added support for reading and writing 64-bit data items
using TCL commands "mem2array" and "array2mem". Until now,
data items only up to 32 bits were supportd.
- Cleaned up functions target_array2mem() and
target_mem2array(), especially data types of variables
and variable declarations (scope).
Change-Id: Ia0ba427804f8fd8d7568f12714ab36984d6d5e24
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/6286
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Minor typos found by the new checkpatch boosted by the dictionary
provided by 'codespell'.
Change-Id: I7b4cae1798ff5ea048fcbc671a397af763fdc605
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6218
Tested-by: jenkins
With this patch, the Zephyr[1] RTOS is supported by OpenOCD.
As usual with support for other RTOSes, Zephyr must be compiled with
the DEBUG_THREAD_INFO option. This will generate some symbols
with information needed in order to build the list of threads.
The current implementation is limited to Zephyr running on ARM
Cortex-M processors. This is the only ARM variant supported by Zephyr
at the moment and is used on most of the officially supported boards.
[1] https://www.zephyrproject.org/
Change-Id: I22afdbec91562f3a22cf5b88cd4ea3a7a59ba0b4
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-on: http://openocd.zylin.com/4988
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
IPDBG are utilities to debug IP-cores. It uses JTAG for
transport to/from the FPGA. The different UIs use TCP/IP
as transport. The JtagHost makes the bridge between these
two.
Comparable to the bridge between GDB and the in-circuit-
debugging-unit of a micro controller.
Change-Id: Ib1bc10dcbd4ea426e492bb7b2d85c1ed1b7a8d5a
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: http://openocd.zylin.com/5938
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
