This adds the ability to support srst reset for the stlink/v2.
stlink/v1 will fallback to using SYSRESETREQ which is a full reset - including peripherals.
To enable the use of the srst add the following to your cfg:
reset_config srst_only
Change-Id: I570de607c5f370fd6a4abf47360686c9be07bcdd
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/581
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The STLINK/V2 supports two api's.
This completes the support so STLINK_JTAG_API_V2 is usable.
Support for hardware srst still needs adding.
Change-Id: Ic4d0499be2a225d18abf96fd6f5ce5e295fb1f37
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/561
Tested-by: jenkins
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The first available devkits for the at91sam3x8h had the ES device populated.
The ES device had an error in the CIDR, specifically in the last byte of
which the upper 3 bits identifies the chip family - cortex-m3, arm7tdmi etc.
The problem was fixed on the ES2 devices - Thanks to Pat Hickey for giving me
the heads-up.
Change-Id: I13dd7fbe0cffaf76f948188c9459dc3cf4435570
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/575
Tested-by: jenkins
Reviewed-by: Jim Norris <u17263@att.net>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The value returned from target_write_buffer is still ignored.
Change-Id: Icb49d4d1313a5e4f7df68d3f122a5f81cfa0604a
Signed-off-by: Linus Tolke <linus@tigris.org>
Reviewed-on: http://openocd.zylin.com/596
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
In Section 2.7 USB ST-LINK based made these two changes:
"they only works with" to "they only work with"
"following method's" to "following methods"
Change-Id: Idfe6c11c3fa6f2157d01697cd7f480a9d495c8e2
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/590
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
since gerrit 2.3 pushing changes to refs/for/ is deprecated in
favour of using refs/publish/.
Change-Id: I6244b9645da2144921583bd9778a95c563fac89f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/567
Tested-by: jenkins
Use one board file per eval board, so that the filename matches the
exact board the user has / wants to use. Merging different boards into
one file is confusing.
Change-Id: I7c50233924a87a913723d7215c4851039c2971bc
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/566
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added the Flyswatter2 to section 2.3 USB FT2232 Based hardware
list.
Change-Id: I6a382644b5a0313d30afb5a97d0a9ea00f01efa9
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-on: http://openocd.zylin.com/584
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When following the Patch Guidelines step by step,
an error occurs at step 6.
"git pull --rebase origin/master" results in the error:
fatal: 'origin/master' does not appear to be a git repository
Removing the / seems to fix this.
Change-Id: I4e2fa23c60654abeaebd3b25a8c8375aa07b0abd
Signed-off-by: Bill Traynor <wmat@alphatroop.com>
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://openocd.zylin.com/574
Reviewed-by: David Anders <danders.dev@gmail.com>
Tested-by: jenkins
