Otherwise the new alignment checking algorithm thinks that the
address is not aligned, because it is way beyond the last sector.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This config is only lightly tested, and doesn't work well yet;
but it's a start.
* Notably missing is PLL configuration, since each DaVinci
does that just a bit differently; and thus DDR2 setup.
* The SRST workaround needed for the goof in the CPLD's VHDL
depends on at least the not-yet-merged patch letting ARM9
(and ARM7) chips perform resets that don't use SRST.
So this isn't yet suitable for debugging U-Boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.
Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.
We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates the board configuration for the SAM9-L9260 board with the
configuration for the on-board NAND and dataflash. Included are commands
for configuring the AT91SAM9 NAND flash driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Misc:
- Introduce some "struct reg" temporaries, for clarity
- Shorten lines
- Add some missing whitespace
- Clean up comments
- Add notes about some fault handling issues
- Most of these errata workarounds are for *OLD* chip revisions
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
And add my copyright. MPCore is untested, but it's the
only other ARM11 core to care about.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Command "reset halt" checks if PC properly resets, issueing warning:
"PC was not 0. Does this target need srst_pulls_trst?".
Checking PC against 0 is not always correct.
Removed PC value check, as suggested by Øyvind Harboe.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: U-PROPRIET-28D9DF\PROPRIETAIRE <PROPRIETAIRE@propriet-28d9df.(none)>
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip. This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
In conjunction with manual register setup, this lets the ETM trigger
cause entry to debug state. It should make it easier to test and
bugfix the ETM code, by enabling non-trace usage and isolating bugs
specific to thef ETM support. (One current issue being that trace
data collection using the ETB doesn't yet behave.)
For example, many ARM9 cores with an ETM should be able to implement
four more (simple) breakpoints and two more (simple) watchpoints than
the EmbeddedICE supports. Or, they should be able to support complex
breakpoints, incorporating ETM sequencer, counters, and/or subroutine
entry/exit criteria int criteria used to trigger debug entry.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Change handling of the CYCLE_ACCURATE, BRANCH_OUTPUT, and
TRACE_* flags; also the CONTEXTID size values.
- Convert to symbols matching the actual register bits, instead of
some random *other* bits (and then correcting that abuse).
- Get rid of a now-needless enum.
- Keep those values in etm->control, and remove etm->tracemode.
These values all affect the trace data that's recorded by a trace
pod or in the ETB. I modified the file format used to dump ETB
data; since it's fairly clear nobody can use this mechanism now,
this can't cause anyone trouble.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Provide better comments for the ETM_CTRL bits; use the correct bit
for half/full clock mode; and define a few more of the bits available
from the earliest ETM versions.
The new bit defintions use ETM_CTRL_* names to match their register
(instead of ETM_PORT_* or ETMV1_*). For clarity, and better matching
to docs, they are defined with bitshifting not pre-computed masks.
Stop abusing typdefs for ETM_CTRL values; such values are not limited
to the enumerated set of individual bit values.
Rename etm->portmode to etm->control ... and start morphing it into a
single generic shadow of ETM_CTRL. Eventually etm->tracemode should
vanish, so we can just write etm->control to ETM_CTRL.
Restore an "if" that somehow got dropped.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
