dap_configure() contained first time init related tasks, as the call to
dap_init_instance() and the check for configured tap.
Move all first time init related stuff to dap_create() to make dap_configure()
usable in eventual stand-alone 'dap configure' command.
Change-Id: Ia86eadb4e960ce54e8581630d01af75720d2318d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6702
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This is a preparatory change for swd multidrop, mostly refactoring.
Split swd_queue_dp_read/write() to inner and outer parts.
Use the inner parts in swd_queue_dp_bankselect(), swd_connect()
they do not need to check reconnect.
Use the outer parts exclusively in swd_dap_ops.
Rearrange the code to reduce forward declarations.
Change-Id: I47b7f0cb037e0032a267463f06ba02123ba96fe7
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6139
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Ignore ack received after DP_TARGETSEL write to prevent false error.
This change also fixes a bug:
Received ACK FAULT or JUNK value were incorrectly stored to queued_retval
and later used as bitbang_swd_run_queue() error return.
Use LOG_ERROR for parity mismatch.
Change-Id: I5ff1f658f221af78d8bbec8416a7a0fc64ba2550
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6700
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
According to ARM IHI0031C+ chapter 2.3.11 "TARGETSEL, Target Selection register"
multidrop capable DPv2 must not drive SWDIO line during the response phase
of a write to TARGETSEL register.
Introduce helper functions swd_cmd_returns_ack() and swd_ack_to_error_code()
to centralize these tests from all drivers to one place.
Introduce distinct error codes for SWD protocol.
Partly inspired by Graham Sanderson's http://review.openocd.org/4935
Change-Id: Ie5f9edb22e066a933a534bf2b29e7e1d3087dad1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6699
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
hla_layout.h uses explicitly tpiu_pin_protocol enum defined in
arm_tpiu_swo.h.
To make this header file consistent, add the missing include.
Change-Id: Ibecc279da8d6859ced2b8377e812554c747d81bb
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6687
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Added "jtag_vpi:" prefixes to log messages from the jtag_vpi
driver. The intention is to make it clear what the messages
relate to. Without the prefix, many of the log messages
won't make much sense to the user.
This change does not alter any functionality, just
the printed text.
Example:
Before:
Error: Can't connect to 127.0.0.1 : 5555
After:
Error: jtag_vpi: Can't connect to 127.0.0.1 : 5555
Change-Id: I779c379f52722b094b200d08b25ab0f7280d2845
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6686
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Today's version of jimtcl includes a fix for autoconf >= 2.70 and
a minor fix for warnings with GCC 11.
To prepare for next jimtcl 0.81, let's merge and test the updated
master branch.
Change-Id: I455cc708f7d4786461978e38b6ac71816e2c9825
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6674
Tested-by: jenkins
Add the value DORMANT_TO_JTAG in the enum listing the SWJ-DP
switching sequences.
The corresponding bit-sequence is already available.
Change-Id: I6f1ffd29a8f5729ec70ce0303248bc251409d37d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6689
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
If the target is in a state where S_REGRDY polling is necessary (slow
clock, low power state...?), OpenOCD will continue to use the slow
path even if the condition is temporary and the target at a later
point would be capable of fast reads again.
Revert to fast reads if a full register dump can be made without need
for polling any of the registers; presumably it will succeed the next
time too.
Change-Id: I557f0d90b7ce6f9d81aa409b6400fc9c83d16008
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6678
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Without the change cortex_m_debug_entry() reads all registers
calling cortex_m_load_core_reg_u32() for each register with
a poor usage of JTAG/SWD queue.
It is time consuming, especially on an USB FS based adapter.
Moreover if target_request debugmsgs are enabled, DCB_DCRDR
is saved and restored on each register read.
This change introduces cortex_m_fast_read_all_regs()
which queues all register reads and a single dap_run() transaction
does all work.
cortex_m_fast_read_all_regs() reads all registers unconditionally
regardless register cache is valid or not. This is a difference
from the original cortex_m_debug_entry() code.
cortex_m_debug_entry times from -d3 log, Cortex-M4F and CMSIS-DAP
(Kinetis K28F-FRDM kit)
target_request | time [ms]
debugmsgs | without the change | with the change
---------------+--------------------+-----------------
disable | 186 | 27
enable | 232 | 29
Added checking of DHCSR.S_REGRDY flag. If "not ready" is seen,
cortex_m->slow_register_read is set and fallback to the old
register read method cortex_m_slow_read_all_regs() is used
instead of cortex_m_fast_read_all_regs().
Change-Id: I0665d94b97ede217394640871dc451ec93410254
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5321
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Accordingly to arm documentation [1], chapter C1.6.4, the
operation to read/write from/to core registers can require time,
and the specific flag DHCSR.S_REGRDY has to be polled to verify
that the operation has been completed.
The lack of check on S_REGRDY causes OpenOCD to fail handling
correctly the core registers on a Cortex-M4 emulated in a slow
FPGA, and it could also fail on devices clocked at very low speed
while using a fast adapter.
Poll S_REGRDY as specified in [1] while either reading or writing
the core registers.
A timeout of 0.5s is added. This could still be too small in some
extremely slow cases, but at least now we log the timeout event,
which can help tracking down such odd issue.
During register read include in the polling loop the read of DCRSR
and to flush the JTAG queue only once.
During register write, relax the write in DCRSR by removing the
atomicity that is now useless since followed by the atomic read to
S_REGRDY.
During register read include the read of DCRSR inside the polling
loop to relax the read of S_REGRDY since followed by the atomic
read to DCRSR.
This change has the drawback of adding other transfers to the
adapter while reading/writing the registers, so it is expected to
introduce some speed degradation during step-by-step.
[1] DDI0403E - "ARMv7-M Architecture Reference Manual"
Change-Id: I61f454248f11a3bec6dcf4c58a50c5c996d7ef81
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/5319
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
DCB DHCSR register contains S_RETIRE_ST and S_RESET_ST bits cleared
on a read.
The change introduces a helper function cortex_m_cumulate_dhcsr_sticky().
Call this function each time DHCSR is read to preserve S_RESET_ST state
in the case of a reset event was detected.
Introduce cortex_m_read_dhcsr_atomic_sticky() convenience helper to
read DHCSR, store it to cortex_m->dcb_dhcsr and cumulate sticky bits.
The cumulated state of S_RESET_ST is read and cleared in cortex_m_poll()
Change-Id: Ib679599f850fd219fb9418c6ff32eed7cf5740da
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6180
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
cortex_m_single_step_core() used mem_ap_write_atomic_u32() to manipulate
dhcsr bits unlike the rest of code, where a specialized function
cortex_m_write_debug_halt_mask() takes place.
Unify setting of dhcsr bits and use cortex_m_write_debug_halt_mask() here as well.
Extracted from [1].
[1] Antonio Borneo: 6207: cortex_m: rework handling of dcb_dhcsr
Link: https://review.openocd.org/c/openocd/+/6207
Change-Id: I9ef05ce88a9dce42e1d3d5404a4fe87ec86b5fe8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/6676
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
