Change jtag_rclk behaviour so it can be called before the interface init function
git-svn-id: svn://svn.berlios.de/openocd/trunk@2590 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- remove endianness options; these chips hard-wire "little"
- $_TARGETNAME updates:
* don't pass $_TARGETNAME where a TAP label is required
* flash config uses $_TARGETNAME (it might not be target #0)
* simplify one $_TARGETNAME construction
- update work area setup:
* remove VM spec; these chips have no VM!
* fix some wrong sizes (0x4000 == 16K, not 4K)
* simplify: take defaults
- comment fixups
git-svn-id: svn://svn.berlios.de/openocd/trunk@2589 b42882b7-edfa-0310-969c-e2dbd0fdcd60
issue with this is that the core debug support uses this
mechanism, then trashes its state over reset. Users can
Work around that (for now) by re-assigning the desired
config after reset.
Also fixes "target halted due to target-not-halted" goof.
When we can't describe the reason using OpenOCD's limited
vocabulary, say "reason undefined" instead of saying it's
not halted.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2588 b42882b7-edfa-0310-969c-e2dbd0fdcd60
arrays (error prone) or assume all registers are 32-bits wide (they can
have fewer bits); don't use spaces in register names, so they can be
passed more easily to the "reg" command.
Minor updates for ARM9 vector_catch support: it's an 8-bit value. This
seems to help this core's vector_catch command work a bit better; but its
behavior wih the register cache is still goofy.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2587 b42882b7-edfa-0310-969c-e2dbd0fdcd60
display them as 32 bits unless that's their true size.
(Removes some confusion.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2586 b42882b7-edfa-0310-969c-e2dbd0fdcd60
OpenOCD was able to access only to chips attached to first EMIF
chipselect. This patch fixes chipselect management code and allows
OpenOCD to access to NAND devices attached to any EMIF CS line.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2585 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add flash programming support for NXP LPC1700 cortex_m3 based family
git-svn-id: svn://svn.berlios.de/openocd/trunk@2579 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Warn about anyone using "jtag_speed" commands; that command is obsolete, and will someday be removed.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2578 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- revert patch from rev1507 as it was causing reset issues with arm9 cores
git-svn-id: svn://svn.berlios.de/openocd/trunk@2574 b42882b7-edfa-0310-969c-e2dbd0fdcd60
A5.3.11 Data processing (shifted register)
The usual kinds of problems; the most noteworthy were that
the "S"et flags bit was mis-handled in these instructions.
---
This is the last patch from a quickie set of tests covering all
encodings of the instructions with 32-bit opcodes. There may
be some corner cases left, plus the instructions that aren't
yet handled, but the Thumb2 disassembler is no longer just
"lightly" tested with GCC output ... the new code paths have
mostly been verified.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2568 b42882b7-edfa-0310-969c-e2dbd0fdcd60
A5.3.5 Load/store multiple
A5.3.7 Load word
There was a longstanding bug in Thumb-1 LDM; the rest of the LDM/STM
fixes are just using width specs to match UAL syntax, except for two
opcode name typos. Load word had two bitmask goofs.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2567 b42882b7-edfa-0310-969c-e2dbd0fdcd60
A5.3.8 Load halfword, unallocated memory hints
It's mostly the usual sort of bitmasking goofage and getting the
width specs right. In one case an older x86 GCC generated bad code
unless I structred a conditional differently (sigh).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2566 b42882b7-edfa-0310-969c-e2dbd0fdcd60
