This command permits the usage of a TCP port to perform debug and stdio
operations:
- debug : READC, WRITEC and WRITE0
- stdio : READ, WRITE
This will permit the separation of semihosting message from OpenOCD log,
and separate semihosting messages per core.
syntax: arm semihosting_redirect (disable | tcp <port> [debug|stdio|all])
this allows to select which operations to be performed via TCP (debug,
stdio or all (default)).
Note: for stdio operations, only I/O from/to ':tt' file descriptors are
redirected.
tested using netcat on ubuntu
Change-Id: I37053463667ba109d52429d4f98bc98d0ede298d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/5562
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace 'mem2array' and 'array2mem' with a Tcl wrapper that
internally uses 'read_memory' and 'write_memory'.
The target-specific 'mem2array' and 'array2mem' functions
remain for now.
Change-Id: If24c22a76ac72d4c26916a95f7f17902b41b6d9e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6308
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
These functions are meant as replacement for 'mem2array' and
'array2mem'.
The main benefits of these new functions are:
* They do not use Tcl arrays but lists which makes it easier
to parse (generate) the data. See the Python Tcl RPC code
in contrib as a negative example.
* They do not operate on Tcl variables but instead return (accept)
the Tcl list directly. This makes the C and Tcl code base
smaller and cleaner.
* The code is slightly more performant when reading / writing
large amount of data. Tested with a simple Python Tcl RPC
benchmark.
Change-Id: Ibd6ece3360c0d002abaadc37f078b10a8bb606f8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/6307
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Enabling a portion (0x100 - 0x107) of the user defined semihosting
operation number range (0x100 - 0x1FF) to be processed with the help of
the existing target event mechanism, to implement a general-purpose Tcl
interface for the target available on the host, via semihosting
interface.
Example usage:
- The user configures a Tcl command as a callback for one of the newly
defined events (semihosting-user-cmd-0x10X) in the configuration
file.
- The target can make a semihosting call with <opnum>, passing optional
parameters for the call.
If there is no callback registered to the user defined operation number,
nothing happens.
Example usage: Configure RTT automatically with the exact, linked
control block location from target.
Signed-off-by: Zoltán Dudás <zedudi@gmail.com>
Change-Id: I10e1784b1fecd4e630d78df81cb44bf1aa2fc247
Reviewed-on: https://review.openocd.org/c/openocd/+/6748
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some CPU wrongly indicate the bypas bit in the codeid.
It's the case of the NanoXplore NG-ULTRA chip that export a
configurable (and potentially invalid) ID for one of
its component.
Add an option to ignore it.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Change-Id: Ic59743f23bfc4d4e23da0e8535fec8ca9e87ff1a
Reviewed-on: https://review.openocd.org/c/openocd/+/6802
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
With jimtcl 0.81 the syntax of the TCL command 'expr' requires the
multiple arguments to be within curly brackets.
Update the examples in the documentation to follow the new syntax.
While there, split one example to avoid it to exceed the line size
during pdf document generation.
Change-Id: I91cca419f8273415ccb0c2ce369fc6ac476e34e5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6809
Tested-by: jenkins
Changed flash driver to support writing to the user data page, as well as to any portion of the lockbits page above 512 bytes (the amount used for the actual page lock words). The top part of the lockbits page is used on at least the EFR32xG1 chips for the SiLabs bootloader encryption keys.
As presented to the user, the lockbits page is the same size as the other pages, but any attempt to write to its low 512 bytes is an error. To enforce this, efr32x_write is renamed to efm32x_priv_write and a wrapper function is provided in its place. If the user erases the lockbits page, the driver rewrites the cached lock words after the erase. When the driver erases the lockbits page in order to update the lock words, it first takes a copy of anything stored in the top part of the page, and re-programs it after the erase operation.
There are now multiple instances of flash_bank for each target, and the flash_bank instances must share their cached lock words to operate as intended. Therefore, when a bank is created, the global flash bank list is used to find any other banks that share the same target. Since some banks in the global list are invalid at the time free_driver_priv is called, reference counting is used to decide when to free driver_priv.
To avoid the need to find the lockbits flash_bank from another flash_bank, efm32x_priv_write and efm32x_erase_page now take an absolute address.
There didn't seem to be any reason to prohibit unprotecting individual flash pages, so that limitation is removed from efm32x_protect().
This addresses ticket #185.
Valgrind-clean, except for 2x 4kiB not freed/still reachable blocks that were allocated by libudev.
No new Clang analyzer warnings, no new sanitizer warnings.
Signed-off-by: Doug Brunner <doug.a.brunner@gmail.com>
Change-Id: Ifb22e6149939d893f386706e99b928691ec1d41b
Reviewed-on: https://review.openocd.org/c/openocd/+/6665
Tested-by: jenkins
Reviewed-by: Fredrik Hederstierna <fredrik.hederstierna@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
- "riscv set_prefer_sba" - removed from the doc, superseded
by the latter
- "riscv set_mem_access" - new command, new entry added
into the doc
This change only addresses the documentation. The corresponding
implementation of the RISC-V commands is already merged.
Change-Id: I3c07672cde94324407cf667504dba5402f63a543
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6743
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
These commands were extended/improved in the last drop
of RISC-V target updates. Update also the documentation
to properly describe how the commands should be used now.
Change-Id: I9e2ba6adbe1a4c032b96f5f8ff2d4791fa4c2527
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6738
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tim Newsome <tim@sifive.com>
Document both find and ocd_find command under Config File Guidelines
-> Interface Config Files. find command is used in the previous
section as well but the previous section is more about using OpenOCD.
The section added is "aimed at any user who needs to write a config
file".
Change-Id: I698207fe58d564c615a15b50756aa5547a5f40b7
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6737
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Document "command mode" command Server Configuration -> Configuration
Stage. The text is taken from command's help string.
In addition to the help string, this commit explain the words
mismatch, the doc uses "stage" but the command and source code uses
"mode" to describe the same thing.
Change-Id: I1d5fc8c64a3a0b07ea8430bf016bcbd54e52da1c
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6736
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Document usage command under General Commands -> Server Commands. The
text is taken from the command's help string.
Change-Id: I957cb46cca98181c3c5e676228c5c103e47bb655
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6735
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Document add_help_text and add_usage_text under Genral Commands ->
Misc Commands. The text are taken from command's help strings.
Change-Id: I2bbbee8e5faa8d9654227c304e0528f5144275e8
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6734
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Now that adapter serial is handled independently from the adapter
drivers, move inside jtag_libusb_open() the call to
adapter_get_required_serial(), so every adapter that uses libusb
will automagically get USB serial support.
Extend the documentation to list the adapters involved.
Change-Id: I75b3482d38f8ed3418329f3106c5e8b689fd460b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6663
Tested-by: jenkins
The driver hla defines the command 'hla_serial' to specify the
serial string of the adapter.
The driver st-link defines the command 'st-link serial' to specify
the serial string of the adapter.
Remove and deprecate the driver commands and use 'adapter serial'.
Change-Id: I9505c398a77125b1ebf4ba71da7baf4d663b75be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6657
Tested-by: jenkins
