Most commands are usable only at runtime; so don't bother saying
that, it's noise. Moreover, tokens like EXEC are cryptic. Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are
- Configuration commands (per documentation)
- And also some commands that valid at *any* time.
Update the docs to note that "help" now shows this mode info.
This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been. This just fixes ones I noted when sanity testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This makes it so that the usage/help command properly uses the whole command,
including subcommand, in the search for help information. This previously
caused erroneous output from the usage command handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I wanted to make it so I can be ignorant of a commands invocation string, so
I tried to use CMD_CURRENT (aka cmd->current) which is supposed to house a
pointer to the current command. It turns out that this wasn't being set.
This patch adds the current command structure to the command invocation
structure before sending it along to the command handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The relevant cable config is already in OpenOCD, but not a config for
the JTAG adapter. I have tested with FlashLINK on ARM926.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds the .settings folder and the .cproject file put down
by Eclipse from the eyes of Git.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Handlers for commands
- arm7_9 semihosting <enable | disable>
- $_TARGETNAME arp_reset assert 1
didn't check if target has already been examined, and could
segfault when using the NULL pointer "arm7_9->eice_cache".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The handler for "arm9tdmi vector_catch ..." did not check
if target has already been examined. Without this fix it
segfaults when using NULL pointer "arm7_9->eice_cache".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:
- Recent rev C lm3s811 eval boards didn't work. They must use
the ICDI layout, which sets up some signals that the older
boards didn't need. This is actually safe and appropriate
for *all* recent boards ... so just make "luminary.cfg" use
the ICDI layout.
- "luminary-lm3s811.cfg", was previously unusable! No VID/PID;
and the wrong vendor string. Make it work, but reserve it
for older boards where the ICDI layout is wrong.
- Default the LM3748 eval board to "luminary.cfg", like the
other boards. If someone uses an external JTAG adapter, all
boards will use the same workaround (override that default).
The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it. Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Otherwise the new alignment checking algorithm thinks that the
address is not aligned, because it is way beyond the last sector.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This config is only lightly tested, and doesn't work well yet;
but it's a start.
* Notably missing is PLL configuration, since each DaVinci
does that just a bit differently; and thus DDR2 setup.
* The SRST workaround needed for the goof in the CPLD's VHDL
depends on at least the not-yet-merged patch letting ARM9
(and ARM7) chips perform resets that don't use SRST.
So this isn't yet suitable for debugging U-Boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.
Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.
We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates the board configuration for the SAM9-L9260 board with the
configuration for the on-board NAND and dataflash. Included are commands
for configuring the AT91SAM9 NAND flash driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
