Remove list of id codes for all families.
Maintain a list with id, bscan-length and check position
in the tcl config files for each family.
The Intel FPGA Driver option 'family' is not otional anymore.
Change-Id: I9a40a041069e84f6b4728f2cd715756a36759c89
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/8083
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Probes all flash and UICR areas.
Flash erase and write tested.
On nRF53 mass erase works on the application core flash bank only.
The Tcl script nrf53_recover can serve as the workaround on the
network core.
TODO: mass erase of the nRF53 network core flash.
Some ideas taken from [1] and [2].
Change-Id: I8e27a780f4d82bcabf029f79b87ac46cf6a531c7
Link: [1] 7404: flash: nor: add support for Nordic nRF9160 | https://review.openocd.org/c/openocd/+/7404
Link: [2] 8062: flash: nor: add support for Nordic nRF9160 | https://review.openocd.org/c/openocd/+/8062
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8112
Reviewed-by: Tomáš Beneš <tomas@dronetag.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The link to product GW16042 was broken, so it has been reduced to
the manufacturer's website, which fixes the warning as a side effect.
The link to Raisonance RLink was broken, and the new one is shorter,
which fixes the warning as a side effect.
Change-Id: I4df9acf2d994d51cd8f375bdac6c803270029506
Signed-off-by: R. Diez <rdiezmail-openocd@yahoo.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8264
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To help readability and discriminate the 'then' block from the
multi-line condition, suggest to increase the indentation of the
condition.
Change-Id: I02e3834be3001e7ecf24349ad3cefe94b27b79c8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8199
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
It was noticed that the remote_bitbang protocol has a design issue:
SWD and sleep commands cannot be implemented at the same time, because
they overlap:
- SWD uses d,e,f,g for setting pin state
- sleep uses d,D for microsecond and millisecond sleep, respectively
This has previously been reported by Marek Vrbka, but it wasn't fixed.
This commit does the following to resolve the issue:
- Change the sleep commands to 'Z' for 1 ms, 'z' for 1 µs
- Document 'D' and 'd' as deprecated aliases
- Switch the remote_bitbang driver in OpenOCD to 'Z' and 'z'
Unfortunately that's a breaking change, because existing adapter-side
implementations of the protocol will have to implement the new commands
to keep working with future versions of OpenOCD. Fortunately, the
remote sleep commands haven't been part of an OpenOCD release yet,
which should limit the breakage somewhat.
Reported-by: Marek Vrbka <marek.vrbka@codasip.com>
Link: https://sourceforge.net/p/openocd/mailman/openocd-devel/thread/670d28d2-75a1-45ec-afe5-541415701d7a%40codasip.com/
Fixes: e8e09b1b5 ("remote_bitbang: add use_remote_sleep option to send delays to remote")
Change-Id: I04d2790a33bff9d47eb7f69b3275fd9a271625ae
Signed-off-by: J. Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.openocd.org/c/openocd/+/8191
Reviewed-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jeremy Herbert <jeremy.006@gmail.com>
To simplify the ipdbg start/stop command and be able to
add additional commands in the future, we introduce the
concept of a hub which has to be created before a
ipdbg server can be started.
The hub was created on the fly in previous versions.
Change-Id: I55f317542d01a7324990b2cacd496a41fa5ff875
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7979
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The command substantially complicates support of nRF53/91
series. It was not even properly ported to nRF52.
The informative value is disputable. Who wants to see
e.g. override trim values for radio or unique device ID?
Drop it and simplify the driver.
Change-Id: Ia7fb20ce2ebf16065705c5d18deaf934e58db426
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8108
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add GPIO extender initial configuration that is needed to configure
some important GPIOs and ensure that the dev board is ready to work.
Add i2c_write function that make a write transfer to any slave device.
Give a new Product ID to ANGIE to make it different than the non
programmed ANGIE.
Change-Id: I0a8dacb7fe218145b7d3ed1cb75f106ed6256714
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8072
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some OpenOCD command gets fragment of TCL scripts as command-line
argument, fragments that will be kept and executed later on.
E.g. the command 'configure' gets the body of an OpenOCD event:
$TARGET configure -event halted {TCL code}
These commands store the argument as a Jim_Obj and pass it to the
jimtcl interpreter when the TCL fragment has to be executed.
Using Jim_Obj as storage is relevant to let the jimtcl interpreter
to recover extra info of the TCL fragment, like the file-name and
the line-number that contain the fragment, that will be printed
out in case of run-time errors.
While converting the commands to COMMAND_HANDLER, we should avoid
storing the argument as C strings otherwise we will loose precious
info in case of run-time errors making challenging the debugging
of such TCL fragments.
Extend the struct command_invocation to contain the array that
points to the Jim_Obj of the command arguments.
This will be used while converting commands to COMMAND_HANDLER.
Change-Id: If37c5f20e9a71349f77ba1571baf1e6778e28aa5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8057
Tested-by: jenkins
S32K General-Purpose Microcontrollers
Scalable, low-power Arm® Cortex®-M series-based microcontrollers AEC-Q100
qualified with advanced safety and security and software support for
industrial and automotive ASIL B/D applications in body, zone control,
and electrification.
Change-Id: I4143258535437c18b81802436267bfd561de9d31
Signed-off-by: David Vidrie Leon <davidvidrie@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
