This config file add support to the opendous cable based on the chip ft2232H,
using the ftdi interface driver.
Change-Id: I4491f99d7b14f7078a04583ef0c4acd8692c4349
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1097
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rather than use bold fonts etc, use the correct keywords so doxygen formats
better.
Change-Id: Id9d63f0fc3465665376d7a536c4d6da71998f40e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1210
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
This fixes an issue if the device is manually probed after the initial probe
fails due to being unable to read flash size register. In this situation the
driver assumes the user has overridden the flash size when infact this may
not be the case.
It also seems on the older stm32f1 devices the flash register is not readable
when locked, this does not seem to apply to the newer parts - f0, f3, f4.
Change-Id: I125f872fcb2d962ca6705f97b62d957e2b31303b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1187
Tested-by: jenkins
Reviewed-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The stm32f0 and stm32f3 share the same option byte location, but the format
differs.
Adding an option_offset fixes the broken options_read cmd and incorrectly
setting Hardware Watchdog when unlocking a f3x device.
Change-Id: I82d66b6198294ea9eedb44ca8b2fb368c0cb15e8
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1184
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This change adds a simple target configuration for Freescale
single/dual/quad core i.MX6 SoCs, only one core is configured by default.
Change-Id: I853dd27f4c6765b7f731be2ddea82e85d496c6a4
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-on: http://openocd.zylin.com/1135
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When the ftdi driver calls finally the mpsse_flush function, it first
initiate the USB in and finally the corresponding USB out transaction.
Because data in is requested too early the USB device will always answer
the first USB in by a NAK. That can prevented by a simple reordering of
the out and then the in transfer and can improve the Jtag performance for
high JTAG clock rates.
Change-Id: I17abf1487c914c92e2e447ee6d30562ef629f327
Signed-off-by: Peter Henn <Peter.Henn@web.de>
Reviewed-on: http://openocd.zylin.com/942
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
This patch change the default reset config from SYSRESETREQ to the working
VECTRESET.
Change-Id: I21a9a74b9c0c68cfa3a6e6dac9b123acc98a93cb
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1186
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Move the global target back off timer to the target struct. This will
fix the wrong error handling with multi target devices like smp systems.
Change-Id: Ia327182ed5d13ca87323700017a8c40ecc6b25a3
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1179
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The USB buffer will need space for both TMS and TDI buffers.
Each holds tap_buffer_size bytes maximum, so tap_buffer_size must be
smaller than half of usb buf_size.
Change-Id: Id8f39936a894cbd98deb89eec5a859aef1e2b783
Signed-off-by: Joerg Fischer <turboj@gmx.de>
Reviewed-on: http://openocd.zylin.com/1136
Tested-by: jenkins
Reviewed-by: simon qian <simonqian.openocd@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Because we were always running using target state TARGET_RUNNING target
algorithm's were a bit verbose compared to other targets.
This brings the hla target inline with the other targets.
Change-Id: I3a257fdc878b87660fac8b5eca22b421eee5b349
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1134
Tested-by: jenkins
The was missed when the armv7m was moved over to using the std arm
core_cache, probably because it is disabled by default.
Change-Id: I2f5a18ef6dd783b36e8c29f4c52379104bda4583
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1138
Tested-by: jenkins
Added support for new ST devices in the stm32lx portfolio, with device
id 0x427. These have 256k flash, but in a single bank compared to
device id 0x436 which is a dual bank flash.
Change-Id: Iafdfe990f24bd04b0d6e00385ee70690f3bf8d5f
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1140
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This update adds support for the STM32Lx 384kb dual bank flash. Previously there was a problem when writing an
image that was larger than 192Kb. That lead to openocd printing out two error messages like
"Error: access denied / write protected" and "Error: invalid program address". The reason was that the stm32lx
driver tried to write half pages which overlapped into the next flash bank.
A new configuration file stm32lx_dual_bank.cfg can be used for stm32lx chips with dual bank flash (256kb or 384kb devices).
A sanity check was added for probed flash size values to fix the issue seen on some ST samples that answered incorrectly.
Change-Id: I69e25131983d88613be8606b438f98870c5f1e52
Signed-off-by: Johan Almquist <johan.almquist@assaabloy.com>
Reviewed-on: http://openocd.zylin.com/1125
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It has been seen on some stm32 targets that the flash size register that
is probed by the driver may contain an invalid size.
This change enables the user to override the probed value.
Change-Id: I09359e59a96f9133d3d939670957d32a830a944e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1132
Tested-by: jenkins
Reviewed-by: Johan Almquist <johan.almquist@assaabloy.com>
adapter_init (core.c) won't check speed configuration
of the selected interface if it's not needed (.speed = NULL).
When it's not needed, we can now omit adapter_khz in
init scripts and we don't have to implement dummy handlers
for speed_div and khz functions.
It also removes calls to adapter_khz in interface configuration
files when not used anymore.
Change-Id: I6eb1894385503fede542a368f297cec6565eed44
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1131
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Make sure we restore the core mode after executing any algorithm.
We also now check that we actually need to swap the core mode, we may
already be in the correct mode.
Change-Id: Ia48af2c108e0f9868aae241bf25f60323503f092
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1107
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
