SW-DPv2 and SWJ-DPv2 devices do not reply to DP_TARGETSEL write cmd.
Ignore the received ACK after TARGETSEL write.
While on it, use swd_ack_to_error_code() for unified error code
translation of the received ACK value for all other commands.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If978c88c8496e31581175385e59c32faebfd20aa
Reviewed-on: https://review.openocd.org/c/openocd/+/7383
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: zapb <dev@zapb.de>
Speed calibration coeffs are computed from cpufreq/scaling_max_freq
and from the device-tree compatibility information.
Raspberry Pi linux offers /dev/gpiomem for non-root access
to the GPIO registers since ~2016.
Do not configure 'bcm2835gpio peripheral_base' as it is necessary
only if /dev/mem is used - it requires running OpenOCD as root
- it's a security risk so it should be avoided.
The configuration of the GPIO connector (40-pin header)
is factored out and ready to use in interface configuration
for other driver (e.g. linux gpiod).
Mark raspberrypi2-native.cfg as deprecated and redirect
it to raspberrypi-native.cfg
Change-Id: Icce856fb660b45374e94174da279feb51f529908
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7264
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After setting adapter speed to some values, the driver
shows the real speed little bit higher.
Although it does not impose a problem from technical point
of view because the difference is smaller than usual speed error,
it looks at least strange to the user. The documentation reads
that real frequency should be same or lower than requested.
Use proper rounding in speed -> delay and delay -> speed
conversions.
Change-Id: I1831112cc58681875548d2aeb688391fb79fa37f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7261
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
bitbang_swd_exchange(rnw=true,...) calls bitbang_interface->swd_write()
with swdio clamped to 0.
bitbang_swd_write_reg() reads 1 turnaround bit, 3 ack bits
and 1 turnaround by one call to bitbang_swd_exchange()
and then switches SWDIO to output.
AFAIK all bitbang interfaces switch SWDIO GPIO direction immediately
in bitbang_interface->swdio_drive().
The GPIO now drives SWDIO line to the value stored in the output register
which is always zero from previous bitbang_swd_exchange(rnw=true,...).
In case the following data bit (bit 0) is 1 we can observe a glitch
on SWDIO:
_____ out 1 ____
HiZ/pull-up ----\ /
\ /
\______ out 0 ______/
swdio_drive(true) swd_write(0,1)
The glitch fortunately takes place far enough from SWCLK rising edge
where SWDIO is sampled by the target, so I believe it is harmless
except some corner cases where the reflected wave is delayed on long
line.
Anyway keeping electrical signals glitch free is a good practice.
To keep performance penalty minimal, pre-write the first data
bit to SWDIO GPIO output buffer while clocking the turnaround bit.
Following swdio_drive(true) outputs the pre-written value
and the same value is rewritten by the next swd_write()
instead of glitching SWDIO.
Change-Id: I72ea9c0b2fae57e8ff5aa616859182c67abc924f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7260
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The OpenJTAG driver logs "num_cycles > 16 on run test" warning
whenever the JTAG_RUNTEST operation cycle count is larger than 16.
Instead of logging the warning and only running the first 16 TCLK
cycles, remove the warning and queue up multiple operations of up
to 16 cycles each.
Signed-off-by: N S <nlshipp@yahoo.com>
Change-Id: Id405fa802ff1cf3db7a21e76bd6df0c2d3a0fe61
Reviewed-on: https://review.openocd.org/c/openocd/+/7420
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
URL for Microsoft documentation on IgnoreHardwareSerialNumber
redirects to generic USB driver landing page instead of specific
article. Update link to go to correct page.
Signed-off-by: N S <nlshipp@yahoo.com>
Change-Id: Ifac6c730a1438242cdfe0a0a2867e043e03ceec7
Reviewed-on: https://review.openocd.org/c/openocd/+/7439
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This generalizes the little endian CRC32 function used in the OR1K
target and moves it to a common helper, so that other places do not need
to reinvent the wheel. It is directly used in the OR1K target.
Change-Id: I0e55340281a5bfd80669bb1994f3a96fecc1248a
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7415
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Polling the target makes no harm during PSoC 4 flash write in the current
OpenOCD code. Don't mask it.
Change-Id: I6625ded0162ee3a96b92188844d0d2d6c30101c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7162
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
