In ChibiOS/RT 3.0 the ready list pointer "rlist" is now part of the system
data structure. Since the ready list is the first element in that
structure it can be accessed via the structure's symbol "ch".
Change-Id: Idc7eaa87cb7bbad0afa0ff1dafd54283bf429766
Signed-off-by: Christian Gudrian <christian.gudrian@gmx.de>
Reviewed-on: http://openocd.zylin.com/2352
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
is_erased can be one of -1, 0, or 1 so it must not be checked like a
boolean value. In this case we want to erase a page unless we know it's
already erased so we just check for is_erased != 1.
Thanks to Jim Paris for pointing this out on another driver.
Change-Id: I4591186228153b64e5a9608a2aac18745e578d4a
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/2368
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some J-Link fw versions require registration to be performed before
SWD operation is possible. It doesn't harm anyway, vendor's utilities
do it unconditionally.
Thanks go to Segger for providing the necessary information.
Change-Id: Iabd76c743eca86e2c817a97cb93c969fec3f7ac6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2331
Tested-by: jenkins
Added the chip definition for the Atmel AT91SAM4S4A. This chip is a 48-pin
package with 256k flash and 64k ram.
Change-Id: I8ada7d5735e31e0ce086f96f5906c7358464245c
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2254
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After SPI flash was written by the assembly language stub,
the last SPI command was not terminated by raising CS.
This left the SPI device in a hung state that prevented the
flash from being read by the M4 SPIFI controller, even after
the M4 was fully reset. To access the flash via SPIFI, it was
necessary to completely power cycle the board.
This fix adds the missing instructions to raise CS and
terminate the SPI command after the last byte. This allows
the M4 to be resumed or reset cleanly after flashing. The
SPIFI memory is now immediately accessable at address
0x1400 0000 after flashing is complete.
Change-Id: I4d5e03bded0fa00c430c2991f182dc18611d5f48
Signed-off-by: Anders <anders@openpuma.org>
Reviewed-on: http://openocd.zylin.com/2359
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds flash programming support for LPC1547/8/9 and LPC1517/8/9.
Tested on LPC1549(LPC1549 LPCXpresso Board with CMSIS-DAP firmware).
Change-Id: Ic95b4d62055bb9fdc2ca484696a38ccaf49ad951
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/2304
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Grigori G <greg@chown.ath.cx>
is_erased can take the value 0 (no), 1 (yes), or -1 (unknown).
Checks like (!is_erased) don't do the right thing if it's -1.
Change-Id: I10ba32c99494ca803e0a7a1ba56fdd78184b96bb
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2366
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the UICR is already empty, there's no reason to return an error
just because it can't be erased again. This happens, for example,
when flashing UICR from GDB after a "monitor nrf51 mass_erase".
Change-Id: Ia6d28c43189205fb5a7120b1c7312e45eb32edb7
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2363
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
nrf51_erase_page() checks for (sector->offset == NRF51_UICR_BASE) to
determine if the UICR should be erased. However, sector->offset for
the UICR bank is set to 0 in nrf51_probe, so this code is never hit.
Attempting to erase UICR ends up erasing the first flash sector.
Use bank->base instead to determine if UICR is being erased.
Change-Id: Ie5df0f9732f23662085ae2b713d64968cd801472
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2362
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The UICR region is actually 0x100 bytes in size. Besides making the
full region accessible, having the right value is important because
GDB rounds flash addresses to the nearest multiple of the block size
when determing which flash blocks to erase.
Change-Id: I416c391cbfc7be41a03a9b9c6e42326c87391f38
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-on: http://openocd.zylin.com/2361
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
added "Single Wire Output" and "Trace Memory Controller" peripheral
IDs to dap_rom_display(), which is invoked by the "dap info" command
Change-Id: Iea3201007bb98e6376fbb50be40a4a2e031b0a03
Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/2369
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The mass erase for STM32L was lack because the procedure is more complex
than the procedure for the STM32F4xx.
The reference manual RM0038 (L100 subfamily) page 79 is more accurate
than the reference manual for the STM32L0xx. On the L0, the mass-erase
erase also the EEPROM. This is a limit to mass erase on L0.
The mass erase procedure is a command of telnet interface.
Tested on Discovery L053 and Discovery L100.
Change-Id: I6a1d7a3669789aea89c59a006ab2d883f3d827ca
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2319
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add CPUTAPID for stm32 L0xx mcu devices. Using -expected-id to
add the new id with the id for L1xx devices. This for reduce the
duplicated code.
Change-Id: I48bd230884ecf38fa200c620b547bdf3b5f59132
Signed-off-by: Rémi PRUD'HOMME <prudhomme.remi@gmail.com>
Reviewed-on: http://openocd.zylin.com/2315
Tested-by: jenkins
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This should make protection work as expected on all stellaris
families, including the latest Tiva C Snowflake.
Run-time tested on TM4C123x (Blizzard).
Change-Id: Ia017edb119bec32382b08fc037b5bbc02dd9000c
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2267
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This introduces a new common function that allows auto-discovery of a
suitable USB interface based on class, subclass and protocol
matching. It claims the interface and returns the corresponding
endpoints number to the caller.
The need for this arised due to nRF51822 USB dongle which comes with
an "on-board Segger J-link debugger" having 3 interfaces, so the
current code can't work at all with it (in this particular case the
last interface needs to be choosen). This also removes special
handling of JLink-OB endpoint numbers as it's now possible to
autodetect them as well as the standard JLink endpoints.
Change-Id: I4d990a7a3b373efdd2949a394b32d855a168e138
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2327
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is still limited to pre-Snowflake parts and the first 64K of
flash.
Change-Id: I9ca872ada3d1a87dba6261464b2a72a15eda5ecf
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2264
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
TI's ICDI adapter supports some additional commands which a user might
want to run for debugging or other purposes, the most useful of them
being "debug unlock" that fully mass-erases the device and unprotects
the flash.
Change-Id: I26990e736094367f92106fa891e9bb8fb0382efb
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2263
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
