Some text file is missing newline at EOF.
Add it.
Change-Id: Ieebc790096f40961283c644642e56fde975e957f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5167
Tested-by: jenkins
The imx8mp-evk board has a FT4232H chip connected to the chip's JTAG
pins.
Switching between this on-board interface and the external ARM-10
connector is controlled by an GPIO which is behind an i2c expander
connected to the same FTDI chip.
Switching can be performed using the NXP bcu tool:
https://github.com/NXPmicro/bcu
Change-Id: Ic910515f76eaf09ea6d0f755b026fb09cf09ccfc
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5426
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.
Fix them with the same sed commands used for the other scripts:
sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)
Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Extend the driver to include the minimal functionality to support
the HLA model.
Due to the small change in the name (ST-LINK/V2 => STLINK-V3), fix
the existing names in the comments in udev rules.
Change-Id: Ied33e38063a6da81d9bf249ed195444d7cdf4f03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4717
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
New version of ST-Link/V2.1 without mass storage device.
From debug point of view, it is compatible with existing ST-Link/V2.1
It uses a new USB PID because the USB endpoints and interfaces are
different from usual ST-Link/V2.1
Add the new PID in the driver, in the tcl interface script and in the
udev configuration script.
Change-Id: Id2e1b5a5d0347c5d951a86a9cdb76be52cfd4ea3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4702
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for the XDS110 debug probe using the APIs in the
probe's firmware. Includes support for older versions of the
firmware (with reduced performance) and support for a newer
version that includes OpenOCD specific APIs. Tested on various
TI LauchPads including MSP432P4, MSP432E4, CC2650, CC2652, and
CC3220SF.
Updated to add better support for swd switch. Removed issues found with
clang static analysis.
Updated to add rules entry for the XDS110 probe and Tiva DFU mode (which
affects both XDS110 and ICDI probes).
Change-Id: Ib274143111a68e67e80003797c6a68e3e80976b2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/4322
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
When a user asks for blaster I, he or she should either get it, or get
an error, not blaster II driver.
Change-Id: Ibc7683676ce42773e2b14ea5ccb3d119d1e6acea
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4381
Tested-by: jenkins
This is a second try for this patch. I removed the queues from the
previous version. I made it compatible with SRST reset and added
support for those features that could be supported in raw binary
mode.
Change-Id: I96fc06abbea9873e98b414f34afd9043fd9c2a41
Signed-off-by: Mateusz Manowiecki <segmentation@fault.pl>
Reviewed-on: http://openocd.zylin.com/3960
Tested-by: jenkins
Reviewed-by: Eric Work <work.eric@gmail.com>
Reviewed-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Reviewed-by: Jacob Alexander <haata@kiibohd.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
30 MHz is not working reliably here
Change-Id: I38f5f8c7153fc64e313ee911b1629fb5f1114c39
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4242
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make all configs specify same JTAG and SWD GPIO numbers.
Change-Id: I65b09c1671c97f253f0aab88e511de7409d91e0a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3932
Tested-by: jenkins
* Disables the data output pin while SWD is reading, so that a simple FTDI
SWD interface can be made by connecting TCK to SWD_CLK and TDI+TDO directly
to SWDIO. Enabled by setting SWDIO_OE to 0.
Change-Id: I7d3b71cf3f4eea163cb320aff69ed95d219190bd
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
Reviewed-on: http://openocd.zylin.com/2274
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The Digilent SMT2 NC is nominally the connector-less version of the
SMT2. But neither the SMT2 configuration nor the HS3 configuration work
for on the Xilinx KCU105 board where the SMT2 NC is used.
Change-Id: Ieb27cbc6d8b0f9c64ef778e4e0c839acc85ec0ef
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4187
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Similar to the Sheevaplug fix inf95f8b70fbd0f7e9c91a2d9006b1abb2dd07ebf2
the OpenRD device has its JTAG interface on the first channel of the
ft2232, which is 0 for the new driver but was 1 for the old one. Correct
the config file appropriately. Also the device description was missing
the trailing " B" and thus not picking up the device correctly. Finally
add an adapter_khz setting in the OpenRD board configuration file - set
to 2MHz to match the Sheeva variant.
Confirmed as working thanks to Phil Hands providing me access to his
hardware to test on.
See also Debian Bug#793214; https://bugs.debian.org/793214
Change-Id: Ifacf53124eaa330bbbdf36dfa79e3256bf2a5201
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4254
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
- Tested on a real FT2232H MiniModule, so warning removed.
- Every pin initially set to high impedance except TCK, TDI,
TDO and TMS: Safest values given it's an evaluation board
and the rest of pins might be connected to something else.
- Reset is now initially de-asserted (it was asserted
which is not recommended).
- nRST pin choice is arbitrary so comment added (wondering
if it should be an "echo").
- "-oe" option added to NRST signal so it can be set as
high impedance (tri-stated).
Change-Id: I967ab0c7bbccf72dbf6d6d78b3180b74e016e0d6
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4185
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The migration from the old ft2232 driver to the new generic ftdi driver
ended up breaking support for the SheevaPlug device. The old driver
defaulted to channel 1, but numbered the channels 1 to 4. The new driver
starts at 0. The SheevaPlug JTAG is on interface A (interface B is the
serial console), so it should be using channel 0. Fix this. Confirmed
as working; serial console remains available and a new u-boot image can
be transferred across using the JTAG link.
See also Debian Bug#837989; https://bugs.debian.org/837989
Change-Id: I4ac2bfeb0d1e7e99d70fa47dc55f186e6af2c542
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4206
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.
Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7
Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.
Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
