This patch brings the calculation of the address ranges handled by
ttbr0 and ttbr1 registers in line with ARM DDI 0406C, Table B3-1
Change-Id: Ib807c4b1cb328a6f661e1a0898e744e60d3eccac
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3006
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
If ttbcr is changed after the debugger has examined a target for the
first time, address translations may fail. This problem does not show up
with Linux because it doesn't use ttbr1, but it shows with other OS that
use this feature. If the debugger connects to the target while it's in
u-boot, all address translations will fail after the OS has booted and
the target can not be debugged.
This patch reads the ttbcr in armv7a_mmu_translate_va() and compares it
a cached value. If a difference is detected, armv7a_read_ttbcr() is called
to re-parse the ttb configuration and update the cache.
Change-Id: I1c3adf53ea9d748a0e1e3091d9581e5c43ed64e8
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3005
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
New configuration for NXP LPC4370 which consists of a Cortex-M4
and two Cortex-M0 cores.
Change-Id: I9918e3ff33218a14a99e4bbab9dce2e7b45b4d96
Signed-off-by: Jim Norris <u17263@att.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2124
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
kinetis_write() with byte count not divisible by prog_section_chunk_bytes
computed wrong wc and therefore paded section chunk by some
random data instead of 0xff
Change-Id: Ic7c66d8a3ceacda9e611e98b9fbf943b8001774b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2994
Tested-by: jenkins
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Kx devices with FTFA flash need the watchdog disabled when programming.
I tried to keep overhead as small as possible and re-use registers that
were already inquired (e.g. sim_sdid).
Change-Id: Ibc29a26ec34102d78a6c3920dd16f63e134a8f6f
Signed-off-by: Thomas Schmid <thomas@rfranging.com>
Reviewed-on: http://openocd.zylin.com/2986
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This reverts commit 7d7a43fd36.
The change concerns the "Black" variant of the TI BeagleBone, while the
configuration file is for the original BeagleBone board, which actually
embeds a debug interface on the PCB.
Change-Id: I2232af210deb698f8b3c0a547f26cd0a0a8f89d0
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3094
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This makes it easier to relocate the install tree of OpenOCD from where
it was originally built (for example, if put onto a different machine),
without having to change scripts or add something to the command line
every time.
Change-Id: Ia5edf0eba166f7a999f267bd6a92402dab9b399e
Signed-off-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-on: http://openocd.zylin.com/3004
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add configs for Atheros ar2313 MIPS based WiSoC and
board based on this chip: La Fonera FON2200
Change-Id: Ibfdbfc9c2beca6cf436c9ee5e493b08bfb55ac85
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2839
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add configs for Atheros ar2313 MIPS based WiSoC and
board based on this chip: Netgear WP102
Change-Id: Id93957b5d5851a272f15be35f9f448a9ce6d8a08
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/2835
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The memory leak occurs when opening a file fails. It can be
reproduced by using the "flash verify_bank" command with a filename
that does not exist.
Change-Id: I60b7b545c18793d750ff75d08124fde3f0aa6f64
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2998
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If we work on smp system, the output of step command will depend
on Id of default target.
This patch adds additional information to help find what on which
core is happening.
Example of LOG after this patch.
imx6.cpu.1: target state: halted
^^^^^^^^^^
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x60000093 pc: 0x80076c0c
MMU: enabled, D-Cache: enabled, I-Cache: enabled
imx6.cpu.0: target state: halted
^^^^^^^^^^
target halted in ARM state due to debug-request, current mode: Supervisor
cpsr: 0x20000193 pc: 0x802ccb6c
MMU: enabled, D-Cache: enabled, I-Cache: enabled
Change-Id: I536a2cce33b5ab10af9de2a43b9960320c17729f
Signed-off-by: Oleksij Rempel <external.Oleksij.Rempel@de.bosch.com>
Reviewed-on: http://openocd.zylin.com/2691
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
A segmentation fault in cortex_m_endreset_event() is sometimes raised
with very broken target like Kinetis Kx with erased flash and active WDOG.
Debugging revealed that cortex_m->dwt_num_comp is 4 and
dwt_list is NULL at cortex_m:290
Change-Id: I229c59d6da13d816df513d1dbb19968e4b5951e2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2989
Reviewed-by: Thomas Schmid <thomas@rfranging.com>
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Since 2cbbe9a it was actually decreasing the configured work area size.
We could now do "set WORKAREASIZE 0x2000" before sourcing lpc4350.cfg,
but there seems no point in doing so. Simply drop the configuration here.
Change-Id: I25b9dbbc007ba652b66099832198b7c329929858
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3086
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Memory for the symbol table was allocated by malloc but not initialized other
than with the symbol name. Therefore `address` and `optional` members were
having arbitrary values leading to every symbol being optional most of the
time which messes up RTOS auto-detection. Memory will now be zero-initialized
as in other RTOS implementations.
Change-Id: I6c6e31ec1ef7e043061adf8c695b2139620e005d
Signed-off-by: Daniel Krebs <github@daniel-krebs.net>
Reviewed-on: http://openocd.zylin.com/3017
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Default to lpc8xx as before, but allow setting the actual CHIPNAME.
Change-Id: I5a48fa75c640440a0d4c3f2858653e94bed846d2
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3084
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to "man 2 poll" the correct header to include is poll.h, not
sys/poll.h. Reported by a build against musl.
Change-Id: I5298b49dc947d1a368e423104c0c0c7b9bdd1a10
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/2947
Tested-by: jenkins
