Extend the driver to include the minimal functionality to support
the HLA model.
Due to the small change in the name (ST-LINK/V2 => STLINK-V3), fix
the existing names in the comments in udev rules.
Change-Id: Ied33e38063a6da81d9bf249ed195444d7cdf4f03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4717
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
The ST-LINK/V2.1 embedded in the new nucleo boards for STM8 does
not follow the normal versioning rules, and puts mass-storage and
swim version in the field normally used respectively for jtag and
mass-storage version.
Apply the check suggested by STMicroelectronics to discriminate
the two cases and print the correct version.
Change-Id: I0dd1da11013be3f1e56084489e28cfba98bb07af
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4716
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Starting from stlink V2J15 the API
STLINK_DEBUG_APIV2_GETLASTRWSTATUS
is obsoleted and replaced by the new API
STLINK_DEBUG_APIV2_GETLASTRWSTATUS2.
Manage the two cases to be prepared for an eventual future
removal of the obsolete API.
Change-Id: Ic4498a652865b2eb6148825138c2f6855a06ba47
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4714
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Until version J14 the behaviour of ST-Link was to send a reset
pulse to the target when the debug connection is started in JTAG
mode. No reset pulse is sent, instead, in SWD mode.
Version J15 introduces a new parameter to avoid the reset pulse in
JTAG mode, aligning the behaviour with SWD.
This reset from the ST-Link, if propagated to the target, prevents
attaching a running target.
Actually this reset pulse is very short (few microsecond) and can
be easily filtered out by an on-board capacitor, usually present
on the reset wire (mainly to filter the bounces of the reset
button). Moreover, most of the use cases for ST-Link are with SWD
(not with JTAG) and this has probably further masked this JTAG
specific behaviour.
OpenOCD can tolerate it but requires the flag "connect_assert_srst"
to the command "reset_config", but the flag is not present in any
configurations in folder tcl. This enforces the guess it was not
noticed due to on-board capacitors or missing connection of reset
pin or ST-Link only used in SWD; so it's safe applying this patch.
Change the default behaviour to avoid reset in JTAG at connection.
There is no need to manage the ST-Link version here, since every
parameter that is not recognized by older ST-Link is treated as
"connect in JTAG with reset pulse", keeping backward compatibility.
Change-Id: Idc97a1457279e3970fd0839cadbff22d9b0302d4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4713
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The API version is hardcoded in the STLINK device and depends on
the specific firmware version. There is no way to switch between
different API. Thus, it make no sense to keep in two separate
variables the current and the max API supported because they are
always equal to "the only" API supported by the specific STLINK.
Collapse h->version.jtag_api_max and h->jtag_api in a single
variable h->version.jtag_api
Remove an extra print of api version; this is already advertised
while printing the STLINK version.
Change-Id: I0519694a34748e5a0aa330932c1256080a6d5f20
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4712
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fix the condition for ST-Link/V1; it does not support trace.
Trace is added on ST-Link/V2 and ST-Link/V2.1 only.
Change-Id: I17416edd05a2c8ece605560b7533edac4f982cfc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4707
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The number of stlink firmware version is growing, each carrying new
features. Today's code has several check distributed here and there
and it's already hard to track them and verify the correctness.
The introduction of STLINK-V3 will make the situation much worst,
and the code much less readable.
Add a "flags" bitmask in the struct stlink_usb_version to allow
setting individual bits for each feature available or for specific
quirks and workarounds.
This patch does not implement setting nor testing "flags"; it would
be introduced in following patches, one bit at a time.
Change-Id: I09d78202646a6c8330731f8aa96dc9d295fa5655
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4706
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The old ST-Link/V1 can either run an obsolete firmware with API_V1 or
a more recent firmware (from V1J11 to last V1J13) with API_V2.
SWD is only provided by the latter API.
Return error is SWD is selected on adapters that does not support it.
Change-Id: Iac4ba54d191ba80fb445a7cd3d8c2621dc7a4846
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4705
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Recent stlink version V2J26 introduces support for 16 bit memory
read/write.
Add the new API and modify the wrappers stlink_usb_{read|write}_mem
For older version of stlink keep the same behavior as in current
code.
While there, fix some minor typo in comments inside the wrappers.
This fixes ticket #204 ("st-link can't flash stm32f2x based flash
without target algorithms").
Change-Id: Id7d404e588f10a4b0f8a93d7ca44cef8e4c49b4f
Author: Laurent LEMELE <laurent.lemele@st.com>
Rebased-by: Antonio Borneo <borneo.antonio@gmail.com>
Ticket: https://sourceforge.net/p/openocd/tickets/204/
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4704
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
ST-Link uses two separate API for setting the interface speed in SWD
and JTAG.
Add the missing API for JTAG and run the proper API depending on the
selected mode.
Change-Id: I71e955e23c1d82c2ea1c8bfade7612c5a0377a74
Author: Laurent LEMELE <laurent.lemele@st.com>
Rebased-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4703
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
New version of ST-Link/V2.1 without mass storage device.
From debug point of view, it is compatible with existing ST-Link/V2.1
It uses a new USB PID because the USB endpoints and interfaces are
different from usual ST-Link/V2.1
Add the new PID in the driver, in the tcl interface script and in the
udev configuration script.
Change-Id: Id2e1b5a5d0347c5d951a86a9cdb76be52cfd4ea3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4702
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The original code was written for and tested on little-endian
host only.
Rewrite it to be independent by host endianess.
Not tested on real HW; I don't own anymore a SPEAr device.
Change-Id: I2f427a804693f56cb9dea4936c525eb814c48c28
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4778
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds support for reading halfword values from memory. This
command compliments existing support for writing halfwords (mwh).
Change-Id: I8ec628e65c05a7f00aa57e3af0f228eb8bd4d14e
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4781
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
FT232R: introducing configurable parameters for pinout,
initial buffer size, state of RS232 signals at exit with
option to reattach kernel driver. All this was hardcoded before.
New parameters are documented in "openocd.texi" file.
Allows hopfully self-explainable and user-friendly adaptation to
various pinouts and similar chips like FT230X and FT231X.
Change-Id: Ib807f2ea3d4c1a164d351d65aeacd1978318d217
Signed-off-by: EMARD <vordah@gmail.com>
Reviewed-on: http://openocd.zylin.com/4681
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Some flash drivers had a dummy method for erase_check.
Use default_flash_blank_check() instead if possible.
Change-Id: Iddfeff45ce477007328d061fcb5c553d93c3be98
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4766
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
read_cmd, qread_cmd, pprog_cmd added as some recent high densities devices
use variants for 4-byte addressing.
Some new flash and FRAM device ids added. FRAMs don't have write pages nor
erase commands or sector sizes. The corresponding entries are marked as
"not used" (i. e. zero). Checks in existing SPI flash drivers added to
handle these cases gracefully.
Change-Id: I5104bce7c815ac22f98bc32c1bb6db66b984404a
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4773
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This increases performance drematically for local connections, which is the
most likely arrangement for a VPI connection.
Change-Id: Id15b29ae663f5d8100b2175357649bd03d05b7c8
Signed-off-by: Darius Rad <darius@bluespec.com>
Reviewed-on: http://openocd.zylin.com/4549
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make flash_driver methods protect() and protect_check()
optional.
Remove dummy definitions of these methods from the drivers
which do not implement protection handling.
Some drivers did not define protect method. It raised segfault
before this change and now it is handled properly.
Lot of drivers returned ERROR_OK from dummy protect()
- now flash_driver_protect() returns an error if not handled by the driver.
Change-Id: I2d4a0da316bf03c6379791b1b1c6198fbf22e66c
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4765
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
