Save and display the address of the instruction which triggered the
watchpoint. Because of pipelining, that's well behind the PC value
when debug entry completes. (Example in a subroutine that had been
returned from...)
Remove unused A8 stuff, mostly watchpoint hooks from the header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Except for USR/SYS mode, the labels for the shadowed SP and LR
registers were reversed. LR is r14; SP is r13. Fix.
This would not affect GDB users; GDB references are positional.
Only folk working directly with OpenOCD register values would
have noticed this bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Actually this should handle both breakpoints and watchpoints ... but
the DPM framework only handles watchpoints for now. Works on Beagle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This is a NOP unless the underlying core exposes two new methods, and
neither of the two cores using this (ARM11xx, Cortex-A8) do so yet.
This patch only updates those cores so they pass a flag saying whether
or not to update breakpoint and watchpoint status before resuming; and
removing some now-needless anti-segfault code from ARM11. Cortex-A8
didn't have that code ... yes, it segfaulted when setting watchpoints.
NOTE: this uses a slightly different strategy for setting/clearing
breakpoints than the ARM7/ARM9/etc code uses. It leaves them alone
unless it's *got* to change something, to speed halt/resume cycles
(including single stepping).
ALSO NOTE: this under-delivers for Cortex-A8, where regions with size
up to 2 GBytes can be watched ... it handles watchpoints which ARM11 can
also handle (size 1/2/4 bytes). Should get fixed later.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
In embedded hosts, the Jim interpreter can come from the
existing context rather than be created by OpenOCD.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
We don't need this code, now that the DPM code handles it.
Neither do we need the ARMv7-A CP15 operations; remove their
remnants too. And disable a mostly-needless diagnostic.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Instead of having separate ARM11 and Cortex-A8 implementations of
this code, have one shared implementation which just builds on the
existing "run instruction via R0" support.
This enables followup patches to remove that now-unused code from
those two drivers. (Patches to move the "mrc" and "mcr" code into
"struct arm" are due too ... MIPS and other cores do not support
those ARM-specific concepts.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Switch "mrc" and "mcr" commands to be toplevel ARM operations,
as they should initially have been.
Correct the usage message for both commands: it matches ARM
documentation (as one wants!) instead of reordering them to
match the funky mrc() and mcr() method usage (sigh).
For Cortex-A8: restore a line that got accidentally dropped,
so the secure monitor mode shadow registers will show again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The ARMv7-A code uses read_cp15() to access fault registers.
Instead, use DPM operations directly, passing in the relevant
MRC instructions.
This eliminates per-operation overhead (though it'll be hard
to observe, this is uncommon) and helps eliminate read_cp15().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
There were two chunks of Cortex-A8 code which called the
ARMv7-A CP15 operations; get rid of them, helping prepare
to remove those methods completely:
- post_debug_entry() can use the mrc() method to read
its two registers.
- write_memory() can use dpm->instr_write_data_r0() to
flush the ICache and DCache ... doing it this way is
actually faster since it reduces per-write overhead.
Note that the mrc() method parameters are re-ordered with
respect to the ARM instruction documentation, so that part
can be confusing.
Cleaned up the layout and comments in those areas a bit.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
There is no particular reason to invoke jtag_interface_quit()
on the atexit() handler, it just makes the code more obtuse
and stops other legitimate usage of atexit().
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Ensures that the correct information gets displayed, depending on the
mode of the command being denied. Fixes misreporting all commands as
needing to run "before 'init'".
Clean up two aspects to this routine: bad naming, since it
doesn't restore the context, just the banked registers; and
excess indentation for the bulk of the code.
Also make some of its call sites stash the function's return
code; someday they should use it for error checking.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This "loop over all registers" routine shared the same mess as
full_context() in terms of dozens of needless number_to_mode()
calls. Fix that, and comments, with related cleanup.
The misnamed xscale_restore_context() had a related bug. It
was restoring the *WRONG REGISTERS* ... always from whatever
the current mode was, instead of using the copy from whichever
register bank it was trying to restore. (But it marked the
intended register as having been restored...) Fixed that.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Finish removing references to the 'interp' global variable from the
command module, encapsulating all reference via command_context.
Eliminates use of the global entirely, so it can be removed. Hurrah!
Adds a log_capture_state structure to pass to the log capture
callback used by the command module. Ensures that the capture occurs
in the proper context.
