Prepare to support multiple cortex-m cores on one DAP. Uses mem_ap_sel_*
functions and removes mem_ap_* functions. Adds a new debug_ap
parameter to the cortex_m (currently set to zero as in existing code).
Change-Id: I6926029d1e7bf44a42d453d1aff349bda824ba72
Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2983
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is a TODO in the src/target/arm_adi_v5.h for MEM-AP registers.
Some new registers are introduced in ADIv5.2 specification.
MEM_AP_REG_MGT (0x20) // Memory Barrier Transfer register
MEM_AP_REG_TAR64 (0x08) // Bits[63:32] of Transfer Address
MEM_AP_REG_BASE64 (0xF0) // Bits[63:32] of Debug Base Address
Refer to
7.5 MEM-AP register summary in
IHI0031C: ARM Debug Interface Architecture Specification ADIv5.0 to ADIv5.2
Change-Id: I3bc4296a04c35f5c64f851e5865d3099922613fa
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2904
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Problem
No matter what target->coreid is, it always shows
Detected core 0 dbgbase: ...
In dap_lookup_cs_component(), it decreases the core index value to zero
in order to find the desired core.
The reference to coreidx is necessary considering "a device which has nested
ROM tables, with each core described in its own table." (by Paul Fertser).
Change-Id: I9b56d45d6edf6639e748a625ab27787f8e5a5776
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2902
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
They are only used to initialize the flash bank sectors and never modified.
Explicitly specify the array length while at it.
Cleanup before adding XMC4800 support.
Change-Id: I2985b9a9946b67798dbfd47d8b219d93a7ffc3da
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3131
Tested-by: jenkins
Reviewed-by: Jeff Ciesielski <jeffciesielski@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
cortex_a_read_apb_ab_memory_fast() uses the wrong order of ITR and DSCR
writes when setting up the transfer. ARM DDI0406C says in C8.2 regarding
"Fast mode" operation to first switch to fast mode and then latch the
instruction in ITR. Current implementation first wrote ITR, causing
the instruction to be executed immediately, then switched to fast mode
without an instruction latched. Repeated reading of DTRTX didn't
execute LDC and thus replicated its current content into the whole buffer.
This patch uses the following, revised algorithm:
1) switch to non-blocking mode and issue the LDC for the first word
2) if more than one word is to be read:
- switch to fast mode
- latch the LDC instruction into ITR (it is _not_ executed)
- issue (count-1) reads of DTRTX register, each read returns the current
content of DTRTX and re-issues the latched instruction
-> now the second-to-last word is in the buffer and the LDC for the last
word has been issued.
3) wait for the last instruction to complete
4) switch back to non-blocking mode
5) Read DTRTX for the last (or: only) word and put it into the buffer
Change-Id: I44f5c585962ffa5af257c3d5a2a802c122b6b1e4
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3122
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When accessing memory through the ARM core, privilege levels and mmu
access permissions observed. Thus it depends on the current mode of the
ARM core whether an access is possible or not. the ARM in USR mode can
not access memory mapped to a higher privilege level. This means, if the
ARM core is halted while executing at PL0, the debugger would be
prevented from setting a breakpoint at an address with a higher privilege
level, e.g. in the OS kernel. This is not desirable.
cortex_a_check_address() tried to work around this by predicting if an
access would fail and switched the ARM core to SVC mode. However, the
prediction was based on hardcoded address ranges and only worked for
Linux and a 3G/1G user/kernel space split.
This patch changes the policy to always switch to SVC mode for memory
accesses. It introduces two functions cortex_a_prep_memaccess() and
cortex_a_post_memaccess() which bracket memory reads and writes. These
function encapsulate all actions necessary for preparation and cleanup.
Change-Id: I4ccdb5fd17eadeb2b66ae28caaf0ccd2d014eaa9
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3119
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
when disabling the mmu to access physical addresses, normally the d-cache
must be disabled as well. Disabling the d-cache also requires a full
clean&invalidate. However, since all memory writes are treated as write-
through no-allocate and memory reads do not allocate cache lines,
effectively the d-cache state does not change at all. We can therefore
save the the d-cache disabling and flushing.
This patch also simplifies the function a bit.
Change-Id: Ia17c56a28f432156429cd4596107e3652b788e63
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3114
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
for minimal impact on the hardware state, force all memory accesses to
bypass the caches and tlbs. This may actually be the default, but ARM
recommends in DDI0406C to set proper default values on debug init.
Change-Id: If5ac097b6ee725c047b1e86c2f90eabe16b98c7b
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3079
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
Other cache functions use an updated pattern for the address range loop.
Bring dcache clean and flush functions in line.
Change-Id: Iccb4a05c49054471033a3403363110cb08245d5b
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3035
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Call armv7a_l1_d_cache_flush_virt() before writing the breakpoint,
to make sure the d-cache is clean and invalid at the breakpoint
location down to PoC.
Call armv7a_l1_d_cache_inval_virt() after writing the breakpoint
again, so that d-cache will pick up the modified code.
Call armv7a_l1_i_cache_inval_virt() after writing the breakpoint
to memory to make the change visible to the CPU.
Change-Id: I24fc27058d99cb00d7f6002ccb623cab66b0d234
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3033
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
D-Cache invalidate is a dangerous operation. It will only work correctly
if full cache lines are invalidated. When partial cache lines are
invalidated, i.e. the target address range does not start and end
at a cache line boundary, cpu data writes outside of the target range
will be dropped. This patch adds special treatment for partial cache
lines by doing a clean & invalidate on the partial lines before
invalidating the rest of the range.
Change-Id: I64099ddb058638e990a7eb0ee911b9cc8f6f8901
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3034
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The following changes are implemented:
- Clean&Invalidate the VA range to PoC *before* the write takes place
- Remove SMP handling since DCCIMVA instruction already maintains SMP
coherence.
- Remove separate Invalidate step
Change-Id: I19fd3cc226d8ecf2937276fc63258b6a26e369a7
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3027
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This patch adds a function for cleaning & invalidating a virtual
address range from the architecture caches down to the point of
coherence.
Change-Id: I4061ab023a3797fabc967f3a34498034841d52c6
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3026
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
There's only one function left that handles cache info display,
no need any more for a function pointer and runtime initialization.
Change-Id: I90b09577f81607917b11f0ab5600a0e2dce223e2
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3025
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
ARMv7 architecture allows up to 7 cache levels that are architecturally
visible, as opposed to "system caches", which are outside of the domain
defined by ARMv7 and require separate management. This patch enables
detection and identification of caches at all levels. It also implements
a new "flush-all" function that cleans & invalidates all cache levels to
the "Point of Coherence".
Change-Id: Ib77115d6044d39845907941c6f031e208f6e0aa5
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3024
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: jenkins
This patch is on the path to unified handlers for both inner and
outer caches. It removes the special overrides installed when
an outer cache is configured.
Change-Id: I747f2762c6c8c76c700341cbf6cf500ff2a51476
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3022
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The outer cache is not necessarily at L2 in a system. Rename functions
to make that clear.
Change-Id: Ia636a4844f50634f2bdf5cdce285febc1a47c11f
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3020
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch introduces, new command set and handlers for l1 and l2x caches.
Patch set 10 folded the following changes into this one:
Ib1a2a1fc1b929dc49532ac13a78e8eb796ab4415
If8d87a03281d0f4ad402909998e7834eb4837e79
I0749f129fa74e04f4e9c20d143a744f09ef750d8
Change-Id: I849f4d1f20610087885eeddefa81d976f77cf199
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/2800
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
