STM32L ref manual (RM00038 Rev5) states the SW-DP id should be 0x4ba00477.
The correct value from silicon is 0x2ba01477 - the typo has been confirmed by ST.
Change-Id: Ie35a1f13dc5dedc1b148fb219c6974bfa48b537c
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/441
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This enables the user to override the transport used for st-link.
If JTAG is selected it will also change the default id used to the JTAG id
rather than the SW-DP id.
Change-Id: I4fe352e4932e2f4ec278168e99ba2d2d50fd850a
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/443
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This adds init_board procedure that behaves exactly the same as
init_targets - it can be overriden by "next level" scripts. This
procedure is executed after init_targets, allowing common stuff (jtag
chain, memory, flash, ...) to be configured in target script (via
init_target) and leaving rest (like additional memory, reset
configuration, reset-init handlers, ...) to be done in init_board.
This makes init_targets scheme more complete and easier to use - current
board scripts will not need new init_targets, because everything can be
"packed" in init_boards. Moreover it solves the problem of variables
being set in init_targets (executed after init), which were not
accessible by "linear" scripts (parsed before init). All that has to be
done is to enclose all code in board config file in init_board
procedure.
Change-Id: I0736b1ff9873a687966407d62b58ccf29a8e597b
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/427
Reviewed-by: Chris Morgan <chmorgan@gmail.com>
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This issue was caused by uncrustify not correctly converting the doxygen
comments.
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Change-Id: Ie6dc3b057a08603b670cb27312e5f0d989426e6c
Reviewed-on: http://openocd.zylin.com/431
Tested-by: jenkins
These checks are specific to linux kernel.
Change-Id: Ia9b837b5609922a897822f1d55f96f04c0f1f838
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/424
Tested-by: jenkins
We may enable this again - but at the moment is causing extra issues
with reformatting the codebase.
Change-Id: I5a2aaaa32ad784e011dff3079ff45501452c1819
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/414
We may enable this again - but at the moment is causing extra issues
with reformatting the codebase.
Change-Id: Ic64310a20605a0ef3206caa15c8e6c8ee655bfda
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/413
Tested-by: jenkins
