Rather than failing if the flash size reg cannot be read lets assume
we have the max flash size fitted.
It is quite common on early ST silicon to not correct support this register.
Change-Id: Ife058d60ae0027faad2c929ebd5b7fe2ef27234d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/743
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Revision X is not mentioned in the latest RM0038 rev5, however it has been
confirmed correct by ST using ST-LINK Utilty.
Change-Id: I65210e512ea25818a1d0d3b223502ebd7535b29d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/742
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
- Moved variant-independent code to lpc17xx.cfg, which will be included from
lpc17??.cfg files automatically.
- lpc1768.cfg filled with variant-dependent code.
Change-Id: I7dabe6ed7da7be640ed38c13aaaa096b8796d9a0
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/675
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
FT232H chips are new highspeed devices from FTDI. Basically these are a half of FT2232H (or a quarter of FT4232H), so only one channel which can be used as OpenOCD
interface. The chips are supported by libftdi 0.20 or later and by ftd2xx 2.08.12 or later.
Change-Id: Ic9a2c279167c3419a24f0d6befacbb83c4ffeb25
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/736
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es>
It's unnecessary and prevents reusing this function to fix
option byte writes.
Also try to disable flash writing after an error.
Change-Id: Ib5a7b768a1523e6b8da1555126fef4c1e60ab083
Signed-off-by: Szymon Modzelewski <szmodzelewski@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/479
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The existing code tests the current debug_level for validity, allowing
the user to set it too high and never change it after that. The new
behaviour is to test the debug_level that the user has requested.
Change-Id: I85726a2e606c8d137e9b1cfe76fee865084844b1
Signed-off-by: Alan Bowman <alan.michael.bowman@gmail.com>
Reviewed-on: http://openocd.zylin.com/764
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Based on ft2232.c but uses the MPSSE layer for low-level access, greatly
simplifying the JTAG logic. Remove all libftdi/FTD2XX code and all layout
specific code. Layout specifications are instead handled in Tcl.
Use a signal abstraction to enable Tcl configuration files to define
outputs for one or several FTDI GPIO. These outputs can then be
controlled using the ftdi_set_signal command. Special signal names are
reserved for nTRST, nSRST and LED (for blink) so that they, if defined,
will be used for their customary purpose.
Depending on the type of buffer attached to the FTDI GPIO, the outputs
have to be controlled differently. In order to support tristateable
signals such as nSRST, both a data GPIO and an output-enable GPIO can be
specified for each signal. The following output buffer configurations are
supported:
* Push-pull with one FTDI output as (non-)inverted data line
* Open drain with one FTDI output as (non-)inverted output-enable
* Tristate with one FTDI output as (non-)inverted data line and another
FTDI output as (non-)inverted output-enable
* Unbuffered, using the FTDI GPIO as a tristate output directly by
switching data and direction as necessary
The data and output-enables are specified as 16-bit bitmasks,
corresponding to the concatenation of the high and low FTDI GPIO
registers. To specify an unbuffered output, use the same bitmask
for both data and output-enable.
The adapter configuration file must also specify default values for the
FTDI data and direction GPIO registers, and the channel being used (if
different from 0).
Change-Id: I287a41d4c696cf5fc74eb10d5e63578b0dc7f826
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/452
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This is a higher-level libftdi replacement for use when implementing
protocol drivers for FT2232, FT2232H or FT4232H. It takes care of device
open/close and, unlike libftdi, also MPSSE command abstraction, command
queueing, buffer handling and return data parsing.
The FTDI device is accessed through libusb-1.0 in asynchronous mode.
Change-Id: I051adb574dcc39f8ca9cd7f6dbe6ae4aeea5f4c8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/451
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
The ADIv5 spec guarentees that tar_autoincr_block will be 10bits.
Make this the default for Cortex-M family until we detect a Cortex-M3/M4,
we then change autoincrement to 12bits.
Change-Id: Ie8c89134aa036879bdd8a3c312cee9715dbc6913
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/730
Tested-by: jenkins
Reviewed-by: simon qian <simonqian.openocd@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
openocd -f board/sheevaplug.cfg -c init -c exit
the calling shell will believe that openocd exited with an error due to exitval will be non-zero
This is not tested against incomming telnet
Change-Id: I63d15715a7b46f39a7de261a45039f8c3cad7a98
Signed-off-by: Stian Skjelstad <stian@nixia.no>
Reviewed-on: http://openocd.zylin.com/470
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
Reviewed-by: Mathias Küster <kesmtp@freenet.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
jim_target_md is supposed to print out results with command_print in
hexdump format. It was using command_print which appends a newline character
aftre every invocation. Using command_print_sameline instead
Change-Id: Iaff03021acc38d54b5a082cb58b82aa4449c0715
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/669
Tested-by: jenkins
Reviewed-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
- Added a few lines of comment before the function explaining the usage and the
output generated by the command
- Added a few lines of comment in the body explaining what is happening to improve
code readability
- Renamed a few variables to improve readability:
* a -> addr
* b -> dwidth
* c -> count
- Added a new variable, named byte to contain the number of bytes to read, instead
of overwriting the count parameter, to avoid confusion between the two values.
Change-Id: I5828ec0f5aadaa39becec7b84f198756bb2c3d41
Signed-off-by: Vandra Akos <axos88@gmail.com>
Reviewed-on: http://openocd.zylin.com/665
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Interface drivers regularly need to keep track of where each part of a long
read buffer should be copied, once that data arrives. Both source and
destination are often at an arbitrary bit offset.
This queued bit-level copy can help with that, by allowing the driver to
perform postponed reads from the receive buffer already when building the
transmit buffer, and have those reads executed at a later time when data is
available.
For simplicity, it uses the linked list implementation list.h imported from
the Linux kernel.
Change-Id: I06862a0a6f057cbbcacfb021f17a795195faded2
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/450
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Peter Stuge <peter@stuge.se>
New flash description for ATSAM3SD8C used on SAM3S-EK2 development boards. Name used
is "at91sam3sd8c" and chipid is 0x29ab0a60. Mirrors description of other similar parts.
Change-Id: I7fc4b82e7969451645ab067223663f08b76d866b
Signed-off-by: Mike Crowe <mpcrowe@gmail.com>
Reviewed-on: http://openocd.zylin.com/684
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
jtag_interface.transports field was left uninitialized, which triggers warning message
on program startup.
Although hardware natively supports SWD interface, no software support
currently present, so the value choosen to be <jtag_only>.
Change-Id: I2da41790b1850950af416cec4362d5b7bf927b2b
Signed-off-by: Alexander Osipenko <sipych@gmail.com>
Reviewed-on: http://openocd.zylin.com/670
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
