ocd_ prefix is used internally in OpenOCD as a kludge more
or less to deal with the two kinds of commands that OpenOCD
has.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone. I noticed some incorrect information in the user manual
regarding how the vector table is handled on the xscale, so for your
consideration, here's a short patch that corrects it, and adds a
little more detail I thought might be helpful.
The documentation states that OpenOCD does not attempt to synchronize
the vector tables in memory with those stored in the "mini instruction
cache". In fact, on each resume it does copy from memory to the cache
all entries in the high and low tables that were not previously
defined using the 'xscale vector_table' command. (In
src/target/xscale.c, see xscale_update_vectors(), which is invoked by
xscale_resume().) I take advantage of this during Linux boot-up. The
extra detail describes in general terms how I do this.
Corrections, comments are of course gratefully received.
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Make it scriptable, so code can be conditionalized based on
what transport is in use for the session.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds the guts of a transport framework with initialization,
which should work with current JTAG-only configurations (tested
with FT2232).
Each debug adapter can declare the transports it supports, and
exactly one transport is initialized. (with its commands) in
any given OpenOCD session.
* Define a new "struct transport with init hooks and a few
"transport" subcommands to support it:
"list" ... list the transports configured (just "jtag" for now)
"select" ... makes the debug session use that transport
"init" ... initializes the selected transport (internal)
* "interface_transports" ... declares transports the current interface
can support. (Some will do this from C code instead, when there are
no hardware versioning (or other) issues to prevent it.
Plus some FT2232 tweaks, including a few to streamline upcoming
support for an SWD transport (initially for Luminary adapters).
Eventually src/jtag should probably become src/transport, moving
jtag-specific stuff to transport/jtag.
Signed-off-by: David Brownell <db@helium.(none)>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
1. fix some errors in jtag.txt(in my personal opinion, please review).
2. remove a broken link
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
There are a million reasons why cached protection state might
be stale: power cycling of target, reset, code executing on
the target, etc.
The "flash protect_check" command is now gone. This is *always*
executed when running a "flash info".
As a bonus for more a more robust approach, lots of code could
be deleted.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Flash probing must succeed for e.g. gdb load and automatic
hardware/software breakpoints to work.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Clean up the jtag/tcl.c file, which was one of the biggest and
messiest ones in that directory. Do it by splitting out all the
generic adapter commands to a separate "adapter.c" file (leaving
the "tcl.c" file holding only JTAG utilities).
Also rename the little-used "jtag interface" to "adapter_name", which
should have been at least re-categorized earlier (it's not jtag-only).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The mips_m4k_assert_reset has now been restructured
so the variant ejtag_srst is not required anymore.
The ejtag software reset will be used if the target does not
have srst connected.
Remove ejtag_srst from docs.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Globally rename "jtag_nsrst_assert_width" as "adapter_nsrst_assert_width",
and move it out of the "jtag" command group ... it needs to be used with
non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Globally rename "jtag_nsrst_delay" as "adapter_nsrst_delay", and move it
out of the "jtag" command group ... it needs to be used with non-JTAG
transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
