This adds a set of helper functions with the aim to make it possible
to flash mass-market devices without RTFMing altogether (i.e. to
obsolete GPL-violating proprietary tjtag and other similar software).
Real-life tested on an RT-N16 and WRT54GL.
Change-Id: I197a9b28a5f386803f081057c4b4ebf2f9c447b1
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1850
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds the bcm47xx config with the special undocumented trick to
put it into standard EJTAG mode from the mystic "LV mode".
The RAM setup is not done as it would require considerable efforts
without much practical gain.
The only issue I noticed so far is that "reset" doesn't actually reset
the chip.
Unfortunately, it's unclear how to make it work properly with SRST as
OpenOCD asserts it in MIPS-specific code so the device will enter LV
mode again but the LV tap is already disabled by that time, so it's
not possible to send the magic command again.
Anyway, this config is more than enough to "recover" any RT-N16
provided the hardware is not damaged.
Change-Id: I0894e339763e6d20d1c93341c597382b479d039b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1849
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
To be consistent with gdb_port and telnet_port, allow tcl_port
to be run to display the configured port number, while still
not allowing the user to change it after configuration.
Change-Id: Ibe6aedb3bd447f2985e42dd8246358481a047dd6
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1857
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
* openocd.berlios.de -> openocd.sourceforge.net
* Update link to AM/DM37x Technical Reference Manual (ver R)
* "ICEpick" is properly spelled "ICEPick" according to TI
Change-Id: Ie04458e82c97ef766ec03bd9b9f27edadf5d1cb2
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1856
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is not in the Intel hex file format specification but
some hex files may include comments (i.e. Altera USB-Blaster II
firmware) starting with '#'.
This patch makes image_ihex_buffer_complete_inner to skip
comment lines.
Change-Id: Id1f57d84d75da45e592f1c72b2b8c29193bc14e3
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1842
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
S25FL256S device tested on mbest LPC4357 EVM, S25S128S untested but
from the same data sheet.
Change-Id: Idf58416aab08671fe29d22c3c34c2118b25a9d45
Signed-off-by: Steve Moorby <steve.moorby60@gmail.com>
Reviewed-on: http://openocd.zylin.com/1844
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Try to detect the flash parameters based on the MCU SDID register. The hope
is that this works for K and KL series MCUs but it has only been tested on
a K21. YMMV.
Change-Id: Idfe71383a449065267f393b09ee3c3b24ac6a803
Signed-off-by: Per Ekman <pekenator@gmail.com>
Reviewed-on: http://openocd.zylin.com/1823
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On all platforms, search for scripts in
$HOME/.openocd
${run_prefix}${pkgdatadir}/site
${run_prefix}${pkgdatadir}/scripts
On Windows, set run_prefix to the runtime path of the executable, minus
${bindir}. This is to enable the install dir to be moved anywhere, as long
as the structure of the install dir is kept intact. On all other platforms,
run_prefix is empty.
The script paths can now be adjusted on Windows builds the normal way; by
overriding pkgdatadir at build time. For example, to create a Windows
package layout of
bin/openocd.exe
scripts/interface/...
scripts/target/...
you can do
configure --prefix= --enable-... and then
make pkgdatadir= DESTDIR=/some/path clean all install
Also, remove the unused PKGLIBDIR define.
Change-Id: If2c8228fc80c598d763efad21c5f51695ff9b6cf
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1796
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The set command was missing the $ prefix on the SJC_TAPID variable
and so would fail if SJC_TAPID was set
Change-Id: Ib9af58f5188bd8a2bc3f888309f203d624476c27
Signed-off-by: Alex Murray <alex.murray@cohdawireless.com>
Reviewed-on: http://openocd.zylin.com/1811
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch remove the hardcoded libraries. Also a check for
libftdi1 installations was added. This check fix an issue
with gentoo and maybe other systems.
Change-Id: Ieff9ec4d66ee0f3e6b22261a10e4cab9f26b6b51
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1759
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Based on Nemuisan Tokusei's. Untested, but original config was reported
to work ok.
Change-Id: Ic991dce55bfca266880081fe2bbd9e6e263b0fc0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1803
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
all other at91 cfg files already has this fix.
It also fix "No flash at address 0x...." error when JTAG chain consist of
more than one at91sam7sx cores during attempt to flash other than first mcu
in chain.
Change-Id: I7785d9103d0fc494b6a823e2c73f850373ffe112
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/1812
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
STM32F42xxx & STM32F43xxx series boudary scan TAP-ID are differ from
STM32F405xx/07xx & STM32F415xx/17xx.
And Section number was also fixed for RM0090 rev5.
Tested on a STM32F427IIT6 and STM32F429ZIT6.
Change-Id: Ie9c54c55b97b9c396ace752d94ea2ad916cc8479
Signed-off-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-on: http://openocd.zylin.com/1808
Tested-by: jenkins
Reviewed-by: Jens Bauer <jens@gpio.dk>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
get_flash_bank_by_addr() iterates through all flash banks
trying to auto_probe() every bank, even if bank can belongs to
target other than requested, and this other target can be
in non-halted state, which leads to error message and
operation abort.
Same situation in gdb_new_connection() and gdb_memory_map():
get_flash_bank_by_num() tries to auto_probe() requested bank,
so first get bank by get_flash_bank_by_num_noprobe(), check
if it belongs to current connection's target and skip
get_flash_bank_by_num() (actually autoprobing) if not.
Change-Id: I48b3f93dddcd9283394f14ad2de3248397c75ab3
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/1813
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add a command to specify the serial string and pass it to the find helper.
Actual matching was already supported for both serial and product but was
using hard coded string indices. Instead use the indices from the device
descriptor.
Change-Id: I17c7538e5ad301ef41eace1ee70a202adab23bb4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1816
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
