add refresh command for lattice devices
rename gowin reprogram to refresh
rename virtex2 program to refresh
Change-Id: I9da83a614b96da3e947ac4608b0a291b1d126914
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7839
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on cologne
chip gatemate devices.
Change-Id: Ifa1c4ca6e215d7f49bd21620898991af213812e9
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7838
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on intel devices using
a proxy bitstream.
Change-Id: Ib947b8c0dd61e2c6fa8beeb30074606131b1480f
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7837
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on xilinx devices
using a proxy bitstream.
Change-Id: I68000d71de25118ed8a8603e544cff1dc69bd9ba
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7836
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on efinix trion and
titanium devices using a proxy bitstream.
Change-Id: I4a851fcaafe832c35bd7b825d95a3d08e4d57a7b
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7826
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on lattice
certus and certus po devices.
Change-Id: I6a8ec16be78f86073a4ef5302f6241185b08e1c6
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7825
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on lattice
ecp5 devices.
Change-Id: I4a4a60f21d7e8685a5b8320b9c6ebdc2693bbd21
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7824
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on lattice
ecp2 and ecp3 devices.
Change-Id: I39028aba47a74a0479be16d52d318f4bff7f2ed4
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7823
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Jtagspi is using a proxy bitstream to "connect" JTAG to the
SPI pins. This is not possible with all FPGA vendors/families.
In this cases a dedicated procedure is needed to establish such
a connection.
This patch adds a jtagspi-mode for these cases. It also adds the
needed interfaces to jtagspi and the pld-driver so the driver
can select the mode and provide the necessary procedures.
For the cases where a proxy bitstream is needed, the pld driver
will select the mode and provide instruction code needed in this
case.
Change-Id: I9563f26739589157b39a3664a73d91152cd13f77
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7822
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
at91sam7 flash driver allocates a flash bank based on detected flash
structure.
Use calloc() instead of malloc() - struct flash_bank has to be zeroed.
While on this:
Return error in case of struct flash_bank or driver_priv allocation fail.
Set default_padded_value and erased_value.
Use strdup() on bank->name, pointer is freed in flash_free_all_banks()
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Id890496bfbadb7970ef583256aa4f30a7bff832f
Reviewed-on: https://review.openocd.org/c/openocd/+/7884
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Recent commit 62f76b2169 ("flash/nor: add support for Nuvoton
NPCX4/K3 series flash") introduces a memory leak for a missing
free() on early return for an error.
Add the free() on the return path on error.
Change-Id: Ica8568a986802e23df2ab7bed4e8cc4bbb6305a5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 62f76b2169 ("flash/nor: add support for Nuvoton NPCX4/K3 series flash")
Reviewed-on: https://review.openocd.org/c/openocd/+/7894
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Previously, if a pin was configured as ADAPTER_GPIO_INIT_STATE_INPUT and
its drive value was ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL, initialize_gpio
would configure the pin as an output.
The set_gpio_value function is optimized to not set the direction for
pins configured as ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL as it only needs to
be set once. When initialize_gpio performs this setup, it checked only
that the drive value was ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL to set the
output direction but did not exclude input pins which have already had
their direction set.
Now, input pins are ignored when initialize_gpio checks for
ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL to set the mode to output.
Fixes: ace028262b ("drivers/am335xgpio: Migrate to adapter gpio commands")
Change-Id: I9ea502c400ea4ffae37080b9cee891ca9176a47d
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7877
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Steve Marple <stevemarple@googlemail.com>
Previously, if the image file was less than 9 bytes long,
it was assumed to be an error when it could be a binary
image file. This patch makes OpenOCD detect these cases
as binary files.
Change-Id: I5b4dad2b547786246887812ac75907378fe58671
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7880
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This patch unifies the lines printed by the "bp" command
so that different types of breakpoints are printed in
the same format.
Change-Id: Ic1335eda1c58072a334aed9cf0011431c8ec86a4
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7861
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Now internal watch/breakpoint will not be removed in case
of error during removing triggers from hardware.
Also change signature of some functions (for deletion
bp/wp) to print message in case of some error.
Change-Id: I71cd1f556a33975005d0ee372fc384fddfddc3bf
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7738
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Previously, if a pin was configured as ADAPTER_GPIO_INIT_STATE_INPUT and
its drive value was ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL, initialize_gpio
would configure the pin as an output.
The set_gpio_value function is optimized to not set the direction for
pins configured as ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL as it only needs to
be set once. When initialize_gpio performs this setup, it checked only
that the drive value was ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL to set the
output direction but did not exclude input pins which have already had
their direction set.
Now, input pins are ignored when initialize_gpio checks for
ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL to set the mode to output.
Change-Id: I4fc7a8132a6b00c7f213ec9fd05c7bbb37ee5f20
Fixes: 0dd969d83b ("drivers/bcm2835gpio: Migrate to adapter gpio commands")
Signed-off-by: Brandon Pupp <bpupp@xes-inc.com>
[vfazio: update commit message]
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7862
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
add new i2c bit-banging feature, we can now connect in JTAG with the SoC
target and in i2c with the main board components at the same time.
Change-Id: I8e4516fe1ad5238e0373444f1c3c9bc0814d0f52
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7796
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
