The XMC1000 family uses a very different flash interface from XMC4000.
Tested on XMC 2Go and XMC1100 Boot Kit.
Change-Id: I3edaed420ef1c0fb89fdf221022c8b04163d41b3
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3418
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Part IDs taken from
Atmel-42402C-SAM L22_Datasheet_Complete-01/2016
(revision C)
Change-Id: I1eb76a92097a8327da10faa0551e7fc962a549f8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3426
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Before this change jim_target_reset() checked examined state of a target
and failed without calling .assert_reset in particular target layer
(and without comprehensible warning to user).
Cortex-M target (which refuses access to DP under active SRST):
If connection is lost then reset process fails before asserting SRST
and connection with MCU is not restored.
This resulted in:
1) A lot of Cortex-M MCUs required use of reset button or cycling power
after firmware blocked SWD access somehow (sleep, misconfigured clock etc).
If firmware blocks SWD access early during initialization, a MCU could
become completely inaccessible by SWD.
2) If OpenOCD is (re)started and a MCU is in a broken state unresponsive
to SWD, reset command does not work even if it could help to restore communication.
Hopefully this scenario is not possible under full JTAG.
jim_target_reset() in target.c now does not check examined state
and delegates this task to a particular target. All targets have been checked
and xx_assert_reset() (or xx_deassert_reset()) procedures were changed
to check examined state if needed. Targets except arm11, cortex_a and cortex_m
just fail if target is not examined although it may be possible to use
at least hw reset. Left as TODO for developers familiar with these targets.
cortex_m_assert_reset(): memory access errors are stored
instead of immediate returning them to a higher level.
Errors from less important reads/writes are ignored.
Requested reset always leads to a configured action.
arm11_assert_reset() just asserts hw reset in case of not examined target.
cortex_a_assert_reset() works as usual in case of not examined target.
Change-Id: I84fa869f4f58e2fa83b6ea75de84440d9dc3d929
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2606
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Cortex-M0+ and M4 motor control MCUs KV10, KV11, KV30, KV31,
KV42, KV44 and KV46 added to SDID identification.
Watchdog disable code changed to work on Cortex-M0+ (KV1x)
Protection size set to 1K for 16K flash devices (KV10Z16)
- cherry picked from Andrey Smirnov's change #2051
Change-Id: Ia6f4868eaf7e2cb6ad6a736210c703a67e0027be
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3235
Tested-by: jenkins
Reviewed-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
To avoid conflicts between flash drivers being added, consistently use
an alphabetical sort order for the three places new drivers get added:
* Makefile.am NOR_DRIVERS (note: automake disallows a trailing backslash)
* drivers.c struct flash_driver forward declarations
* drivers.c flash_drivers array
Change-Id: Idcd6a8e12821ef10958a6b3ad7bac0dc63cadd08
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3417
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
FreeRTOS use an array to store ready task. The array size is
configMAX_PRIORITIES. In the current implementation, the code try to access 1 more priority if the helper from freeRTOS contrib is used.
This has effect of detecting bad thread. This patch correct this and have been tested on
a code with more than 12 task.
Change-Id: Id229f0b2c4bf1aab87a2a69be174cc9b6dda00cb
Signed-off-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-on: http://openocd.zylin.com/3400
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add new structure for for working with FPU thread in thread view.
This modification support both stacking.
When FPU is activated, LR must be validated to check if the FPU
register are push on the stack. This is mandatory to find the correct
stack pointer position.
the modified code was inspired and adapted from
88d2003bb8
Change-Id: I6641926aa14e7216cacb399cbc8bb0db324cc9fc
Signed-off-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-on: http://openocd.zylin.com/3397
Tested-by: jenkins
Reviewed-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-by: Harry Zhurov <harry.zhurov@gmail.com>
Reviewed-by: Anton Gusev
Reviewed-by: Михаил Цивинский <mtsivinsky@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested with MKE04Z8VTG4, MKE02Z64VLC4 and MKE02Z64VLD2.
Change-Id: I606e32a2746a3b96d3e50f3656ba78d40c41c1ea
Signed-off-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-on: http://openocd.zylin.com/3380
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This feature is required for boards that use a programmatical way
to reset the cpu, like the TI Pandaboard with OMAP4. The board only
has a 14 pin JTAG header that doesn't feature SRST and is reset by
direct write to the PRM_RSTCTL register.
iMX6 can be reset through triggering the on-chip watchdog, but for these
methods to work reliably, access through the AHB-AP without interaction
with the CPU core is necessary.
Change-Id: I9a07a536adda83cc2f93e504384c8c7f0306220b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3359
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a 'ftdi_location' command to select an adapter by usb
bus number and port path.
This is helpful if you have a rack full of adapters in a testing or
manufacturing setup where the only constant is the physical usb bus
location of the adapter you want to address. Vid:Pid are not unique,
serial number _may_ be unique (and maybe not with embedded adapters) but
will change when a new target is plugged.
Specifying a location allows to understand instantly which board failed
bringup or testing.
Change-Id: I403c7c6c8e34fe42041b3f967db80f3160a4f1a3
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3351
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Add support for S6E2DH MainFlash. VFlash is not implemented.
Briefly tested with SK-FM4-176L-S6E2DH V110 board.
Change-Id: If7c523d8c75307bc1494bbf4cca3eed0272e8e01
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3158
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
