Use loaders that have been built for cortex-m0, making them usable for both
cortex-m0 and cortex-m3 families.
Change-Id: Ifd82be87eaec2cb96464290c80800cec3630d619
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/604
Tested-by: jenkins
Fix following warning message logged by udev at start
udevd[421]: SYSFS{}= will be removed in a future udev
version, please use ATTR{}= to match the event device,
or ATTRS{}= to match a parent device, in
/etc/udev/rules.d/95-openocd.rules:81
Change-Id: I6de935c13a3327e3d718c110f97d19b9847ceca5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/552
Tested-by: jenkins
Reviewed-by: Luca Bruno
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This enable the stm32f2x flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 1048576 bytes from file stm32f4x.bin in 30.453804s (33.625 KiB/s)
after - wrote 1048576 bytes from file stm32f4x.bin in 23.679497s (43.244 KiB/s)
This also fixes a bug that was in the old flash loader.
The old loader waited while bit16 of the status reg was 0, the new
loader waits until this bit is 0 as stated in the flash spec.
Bizarrely this bug did not effect programming on any tested parts.
Change-Id: I3efc94d42cbe81283673a8f4203700638080af6e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/460
Tested-by: jenkins
This enable the Stellaris flash driver to use the asynchronous
algorithm support.
Speed increase is as follows:
before - wrote 65536 bytes from file test.bin in 5.486040s (11.666 KiB/s)
after - wrote 65536 bytes from file test.bin in 2.274001s (28.144 KiB/s)
Change-Id: I9004c9aadffa1ae3b0cbf908e6549b5b1f794508
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/403
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Correct the offset to the read pointer when clearing it on error.
Also restrict the instruction set to armv6-m so the flash driver can be
used on Cortex-M0 parts with the same flash controller.
Change-Id: I380f9dabcc41fb6e4d43a7e02f355e2381913f39
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/399
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Jonathan Dumaresq <jdumaresq@cimeq.qc.ca>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This corrects permissions on the FTDI chip on the xds100v2 debugger
enabling normal users to access it.
Change-Id: I0f6618692ebdee6284eee28f9e612e68782c4d78
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Reviewed-on: http://openocd.zylin.com/188
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
add support for checking target against the device CLASS rather
then just the PARTNO.
This change also adds the new LM4F family (Blizzard).
Change-Id: Ia9d1e33f1f1c2817c0039a2232ecf932fae072f9
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/161
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The DLP Design DLP-USB1232H UART/SPI/JTAG module is based on an FTDI FT2232H
chip. Among other things, it can used as JTAG programmer if connected to
the JTAG target properly. I have successfully wired the module to an
Olimex STM32-H103 eval board and flashed a firmware onto that using OpenOCD.
The setup details and schematics are documented at:
http://randomprojects.org/wiki/DLP-USB1232H_and_OpenOCD_based_JTAG_adapter
Change-Id: I5eb9255a61eeece233009bee77d7dc3b5d1afb8b
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reviewed-on: http://openocd.zylin.com/20
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
Let the target algorithm be running in the background and buffer data
continuously through a FIFO. This reduces or removes the effect of latency
because only a very small number of queue executions needs to be done per
buffer fill. Previously, the many repeated target state changes, register
accesses (really inefficient) and algorithm uploads caused the flash
programming to be latency bound in many cases. Now it should scale better
with increased throughput.
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Most serial adaptors are identified by udev with SUBSYSTEM=tty and
without DEVTYPE. This patch fix udev rules to work with any listed
tty-based adaptor. It has been tested with a FTDI-based Bus Pirate.
Signed-off-by: Luca Bruno <lucab@debian.org>
Added a Perl script to contrib that uses the header files in StellarisWare complete Firmware Development Package provided by TI/Luminary to generate a new list of device IDs
Used Perl script and revision 6734 of TI/Luminary StellarisWare to update device IDs
