If a new JTAG command is added, then GCC will complain that
enumeration value not handled in switch. This is the only driver not
to have a default case, so add it.
Change-Id: Icb838087bb7525d057a911bd256300e256da1668
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://openocd.zylin.com/5333
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If a new JTAG command is added, then GCC will complain that
enumeration value not handled in switch. Make this consistent with
other drivers, and add a 'default' case.
Change-Id: I66d6d0db3fcae93ea246f2d4882ffff5dec14693
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://openocd.zylin.com/5340
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
In preparation for supporting the ARM MCRR and MRRC commands which will
require using two 32-bit registers to read/write a 64-bit internal
register, extract the common logic to read/write from/to a register
to/from DCC and make that parameterized such that we can do this through
not just r0.
Change-Id: Iadb73f5cde8cf5961b5a18ddd198bf39d791e610
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-on: http://openocd.zylin.com/5227
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The variable gw16012_port is of type uint16_t.
There is no need for a cast to print it.
Change the format modifier to PRIx16
Change-Id: I16fe688b9d235bae46525635d07849a00fba9548
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5195
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
GDB uses the vRun packet if available to restart a running process in
extended remote mode. Support this like the R packet and set the
semihosting command-line to allow it to be specified from GDB.
Change-Id: I9cb812b22170630f782113c9927e46e0cd5b1f0f
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5186
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Armv7a is able to read and write memory at un-aligned address, but
only when bit SCTLR.A (Alignment check enable) is zero and the
address belongs to a memory space with attribute "Normal" (see [1]
chapter A3.2.1 "Unaligned data access"). In all the other cases
the memory access will trigger an alignment fault data abort
exception.
Memory attributes are explained in [1] chapter A3.5 "Memory types
and attributes and the memory order model".
Disabling the MMU cause a change in memory attribute, as explained
in [1] chapter B3.2 "The effects of disabling MMUs on VMSA
behavior".
This can cause several issues. e.g. a SW breakpoint on un-aligned
4-byte Thumb instruction, set when MMU is on, can be impossible to
remove when MMU turns off.
While is possible to check all the possible conditions before an
un-aligned memory access, it's clearly more maintainable to skip
such complexity and only perform aligned accesses.
Check the alignment and eventually modify the data size before
calling the functions cortex_a_{read,write}_cpu_memory_slow().
Change the comment in the two functions above to comply with the
new behaviour.
[1] ARM DDI 0406C.d - "ARM Architecture Reference Manual, ARMv7-A
and ARMv7-R edition"
Change-Id: I57b4c11e7fa7e78aaaaee4406a5734b48db740ae
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5138
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Issue has been found when I tried to read 64 MiB QSPI flash bank.
Bank is memory mapped, default_flash_read() is used for 'flash read_bank'
command. OpenOCD consumed as much as 6.8 GiB of RAM during this
process. Investigation showed that this happens because JTAG queue
is not limited in any way. OpenOCD queues 16 millions of AP reads
allocating all corresponding data structures.
Most of this memory is allocated in:
cmd_queue_alloc (commands.c) - 4.2 GiB
dap_cmd_new (adi_v5_jtag.c) - 2.25GiB
This patch implements a pool of "struct dap_cmd" objects using
linked list. Objects are taken from a pool in "dap_cmd_new()" and
returned to the pool when they are not needed. Size of the pool
is limited to 64K of objects, JTAG queue is forcibly executed
when this limit is reached.
Checked with Valgrind and Clang analyzer - no new warnings.
Change-Id: I5aaaecce5ed71414f7965a2598f49742f6a6b2b5
Signed-off-by: Bohdan Tymkiv <bhdt@cypress.com>
Reviewed-on: http://openocd.zylin.com/4948
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Correct check for end-of-region is:
$BASE + $LEN > $ADDRESS
And it is currently (wrongly) calculated as:
$ADDRESS > $BASE - $LEN
Change-Id: If10bfee19b0c7dbc085731ac1eda943f5d8a36a3
Signed-off-by: Piotr Kasprzyk <ciri@ciri.pl>
Reviewed-on: http://openocd.zylin.com/4798
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Make driver_priv point directly into the corresponding chip bank structure
and add a pointer to it to get back to its chip when it's needed. This
removes the need to keep track of any bank number, either global or chip-
local.
In addition, it simplifies the cases where the chip structure was just used
to access the chip bank fields; now they are directly accessible.
Change-Id: Iaa353cd4fa7d8ff94c2ef69028c7cb32fade0420
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/4775
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The current code checks the count to determine whether to read bytes or
words. However it fails to consider whether the base address is suitably
aligned.
Instead use the target_read_buffer() function which is for exactly this
purpose and generates optimal accesses with natural alignment.
Change-Id: I32ab5417890ee2219902df1529bc220fe353b4c7
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3217
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The preverify option allows to check whether flashing is necessary.
If the target is flashed often/automatically this can save time and
preserve the flash. This is expecially helpful in CI environments.
Change-Id: Iead0a269e1a772b751d4dd9e8b53b2fecc874624
Signed-off-by: Moritz 'Morty' Strübe <moritz.struebe@redheads.de>
Reviewed-on: http://openocd.zylin.com/5292
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
I think that libusb_handle_events_timeout_completed is supposed to make
progress or time out, but sometimes we hit a case where it makes no
progress, and mpsse_flush() loops forever. This wall clock timeout
notifies the user that this is going on.
When I wrote this code, this bug would reproduce every hour or two, but
right now it's not happening for me.
Change-Id: I7eb66f43462298e263a48048aa0c8769095661eb
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4767
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
According to the reference manual it should be 0x40000000. Flashing (and
booting) a firmware with this MSC base was successful.
Change-Id: I739e67d36555b8170a3b8e26f54cf1c09ce8424b
Signed-off-by: Christian Meusel <christian.meusel@posteo.de>
Reviewed-on: http://openocd.zylin.com/5263
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix expression "(pin_status | 0x4)" which was always true rather than
testing a bit. Untested - was clearly not expressing the intent of the
author by inspection. Found by automated tooling and rtrieu@google.com.
Signed-off-by: Seth LaForge <sethml@google.com>
Change-Id: I4bb91e60e8ce9757bf21976cc48de6f85a39c68d
Reviewed-on: http://openocd.zylin.com/5301
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The C standard says that errno is set to ERANGE if an out-of-range value
is returned by strtol, strtoul, et. al., but it does not say that errno
is cleared if the function is successful (and, indeed, it is not on
glibc). This means that, if errno is ERANGE before strtol is called, and
if the value to be converted is exactly the maximum (or, for a signed
conversion, the minimum) legal value, COMMAND_PARSE_NUMBER will
erroneously indicate that the value is out of range.
Change-Id: I8a8b50a815b408a38235968f1c1d70297ea1a6aa
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5298
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
