After setting adapter speed to some values, the driver
shows the real speed little bit higher.
Although it does not impose a problem from technical point
of view because the difference is smaller than usual speed error,
it looks at least strange to the user. The documentation reads
that real frequency should be same or lower than requested.
Use proper rounding in speed -> delay and delay -> speed
conversions.
Change-Id: I1831112cc58681875548d2aeb688391fb79fa37f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7261
Tested-by: jenkins
Reviewed-by: Jonathan Bell <jonathan@raspberrypi.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
bitbang_swd_exchange(rnw=true,...) calls bitbang_interface->swd_write()
with swdio clamped to 0.
bitbang_swd_write_reg() reads 1 turnaround bit, 3 ack bits
and 1 turnaround by one call to bitbang_swd_exchange()
and then switches SWDIO to output.
AFAIK all bitbang interfaces switch SWDIO GPIO direction immediately
in bitbang_interface->swdio_drive().
The GPIO now drives SWDIO line to the value stored in the output register
which is always zero from previous bitbang_swd_exchange(rnw=true,...).
In case the following data bit (bit 0) is 1 we can observe a glitch
on SWDIO:
_____ out 1 ____
HiZ/pull-up ----\ /
\ /
\______ out 0 ______/
swdio_drive(true) swd_write(0,1)
The glitch fortunately takes place far enough from SWCLK rising edge
where SWDIO is sampled by the target, so I believe it is harmless
except some corner cases where the reflected wave is delayed on long
line.
Anyway keeping electrical signals glitch free is a good practice.
To keep performance penalty minimal, pre-write the first data
bit to SWDIO GPIO output buffer while clocking the turnaround bit.
Following swdio_drive(true) outputs the pre-written value
and the same value is rewritten by the next swd_write()
instead of glitching SWDIO.
Change-Id: I72ea9c0b2fae57e8ff5aa616859182c67abc924f
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7260
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The OpenJTAG driver logs "num_cycles > 16 on run test" warning
whenever the JTAG_RUNTEST operation cycle count is larger than 16.
Instead of logging the warning and only running the first 16 TCLK
cycles, remove the warning and queue up multiple operations of up
to 16 cycles each.
Signed-off-by: N S <nlshipp@yahoo.com>
Change-Id: Id405fa802ff1cf3db7a21e76bd6df0c2d3a0fe61
Reviewed-on: https://review.openocd.org/c/openocd/+/7420
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
URL for Microsoft documentation on IgnoreHardwareSerialNumber
redirects to generic USB driver landing page instead of specific
article. Update link to go to correct page.
Signed-off-by: N S <nlshipp@yahoo.com>
Change-Id: Ifac6c730a1438242cdfe0a0a2867e043e03ceec7
Reviewed-on: https://review.openocd.org/c/openocd/+/7439
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This generalizes the little endian CRC32 function used in the OR1K
target and moves it to a common helper, so that other places do not need
to reinvent the wheel. It is directly used in the OR1K target.
Change-Id: I0e55340281a5bfd80669bb1994f3a96fecc1248a
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7415
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Polling the target makes no harm during PSoC 4 flash write in the current
OpenOCD code. Don't mask it.
Change-Id: I6625ded0162ee3a96b92188844d0d2d6c30101c2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7162
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The commands 'jtag newtap' and 'swd newdap' have to work either on
HLA transport and on standard JTAG/SWD. Having a dedicated
implementation for HLA is a non-sense.
Reuse the generic code jim_jtag_newtap() and drop the files
hla_tcl.[ch] as they are now empty.
Change-Id: I9dabbdc2a6f338f23b2fd3ed1a4dc3da0200c080
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7428
Tested-by: jenkins
The same code is currently used for commands 'jtag newtap' and
'swd newdap' (plus dapdirect versions), but for SWD case the code
skips the parsing of the command line as not every flag is used.
This has the drawback that syntax errors get unchecked.
Move the check about the transport so the command line get always
parsed even when the corresponding flags are not useful.
Change-Id: I596c3beb04e9e8a9ebe6ee68a61395b679d43b3e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7427
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Enhancing the editor / IDE experience with the use of the language
server protocol (lsp) is getting more and more common. The most widely
used lsp implementation for C/C++ outside of Redmond is clangd.
Clangd uses compile_commands.json, that contains the compiler invocation
for each compilation unit, to get the required $CFLAGS to successfully
located header files etc. This is best automatically generated from with
bear on Makefile based build systems. Hence, there is little value in
adding it to the git repo.
In addition, clangd generates cache files in the .cache folder. Again,
there is no reason in tracking it with git.
Change-Id: Ic5165d10aca3a1cc9e9398af9dd2fbf0977608b3
Signed-off-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7414
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The rtos hwthread has been merged in 2019 with commit 85ba2dc4c6
("rtos/hwthread: add hardware-thread pseudo rtos").
During review in patchset 19 the name of the rtos has been changed
from 'hawt' to 'hwthread'.
Some target config file was already merged ready for hwthread, but
keeping the relevant lines commented and still reporting the old
name.
Enable rtos hwtread to the target that were supposed to use it.
Fix the name of the rtos.
Change-Id: I877862dcdba39f26462bb542bac06d1a5f5f222d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7384
Tested-by: jenkins
The line reset SWD sequence is used quite often in SWD multidrop mode.
Prevent the ugly connect/disconnect adapter firmware bug workaround
to be called before each line reset.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Id85bff075dba9077e4e501e2cdcfd64d5d9d0531
Reviewed-on: https://review.openocd.org/c/openocd/+/7381
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DAP_TransferBlock command saves n - 3 bytes in comparison to DAP_Transfer,
where n is number of transfers.
Use DAP_TransferBlock optionaly to save some USB bandwidth.
The change increases the speed of the write transfer
from 40 KiB/s to 42 KiB/s @ USB FS, adapter speed 1000.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ifde0159cfd44481d2b81b90daa088e731c03e26d
Reviewed-on: https://review.openocd.org/c/openocd/+/7372
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DAP write transaction occupies 5 bytes of a command packet.
DAP read transaction needs just one byte in a command packet
and expect 4 bytes in a response.
The fixed maximal number of transactions in a packet caused
packet filling less than optimal.
Compute both command and expected response sizes based on
read or write direction of each transaction.
Run the queue if one of sizes does not fit into a packet.
The change increases the speed of the mostly read transfer
from 36 KiB/s to almost 40 KiB/s @ USB FS, adapter speed 1000
due to reduction of adapter inserted RDBUFF reads.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ib70812600eaae0403b8ee8673b6f897348496569
Reviewed-on: https://review.openocd.org/c/openocd/+/7364
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
USB bulk backend needs to avoid zero sized USB packets
sent after each full sized packed for performance reasons.
HID backend uses fixed size HID reports so the full size
of the report can be utilized.
Introduce packet_usable_size to reflect it.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I34094c9edac5730624480711cbd6aa65883c47c7
Reviewed-on: https://review.openocd.org/c/openocd/+/7363
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
