Add GPIO extender initial configuration that is needed to configure
some important GPIOs and ensure that the dev board is ready to work.
Add i2c_write function that make a write transfer to any slave device.
Give a new Product ID to ANGIE to make it different than the non
programmed ANGIE.
Change-Id: I0a8dacb7fe218145b7d3ed1cb75f106ed6256714
Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8072
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some OpenOCD command gets fragment of TCL scripts as command-line
argument, fragments that will be kept and executed later on.
E.g. the command 'configure' gets the body of an OpenOCD event:
$TARGET configure -event halted {TCL code}
These commands store the argument as a Jim_Obj and pass it to the
jimtcl interpreter when the TCL fragment has to be executed.
Using Jim_Obj as storage is relevant to let the jimtcl interpreter
to recover extra info of the TCL fragment, like the file-name and
the line-number that contain the fragment, that will be printed
out in case of run-time errors.
While converting the commands to COMMAND_HANDLER, we should avoid
storing the argument as C strings otherwise we will loose precious
info in case of run-time errors making challenging the debugging
of such TCL fragments.
Extend the struct command_invocation to contain the array that
points to the Jim_Obj of the command arguments.
This will be used while converting commands to COMMAND_HANDLER.
Change-Id: If37c5f20e9a71349f77ba1571baf1e6778e28aa5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8057
Tested-by: jenkins
S32K General-Purpose Microcontrollers
Scalable, low-power Arm® Cortex®-M series-based microcontrollers AEC-Q100
qualified with advanced safety and security and software support for
industrial and automotive ASIL B/D applications in body, zone control,
and electrification.
Change-Id: I4143258535437c18b81802436267bfd561de9d31
Signed-off-by: David Vidrie Leon <davidvidrie@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8012
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
When Linux HID driver binds the USB endpoints of the adapter,
'lsusb' fails to read all the reports and prints
** UNAVAILABLE **
Detect this case and alert the user, providing also the proper
command to unbind the driver before running the script again.
Put this test at the end of the output, so user can easily see it.
Change-Id: Iaca00040e666b62ceebe4b842a24932799bde56a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8046
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some devices with an internal multi-tap JTAG router require a vendor
specific bypass instruction to bypass the master TAP when addressing
slave taps internal to the same device. On these devices the standard
bypass instruction bypasses the whole device.
Change-Id: I4506f0e67c9e4dfe39b7fa18c63d67900313e594
Signed-off-by: Henrik Nordström <henrik.nordstrom@addiva.se>
Reviewed-on: https://review.openocd.org/c/openocd/+/8041
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Real dumps from adapters I have access to.
Serial numbers have been manually edited but are still consistent.
While there, rename a file to correct the USB PID.
Change-Id: I4fd0b6661d55294c2ce0ecbead765def1143880c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e0059dfffa ("doc: usb_adapters: add lsusb dump of few adapters")
Reviewed-on: https://review.openocd.org/c/openocd/+/8047
Tested-by: jenkins
If the remote_bitbang host does not execute requests immediately,
delays performed inside OpenOCD can be lost. This option allows
the delays to be sent to the remote host so that they can be
queued and executed in order.
Signed-off-by: Jeremy Herbert <jeremy.006@gmail.com>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Change-Id: Ie1b09e09ea132dd528139618e4305154819cbc9e
Reviewed-on: https://review.openocd.org/c/openocd/+/7472
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
USB HS based CMSIS-DAP v1 (HID) adapters found
on Atmel/Microchip Xplained Pro development boards.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I62a4b656dc6dce27da386e906d87088befc2bcbf
Reviewed-on: https://review.openocd.org/c/openocd/+/8038
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Introduce 'cmsis-dap quirk' command to enable and
disable quirk mode.
If enabled, disconnect and connect before a switch
sequence and do not use multiple packets pipelining.
Change-Id: I6576f7de9f6c98a25c3cf9eec9a456a23610d00d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7966
Tested-by: jenkins
This adds new command characters to make SWD work with the new split
jtag and swd operations of bitbang.
The command characters are as follows:
O - SWDIO drive 1
o - SWDIO drive 0
c - SWDIO read request
d - SWD write 0 0
e - SWD write 0 1
f - SWD write 1 0
g - SWD write 1 1
Documentation has been updated accordingly. The new commands will be
used by an adapted version of the jtag-openocd applet of the "Glasgow
Debug Tool" (https://github.com/glasgowEmbedded/Glasgow). It has been
tested against an stm32f103 and an at91samd21 target.
contrib/remote/bitbang/remote_bitbang_sysfsgpio.c has also been adapted
to support SWD via the new command set. Some limited testing has been
done using a Raspberry Pi 2 with an stm32f103 and an at91samd21 target
attached.
Change-Id: I8e998a2cb36905142cb16e534483094cd99e8fa7
Signed-off-by: Manuel Wick <manuel@matronix.de>
Signed-off-by: David Ryskalczyk <david.rysk@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6044
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is useful when using the SEGGER RTT tooling, as the SEGGER RTT
tool J-Link RTT Viewer version 7.84f requires that it receives a
messages immediately after connecting. Otherwise it will give a timeout
and it will not connect.
Change-Id: I9240a1b6a93cd5c0fbd18292afb33b89013d78bf
Signed-off-by: Thiemo van Engelen <tvanengelen@victronenergy.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7752
Tested-by: jenkins
Reviewed-by: zapb <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'kitprog' with subcommands instead of individual
commands with 'kitprog_' prefix.
The old command is still available to ensure backwards compatibility,
but is marked as deprecated.
Change-Id: I7f0d447939819ffc488a3d7a8de672b58887127f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7967
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use a command group 'cmsis-dap' with subcommands instead of individual
commands with 'cmsis_dap_' prefix.
The old commands are still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I75facb7572a86354c2ce6144aa7fadf3b5a6db4e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/7963
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
