- add 'dap create' command to create dap instances
- move all dap subcmmand into the dap instance commands
- keep 'dap info' for convenience
- change all armv7 and armv8 targets to take a dap
instance instead of a jtag chain position
- restructure tap/dap/target relations, jtag tap no
longer references the dap, daps are now independently
created and initialized.
- clean up swd connect
- re-initialize DAP also on JTAG errors (e.g. after reset,
power cycle)
- update documentation
- update target files
Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4468
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Extend the CTI abstraction to be accessible from TCL and
change the 'target' command to accept a cti 'object' instead of a
base address. This also allows accessing CTI instances that are not
related to a configured target.
Change-Id: Iac9ed0edca6f1be00fe93783a35c26077f6bc80a
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4031
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Since OpenOCD basically allows to perform arbitrary actions on behalf of
the running user, it makes sense to restrict the exposure by default.
If you need network connectivity and your environment is safe enough,
use "bindto 0.0.0.0" to switch to the old behaviour.
Change-Id: I4a4044b90d0ecb30118cea96fc92a7bcff0924e0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4331
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
While on it
- change some occurrences of gdb to GDB if it refers GDB software
(as oposed to a gdb command)
- add some xrefs
- give more meaningful example of target event definition
- remove obsoleted example of GDB hook-step
Change-Id: Ia2e26021d57f675acfa1de704f6c3e81c22bb8bf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4444
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This change contains an alternative to Matthias Welwarsky's #4130
(target-prefixed commands) and to #4293 (event handlers).
get_current_target() must retrieve the target associated to the current
command. If no target associated, the current target of the command
context is used as a fallback.
Many Tcl event handlers work with the current target as if it were
the target issuing the event.
current_target in command_context is a number and has to be converted
to a pointer in every get_current_target() call.
The solution:
- Replace current_target in command_context by a target pointer
- Add another target pointer current_target_override
- get_current_target() returns current_target_override if set, otherwise
current_target
- Save, set and restore current_target_override to the current prefix
in run_command()
- Save, set and restore current_target_override to the event invoking
target in target_handle_event()
While on it use calloc when allocating a new command_context.
Change-Id: I9a82102e94dcac063743834a1d28da861b2e74ea
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4295
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This fixes parsing of several documentation files which do not have
dot in the filename.
style.txt change fixes doxygen warnings and ensures proper display of
comment begin/end instructions in HTML.
Tested with Doxygen 1.8.13.
Change-Id: I9fd9ac3b51b47076b8fdbd3e93b90c3eba9b9631
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4342
Tested-by: jenkins
This commit contains a rewrite of the jtagspi protocol and covers both
changes in the jtagspi.c openocd driver and the bscan_spi
(xilinx_bscan_spi) proxy bitstreams. The changes are as follows:
1. Always perform IR scan to ensure proper clearing of BYPASSed DRs.
2. Insert alignment cycles for all BYPASSed TAPs:
The previous logic was erroneous. The delay in clock cyles from a bit
written to the jtag interface to a bit read by the jtag interface is:
* The number of BYPASSed TAPs before this (jtagspi) tap
* The length of the jtagspi data register (1)
* The number of BYPASSed TAPs before this one.
I.e. it is just the number of enabled TAPs. This also gets rid of the
configuration parameter DR_LENGTH.
3. Use marker bit to start spi transfer
If there are TAPs ahead of this one on the JTAG chain, and we are in
DR-SHIFT, there will be old bits toggled through first before the first
valid bit destined for the flash.
This delays the begin of the JTAGSPI transaction until the first high bit.
4. New jtagspi protocol
A JTAGSPI transfer now consists of:
* an arbitrary number of 0 bits (from BYPASS registers in front of the
JTAG2SPI DR)
* a marker bit (1) indicating the start of the JTAG2SPI transaction
* 32 bits (big endian) describing the length of the SPI transaction
* a number of SPI clock cycles (corresponding to 3.) with CS_N asserted
* an arbitrary number of cycles (to shift MISO/TDO data through
subsequent BYPASS registers)
5. xilinx_bscan_spi: clean up, add ultrascale
This is tested on the following configurations:
* KC705: XC7K325T
* Sayma AMC: XCKU040
* Sayma AMC + RTM): XCKU040 + XC7A15T, a board with integrated FTDI JTAG
adapter, SCANSTA JTAG router, a Xilinx Ultrascale XCKU040 and a Xilinx
Artix 7 15T. https://github.com/m-labs/sinara/wiki/Sayma
* Custom board with Lattice FPGA + XC7A35T
* CUstom board with 3x XCKU115-2FLVA1517E
Change-Id: I7361e9fb284ebb916302941735eebef3612aa103
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Events reset-halt-pre, reset-halt-post, reset-wait-pre and
reset-wait-post are not used anywhere.
Change-Id: I9a0f94875b102d9b08f6c2fd9d73a9f05f8e8e79
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4285
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Renaming of all nrf51 NOR flash code to nrf5, as to prepare the
code for being able to flash nrf51 and nrf52 chips.
The nrf51 command is retained for backwards compatability.
"nRF5" is also the name Nordic Semiconductor uses to describe
both the nrf51 and nrf52 chips.
Change-Id: I5f4e3f1ec780184b28ad44f735a746e68908c502
Signed-off-by: Slowcoder <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4209
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
IDs for STM32F722, F723, F413 and F423 added, handling of PCROP
for F722/723 and additional nWPRT bits for F413/423 implemented.
The additional protection bit positions for F413/423 conflict
with other options bits for the F7xx variants, additionally the
last two sectors share a common bit.
Protection for F413 and F767/777 now use protection blocks
rather sectors for dealing with protections bits.
Checking for halted state in 'lock' and 'unlock' removed: When
PCROP is activated in F723, halted state is not detected properly,
but lock/unlock sequence is required to disable PCROP.
Tested with STM32F723E-Disco, STM32F413ZH-Nucleo.
Change-Id: Ie6ddab47a9ae8461087d369b4f289b7f9d1e031c
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4045
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change ftdi SWD driver and CMSIS-DAP to use it instead of LOG_DEBUG().
Change-Id: I17ba3de2086c7159209db61fba3faf067dfc5023
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3805
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
