Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.
Fix them with the same sed commands used for the other scripts:
sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)
Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Add driver for the RPC block in HF mode on Renesas R-Car Gen3 SoCs.
This driver allows operating the on-SIP HF memory.
Note that HF is CFI compliant flash, but it is not memory mapped,
hence the need to replace all the memory accessors and read/write
functions. The write function is entirely replaced to increase
performance and is Spansion/AMD specific, since there is no known
SIP with other HF from another vendor.
Add the following two lines to board TCL file to bind the driver on
R-Car Gen3 SoC using HyperFlash:
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME rpchf 0x08000000 0x4000000 2 2 $_CHIPNAME.a57.0
Change-Id: Ie18729d017eeb46e1363333ffe002d010dfc5ead
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5149
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
The fallback provided for the jtag_reset command always fails with a
strange message: 'Error: invalid command name "de"'
This is caused by incorrect quoting inside the warning message.
Fixes: c07b774e8f ("jtag: replace command "jtag_reset" with "adapter [de]assert"")
Change-Id: Icd47fca2b5a7b33474bfb0040e88193a0968f301
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5416
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
currently we have different types of same command group:
- starting with adapter_*
- starting with interface*
- without adapter or interface prefix.
Since interface name is already used, we can only use "adapter" command
group by keeping old commands as well.
Change-Id: Id0a1cb63a2ea6860c67ae1e7a3a06a37ddf464f4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4774
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fix comment of tested errors in asm src.
List all relevant errors in FLASH_ERROR mask: FLASH_PROGERR was missing
and any trial to re-program already programmed double word ended up
in the error bit held uncleared and flash write permanetly repeating
the error message until reset.
Lock the bank also after unsuccesfull write_block run.
Set async target algo block size to size of double word.
Remove warning in case of write_block success. In case of error
use LOG_ERROR instead of warning.
Change-Id: Ibf6d5e306a4c2eaa43de67d636b4902c737f02f3
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5360
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The original code paded the write chunk with random bytes by overrunning
the buffer. An user can easily regard the random bytes to
be a programming error.
Change-Id: Ib0f47b5bc406bc6a7c32f3d929bf324a17c7c1e1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5359
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Since commit 7f260f5009 native OpenOCD
command handlers should not directly use Jim_SetResult functions.
The Tcl result of a native command is built as concatenation of
command_print() strings and Jim_SetResult() is called after return
of the command handler.
Replace "wrong number of args" error messages (now not delivered to user)
by simply return ERROR_COMMAND_SYNTAX_ERROR
Change-Id: I40c1374a13859cefbdef68e0f1c13ab93538bd50
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5363
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The chip->hwid is uint32_t , fix the print format.
This was detected by TravisCI on OSX, where this triggers a build error.
Change-Id: I776a7bb50e396c8fccc24500dec4750190da7982
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5401
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Ilya Kharin <akscram@gmail.com>
Commit [1] was submitted in gerrit well before the conflicting
commit [2] get merged in master branch. While it was fine
committing in master branch [1] alone, it should not be
committed "as is" after [2].
Unfortunately gerrit did not complained committing [1] after [2].
The result is that master branch does not build anymore when the
driver xlnx-pcie-xvc is enabled at configure time by the optional
flag --enable-xlnx-pcie-xvc.
Apply to the driver the required changes as in [2].
While there, remove the duplicated struct xlnx_pcie_xvc_transports
and the struct field already implicitly initialized to zero.
[1] ff6d0704ec ("jtag: drivers: xlnx-pcie-xvc: Add support for
Xilinx XVC/PCIe")
[2] efd1d64222 ("adapter: switch from struct jtag_interface to
adapter_driver")
Change-Id: I5498479b802a231afbee1b845ae9775e1da7c728
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5402
Reviewed-by: Moritz Fischer <moritzf@google.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add driver for the SH QSPI controller. This SPI controller is often
connected to the boot SPI NOR flash on R-Car Gen2 platforms.
Add the following two lines to board TCL file to bind the driver on
R-Car Gen2 SoC and make SRAM work area available:
flash bank flash0 sh_qspi 0xe6b10000 0 0 0 ${_TARGETNAME}0 cs0
${_TARGETNAME}0 configure -work-area-phys 0xe6300000 -work-area-virt 0xe6300000 -work-area-size 0x10000 -work-area-backup 0
To install mainline U-Boot on the board, use the following procedure:
proc update_uboot {} {
# SPL
flash erase_sector 0 0x0 0x0
flash write_bank 0 /u-boot/spl/u-boot-spl.bin 0x0
# U-Boot
flash erase_sector 0 0x5 0x6
flash write_bank 0 /u-boot/u-boot.img 0x140000
}
Change-Id: Ief22f61e93bcabae37f6e371156dece6c4be3459
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
---
V2: - Add Makefile and linker script for the SH QSPI IO algorithm
- Include the algorithm code instead of hard-coding it
Reviewed-on: http://openocd.zylin.com/5143
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
A USB bulk write/read operation may fail with different errors:
LIBUSB_ERROR_TIMEOUT if the transfer timed out (and populates transferred)
LIBUSB_ERROR_PIPE if the endpoint halted
LIBUSB_ERROR_OVERFLOW if the device offered more data, see Packets and overflows
LIBUSB_ERROR_NO_DEVICE if the device has been disconnected
another LIBUSB_ERROR code on other failures
Current OpenOCD code is using the transfer size based error detection.
Which may not always work. For example for LIBUSB_ERROR_OVERFLOW as libusb
documentation says:
"Problems may occur if the device attempts to send more data than can fit in
the buffer. libusb reports LIBUSB_TRANSFER_OVERFLOW for this condition but
other behaviour is largely undefined: actual_length may or may not be accurate,
the chunk of data that can fit in the buffer (before overflow) may or may not
have been transferred."
This patch is refactoring code to use actual error return value for
error detection instead of size.
Change-Id: Iec0798438ca7b5c76e2e2912af21d9aa76ee0217
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4590
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for Xilinx Virtual Cable over PCIe JTAG controller.
It is commonly used in Xilinx based PCI Express designs with JTAG IP
in the FPGA fabric.
Access to the JTAG registers happens via the PCI Express extended
configuration space.
This can be used to debug soft-cores instantiated in the FPGA fabric.
The clang static checker doesn't find any new problems with this change.
Change-Id: Ib12ede0d1f26dacfda808d5e05b947b640c5bde7
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marex
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
This is a preparatory change, align the function name with the rest
of the API, no functional change.
Change-Id: I6a810d2a54edcd13ad9a87d24a7334802c41623b
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5391
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This is a preparatory change, align the function name with the rest
of the API, no functional change.
Change-Id: Ib967520f027b03eb1792b36ede52335df8e23941
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5390
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add possibility to supply custom CFI memory accessors via cfi_info
and override the default memory-mapped ones.
Change-Id: I1b6bc1db69fc33e8cdef96c41742c40e6d8917e9
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5147
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
